• Geophysics and Geophysical Exploration
• /
• v.24 no.3
• /
• pp.73-77
• /
• 2021

Induced polarization (IP) is useful for mineral exploration and hydrogeological studies by visualizing the electrochemical reactions at the interface between polarized minerals and groundwater. Frequency-domain IP (FDIP) is not actively applied to field surveys because it takes longer to acquire data, despite its higher data quality than conventional time-domain IP. However, data quality is more important in current mineral exploration as the targets gradually shift to deep or low-grade ore bodies. In addition, the measurement time reduced by automated instrumentation increases the potential for FDIP field applications. Therefore, we demonstrate that FDIP can detect mineral exploration targets by performing geophysical logging in the boreholes of a skarn deposit, in South Korea. Alternating current (AC) resistivity, percent frequency effect (PFE) and metal factor (MF) were calculated from impedance values obtained at two different frequencies. Skarn zones containing magnetite or pyrite showed relatively low AC resistivity, high PFE, and high MF compared to other zones. Therefore, FDIP surveys are considered to be useful for mineral exploration.

• KIPS Transactions on Computer and Communication Systems
• /
• v.10 no.7
• /
• pp.199-204
• /
• 2021

Digital substation refers to a substation that digitizes functions and communication methods of power facilities such as monitoring, measuring, control, protection, and operation based on IEC 61850, an international standard for the purpose of intelligent power grids. Based on the intelligent operating system, efficient monitoring and control of power facilities is possible, and automatic recovery function and remote control are possible in the event of an accident, enabling rapid power failure recovery. With the development of digital technology and the expansion of the introduction of eco-friendly renewable energy and electric vehicles, the spread of direct current distribution systems is expected to expand. MVDC is a system that utilizes direct current lines with voltage levels and transmission capacities between HVDCs applied to conventional transmission systems and LVDCs from consumers. Converting existing lines in substations, where most power equipment is alternating current centric, to direct current lines will reduce transmission losses and ensure greater current capacity. The process bus of a digital substation is a communication network consisting of communication equipment such as Ethernet switches that connect installed devices between bay level and process level. For MVDC linkage to existing digital substations, the process level was divided into two buses: AC and DC, and a system that can be comprehensively managed in conjunction with diagnostic IEDs as well as surveillance and control was proposed.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.2
• /
• pp.167-177
• /
• 2016

This work investigated the decomposition of aqueous anatoxin-a originated from cyanobacteria using an underwater dielectric barrier discharge plasma system based on a porous ceramic tube and an alternating current (AC) high voltage. Plasmatic gas generated inside the porous ceramic tube was uniformly dispersed in the form of numerous bubbles into the aqueous solution through the micro-pores of the ceramic tube, which allowed an effective contact between the plasmatic gas and the aqueous anatoxin-a solution. Effect of applied voltage, treatment time and the coexistence of nutrients such as $NO_3{^-}$, $H_2PO_4{^-}$ and glucose on the decomposition of anatoxin-a was examined. Chemical analyses of the plasma-treated anatoxin-a solution using liquid chromatography-mass spectrometry (LC-MS) and ion chromatography (IC) were performed to elucidate the mineralization mechanisms. Increasing the voltage improved the anatoxin-a decomposition efficiency due to the increased discharge power, but the energy required to remove a given amount of anatoxin-a was similar, regardless of the voltage. At an applied voltage of 17.2 kV (oxygen flow rate: $1.0L\;min^{-1}$), anatoxin-a at an initial concentration of $1mg\;L^{-1}$ (volume: 0.5 L) was successfully treated within 3 min. The chemical analyses using LC-MS and IC suggested that the intermediates with molecular weights of 123~161 produced by the attack of plasma-induced reactive species on anatoxin-a molecule were further oxidized to stable compounds such as acetic acid, formic acid and oxalic acid.

