• Journal of Radiation Protection and Research
• /
• 제37권1호
• /
• pp.16-24
• /
• 2012

본 연구에서는 이중 모드 컴프턴 카메라의 측면 흡수부 개발을 위해 CsI(Tl) 섬광체에 실리콘 광다이오드를 결합한 섬광 검출기를 제작하였고, 이를 위한 신호처리회로를 설계 및 제작하였다. 개발된 신호처리회로는 에너지를 결정하는 파트와 타이밍을 결정하는 파트로 구성되어 있으며, 트리거 신호를 발생시키기 위해 상승 에지 선별기 및 TTL-to-NIM 로직 변환기를 포함하도록 개발하였다. 검출기와 초단의 신호처리회로(front-end electronics, FEE)는 AC 커플링 구조로 구성하였다. FEE의 잡음 특성은 전체 시스템의 성능에 크게 기여하므로 설계 시 고려해야 할 몇 가지 조건들에 대해 논의하였다. 이후 제작된 감마선 검출 시스템의 에너지 분해능 및 시간 분해능을 결정하였다. 평가된 에너지 분해능은 662 keV 피크와 511 keV 피크에 대해서 각각 12.0% 및 15.6% FWHM이었다. 시간 분해능은 59.0 ns로 평가되었다. 본 연구를 통해 제작된 섬광 검출기 및 신호처리회로의 성능이 기대에 다소 미치지 못하므로 결론에서는 성능 향상을 위한 추가 연구 방향에 대해 논의하였다.

• 한국전기전자재료학회논문지
• /
• 제19권7호
• /
• pp.655-661
• /
• 2006

Dielectric and piezoelectric properties of PMN-PZT ceramics with a high mechanical quality factor$(Q_m)$ and a low temperature sintering temperature were investigated as a function of PZN substitution in order to develop multilayer piezoelectric transformer for AC-DC converter. Multilayer piezoelectric transformers were subsequently manufactured using the PMN-PZN-PZT ceramic offering the optimal behavior and then the electrical performance were invetigated. At the sintering temperature of $940^{\circ}C$, density, electromechanical coupling factor$(k_p)$, mechanical qualify factor$(Q_m)$ and dielectric constant$(\varepsilon_r)$ of 8 mol% PZN substituted specimen were $7.73g/cm^3$, 0.524, 1573 and 1455, respectively. The PZN substitution caused a increase in the dielectric constant and the electromechnical coupling factor. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value at near the resonant frequency of 76.55 kHz and increased according to the increase of load resistance. The multilayer piezoelectric transformer with the output impedance coincided with the load resistance showed the temperature increase of less than $20^{\circ}C$ at the output power of 10 W. Based on the results, the manufactured multilayer transformer using the low temperature sintered PMN-PZN-PZT ceramics can be stably driven for both step-up and down transformers.

• 한국정보전자통신기술학회논문지
• /
• 제10권5호
• /
• pp.402-408
• /
• 2017

본 논문에서는 무선 신호전송을 위한 비접촉 방식의 AC 커플링 기반 육각 나선형 박막 인덕터의 주파수 특성을 분석하였다. 사각 나선형 인덕터와 육각 나선형 인덕터에 대하여 권선수 변화, 도체 선 폭 및 선 간격을 변화에 따른 주파수 특성을 비교 분석하였다. 육각 나선형 인덕터는 사각 나선형 인덕터와 비교하여 동일한 인덕턴스를 갖기 위하여 더 많은 권선수를 갖게 되지만 전체적인 도선의 길이는 짧아지게 된다. 이는 자기인덕턴스는 감소하고 상호인덕턴스가 증가하여 전체적인 인덕턴스는 같은 값을 가질 수 있다. 또한 전체적인 도선의 길이가 짧아지고 자기저항이 감소하므로 품질계수와 자기공진주파수의 성능을 확보할 수 있다. 제안된 육각 나선형 박막 인덕터는 2GHz에서 3.54nH의 인덕턴스와 5.0GHz에서 최댓값 14.00의 품질계수를 가지며, 약 11.3GHz에서 자기공진주파수를 가진다.