• The Journal of Korean Association of Computer Education
• /
• v.4 no.1
• /
• pp.127-134
• /
• 2001

Many teachers at vocational high schools have had difficulties overcoming the gap between what students know and what students have to achieve in many topics. Mathematics is toughest of all, since most of textbooks in electronics are assuming student's basic knowledge in math. Considering that many students with very low achievements are entering vocational high schools, reality is far from such assumption. Inevitably, we have to face two difficult questions; do we have enough time to teach these kids all the math that they need in two years? If not, what alternatives we should adopt? We just do not have enough time and therefore find out a way to cope with harsh reality. According to our preliminary study, we suggest that multimedia-based CAI may be the best way to attack this problem. From hardware point of view, fortunately, many of vocational high schools are reasonably equipped for multimedia-based education. However there have been hardly any effort to develop courseware for vocational education in Korea. In this paper, a CAI title for learning basic characteristics of alternating current has been designed and implemented. The developed multimedia-based CAI title has been applied with respect to first grade students at local vocational high schools. A survey after classes shows that CAI could help student feel much comfortable with Basic Electricity course and grasp physical understanding much easily. Accordingly we conclude that classes adopting CAI would be of great help to put education in vocational high schools on the right track.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.491-491
• /
• 2011

Transparent and flexible electronic devices that are light-weight, unbreakable, low power consumption, optically transparent, and mechanical flexible possibly have great potential in new applications of digital gadgets. Potential applications include transparent displays, heads-up display, sensor, and artificial skin. Recent reports on transparent and flexible field-effect transistors (tf-FETs) have focused on improving mechanical properties, optical transmittance, and performances. Most of tf-FET devices were fabricated with transparent oxide semiconductors which mechanical flexibility is limited. And, there have been no reports of transparent and flexible all-organic tf-FETs fabricated with organic semiconductor channel, gate dielectric, gate electrode, source/drain electrode, and encapsulation for sensor applications. We present the first demonstration of transparent, flexible all-organic sensor based on multifunctional organic FETs with organic semiconductor channel, gate dielectric, and electrodes having a capability of sensing infrared (IR) radiation and mechanical strain. The key component of our device design is to integrate the poly(vinylidene fluoride-triflouroethylene) (P(VDF-TrFE) co-polymer directly into transparent and flexible OFETs as a multi-functional dielectric layer, which has both piezoelectric and pyroelectric properties. The P(VDF-TrFE) co-polumer gate dielectric has a high sensitivity to the wavelength regime over 800 nm. In particular, wavelength variations of P(VDF-TrFE) molecules coincide with wavelength range of IR radiation from human body (7000 nm ~14000 nm) so that the devices are highly sensitive with IR radiation of human body. Devices were examined by measuring IR light response at different powers. After that, we continued to measure IR response under various bending radius. AC (alternating current) gate biasing method was used to separate the response of direct pyroelectric gate dielectric and other electrical parameters such as mobility, capacitance, and contact resistance. Experiment results demonstrate that the tf-OTFT with high sensitivity to IR radiation can be applied for IR sensors.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.161-166
• /
• 2005

The plasma ion density in AC-PDP has shown to be increased from $5.6{\times}10^{11}cm^{-3}$ to $9.0{\times}10^{11)cm^{-3}$ as the Xe mixture ratio to neon increase from 1 % to 10 %, respectively, at fixed pressure of 400 Torr, by using the micro-Langmuir probe. It is noted that the plasma ion density is density increases as the gas pressure increases in this experiment. The electron temperature decreases from 2.3 to 1.2 eV as the Xe mole fraction increases from 1 % to 10 % at fixed pressure of 400 Torr, which is measured by the micro Langmuir probe and high-speed ICCD camera in this experiment. It is noted that the electron temperature decreases as the gas pressure increases from 150 to 400 Torr in this experiment. It is also observed that the exited Xe atom density and the plasma ion density are in strong correlation sharp between each other in this experiment. It is noted that $5.2{\times}10^{12}cm^{-3}$ in the $1s_5$ metastable state and $1.2{\times}10^{12}cm^{-3}$ in the $1s_4$ resonance state for the PDP cell with gap of 50 um distances under the fixed gas pressure of 400 Torr and Xe content ratio of 10 %.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.2
• /
• pp.68-74
• /
• 2014

The seed step-coverage enhancement process (SSEP) using Pd/Cu/PVP colloids was investigated for the filling of through silicon via (TSV) without void. TEM analysis showed that the Pd/Cu nano-particles were well dispersed in aqueous solution with the average diameter of 6.18 nm. This Pd/Cu nano-particles were uniformly deposited on the substrate of Si/$SiO_2$/Ti wafer using electrophoresis with the high frequency Alternating Current (AC). After electroless Cu deposition on the substrate treated with Pd/Cu/PVP colloids, the adhesive property between deposited Cu layer and substrate was evaluated. The Cu deposit obtained by SSEP with Pd/Cu/PVP colloids showed superior adhesion property to that on Pd ion catalyst-treated substrate. Finally, by implementing the SSEP using Pd/Cu/PVP colloids, we achieved 700% improvement of step coverage of Cu seed layer compared to PVD process, resulting in void-free filling in high aspect ratio TSV.