• 전자공학회논문지SC
• /
• 제37권6호
• /
• pp.64-72
• /
• 2000

본 논문은 고속전철 보조전원장치에 사용되는 2대의 PWM 컨버터 병렬운전에 관하여 다루고 있다. 고역률을 이루고 변압기 1차측 전류 고조파 성분을 줄이기 위하여 3레벨 PWM 스위칭 방법에 의해 제어되는 AC/DC PWM 컨버터의 병렬운전을 제안하였다. 본 논문에서는 변압기의 결합효과를 제거하기 위한 제어기법과 컨버터 2대 사이의 위상전이기법 및 전원과 제어기를 동기화하기 위한 영점 검출방식을 나타내었다. TMS320C31 마이크로 프로세서와 10［kVA] PWM 컨버터로 구성된 축소시스템에 의한 실험 결과들은 제안된 알고리즘의 타당성을 보여주고 있다.

• 전기화학회지
• /
• 제16권4호
• /
• pp.198-203
• /
• 2013

본 실험에서는 MMA와 tBMA의 공중합체를 합성하고, tert-butyl 그룹의 가수분해를 선택적으로 유도하여 poly(MMA-co-MA)를 제조하였다. 또한 말단에 에폭시기를 함유한 다양한 분자량의 PEO와 MA와의 grafting-onto 커플링 반응을 통해 같은 주사슬을 가지지만 부사슬의 길이가 다른 poly(MMA-co-PEGMA)를 합성하여 조성이 이온전도도에 미치는 영향을 평가하였다. AC-impedance로 측정한 상온 이온전도도는 MMA의 몰분율이 82%에서 $5.11{\times}10^{-8}Scm^{-1}$의 값이 얻어진 반면, 48%에서는 $1.88{\times}10^{-6}Scm^{-1}$로서 많은 PEGMA에서 높게 관찰되었다. 또한 에폭시기를 함유한 PEO의 분자량에 따라 이온전도도의 차이가 발생하는데, grafting-onto 법의 입체적 장애가 원인으로 고려되었다. 한편, 합성된 poly(MMA-co-PEGMA) 고분자 전해질은 상온에서 6V까지 우수한 전기화학적 안정성을 보여주었다.

• 한국광학회지
• /
• 제14권2호
• /
• pp.109-115
• /
• 2003

다기능성 아크릴레이트 단량체와 네마틱 액정 등을 혼합한 홀로그래픽 고분자 분산 액정 박막을 제작하고 액정의 농도와 피부에서 인가한 교류 전기장 등에 대한 실시간 회절효율을 측정하였다. WPDLC 박막에 기록된 홀로그램은 적절한 교류 전기장의 on/off에 의해 가역적으로 소거와 재생이 가능함을 보였다. 이러한 전기광학 특성을 이용하여 30 cm와 40 cm의 이중초점을 갖는 홀로그램 렌즈를 제작하였다.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.190-201
• /
• 2015

This paper uses the switching function approach to present a simple state model of the Vienna-type rectifier. The approach introduces the relationship between the DC-link neutral point voltage and the AC side phase currents. A novel direct power control (DPC) strategy, which is based on the sliding mode control (SMC) for Vienna I rectifiers, is developed using the proposed power model in the stationary ${\alpha}-{\beta}$ reference frames. The SMC-based DPC methodology directly regulates instantaneous active and reactive powers without transforming to a synchronous rotating coordinate reference frame or a tracking phase angle of grid voltage. Moreover, the required rectifier control voltages are directly calculated by utilizing the non-linear SMC scheme. Theoretically, active and reactive power flows are controlled without ripple or cross coupling. Furthermore, the fixed-switching frequency is obtained by employing the simplified space vector modulation (SVM). SVM solves the complicated designing problem of the AC harmonic filter. The simplified SVM is based on the simplification of the space vector diagram of a three-level converter into that of a two-level converter. The dwelling time calculation and switching sequence selection are easily implemented like those in the conventional two-level rectifier. Replacing the current control loops with power control loops simplifies the system design and enhances the transient performance. The simulation models in MATLAB/Simulink and the digital signal processor-controlled 1.5 kW Vienna-type rectifier are used to verify the fast responses and robustness of the proposed control scheme.