• Journal of Biomedical Engineering Research
• /
• v.45 no.2
• /
• pp.101-107
• /
• 2024

Steady-state visual evoked potential-based brain-computer interface (SSVEP-BCI) is one of the promising systems that can serve as an alternative input device due to its stable and fast performance. However, one of the major bottlenecks is that some individuals exhibit no or very low SSVEP responses to flickering stimulation, known as SSVEP illiteracy, resulting in low performance on SSVEP-BCIs. However, a lengthy duration is required to enhance multiple SSVEP responses using traditional single-frequency transcranial alternating current stimulation (tACS). This research proposes a novel approach using dual-frequency tACS (df-tACS) to potentially enhance SSVEP by targeting the two frequencies with the lowest signal-to-noise ratio (SNR) for each participant. Seven participants (five males, average age: 24.42) were exposed to flickering checkerboard stimuli at six frequencies to determine the weakest SNR frequencies. These frequencies were then simultaneously stimulated using df-tACS for 20 minutes, and the experiment was repeated to evaluate changes in SSVEP responses. The results showed that df-tACS effectively enhances the SNR at each targeted frequency, suggesting it can selectively improve target frequency responses. The study supports df-tACS as a more efficient solution for SSVEP illiteracy, proposing further exploration into multi-frequency tACS that could stimulate more than two frequencies, thereby expanding the potential of SSVEP-BCIs.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.1
• /
• pp.135-140
• /
• 2022

In addition to the stack that directly generates electricity by the reaction of hydrogen and oxygen, the fuel cell power generation system has a reformer that generates hydrogen from various fuels such as methanol and natural gas. It also consists of a power converter that converts the DC voltage generated in the stack into a stable AC voltage. The fuel cell output of such a system is direct current, and in order to be used at home, an inverter device that converts it into alternating current through a power converter is required. In addition, a DC-DC step-up converter is used to boost the fuel cell voltage to about 30~70V, which is the inverter operating voltage, to about 380V. The DC-DC step-up converter is a DC voltage variable device that exists between the fuel cell output and the inverter. Accordingly, since a constant output voltage of the converter is generated in response to a change in the output voltage of the fuel cell, the inverter can receive constant power regardless of the voltage change of the fuel cell. Therefore, in this paper, we discuss the detailed hardware design of the full-bridge converter, which is the main power source of the inverter that receives the fuel cell output voltage (30~70V) as an input and is applied to the grid among the members of the fuel cell power generation system.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.2
• /
• pp.59-66
• /
• 2020

Effects of Na₂SiO₃ concentration added into 0.1 M NaOH + 0.05 M NaF solution on the formation behavior and properties of PEO films on AZ91 Mg alloy were investigated under 1200 Hz of alternating current (AC) by voltage-time curves, in-situ observation of arc generation behavior and measurements of film thickness, surface roughness and micro vickers hardness. In the absence of Na₂SiO₃ in the 0.1 M NaOH + 0.05 M NaF solution, about 4 ㎛ thick PEO film was formed within 1 min and then PEO film did not grow but white spots were formed by local burning. Addition of Na₂SiO₃ up to 0.2 M caused more increased formation voltage and growth of PEO film with uniform generation of arcs. Addition of Na₂SiO₃ from 0.2 M to 0.4 M showed nearly the same voltage-time behavior and uniform arc generation. Addition of Na₂SiO₃ more than 0.5 M resulted in a decrease of formation voltage and non-uniform arc generation due to local burning. PEO film growth rate increased with increasing added Na₂SiO₃ concentration but maximum PEO film thickness was limited by local burning if added Na₂SiO₃ concentration is higher than 0.5 M. Surface roughness of PEO film increased with increasing added Na₂SiO₃ concentration and appeared to be proportional to the PEO film thickness. PEO film hardness increased with increasing added Na₂SiO₃ concentration and reached a steady-state value of about 930 H_V at more than 0.5 M of added Na₂SiO₃ concentration.