• 한국포장학회지
• /
• 제28권2호
• /
• pp.143-149
• /
• 2022

PCS needs to freely switch AC and DC to connect the battery, external AC loads and renewable energy in both directions for energy efficiency. Whenever converting happens, power loss inevitably occurs. Minimization of the power loss to save electricity and convert it for usage is a very critical function in PCS. PCS plays an important role in the ESS(Energy Storage System) but the importance of stabilizing semiconductors on PCB(Printed Circuit Board) should be empathized with a risk of failure such as a fire explosion. In this study, the temperature variation inside PCS was reviewed by cooling fan on top of PCS, and the vibration characteristics of PCS were analyzed during truck transportation for reliability of the product. In most cases, a cooling fan is mounted to control the inner temperature at the upper part of the PCS and components generating the heat placed on the internal aluminum cooling plate to apply the primary cooling and the secondary cooling system with inlet fans for the external air. Results of CFD showed slightly lack of circulating capacity but simulated temperatures were durable for components. The resonance points of PCS were various due to the complexity of components. Although they were less than 40 Hz which mostly occurs breakage, it was analyzed that the vibration displacement in the resonance frequency band was very insufficient. As a result of random-vibration simulation, the lower part was analyzed as the stress-concentrated point but no breakage was shown. The steel sheet could be stable for now, but for long-term domestic transportation, structural coupling may occur due to accumulation of fatigue strength. After the test completed, output voltage of the product had lost so that extra packaging such as bubble wrap should be considered.

• Journal of Electrical Engineering and Technology
• /
• 제11권6호
• /
• pp.1656-1663
• /
• 2016

A capacitive wireless power transfer (C-WPT) system uses an electric field to transmit power through a physical isolation barrier which forms a pair of ac link capacitors between the metal plates. However, the physical dimension and low dielectric constant of the interface medium severely limit the effective link capacitance to a level comparable to the main switch output capacitance of the transmitting circuit, which thus narrows the soft-switching range in the light load condition. Moreover, by fundamental limit analysis, it can be proved that such a low link capacitance increases operating frequency and capacitor voltage stress in the full load condition. In order to handle these problems, this paper investigates optimal design of double matching transformer networks for C-WPT. Using mathematical analysis with fundamental harmonic approximation, a design guideline is presented to avoid unnecessarily high frequency operation, to suppress the voltage stress on the link capacitors, and to achieve wide ZVS range even with low link capacitance. Simulation and hardware implementation are performed on a 5-W prototype system equipped with a 256-pF link capacitance and a 200-pF switch output capacitance. Results show that the proposed scheme ensures zero-voltage-switching from full load to 10% load, and the switching frequency and the link capacitor voltage stress are kept below 250 kHz and 452 V, respectively, in the full load condition.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.320-328
• /
• 2016

The introduction of renewable energy sources into the AC grid can change and weaken the strength of the grid, which will in turn affect the stability and robustness of the doubly-fed induction generator (DFIG) wind farm. When integrated with weak grids, the DFIG wind turbine with vector power control often suffers from poor performance and robustness, while the DFIG wind turbine with synchronized control provides better stability. This paper investigates the critical short circuit ratios of DFIG wind turbine with vector power control and synchronized control, to analyze the stability boundary of the DFIG wind turbine. Frequency domain methods based on sensitivity and complementary sensitivity of transfer matrix are used to investigate the stability boundary conditions. The critical capacity of DFIG wind farm with conventional vector power control at a certain point of common coupling (PCC) is obtained and is further increased by employing synchronized control properly. The stability boundary is validated by electromagnetic transient simulation of an offshore wind farm connected to a real regional grid.