• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.169-174
• /
• 2012

Electromagnetic interference(EMI) shielding effectiveness(SE) was investigated in of woven fabric made of epoxy/copper-nickel fabrics and nickel coated carbon fiber reinforced acrylonitrile-butadiene-styrene(ABS) composites. The coaxial transmission line method was used to measure the EMI shielding effectiveness of the composites. We designed and constructed a measuring system, consisting of a network analyzer and a device that plays the serves as a sample holder and at the same time as a transmission medium of the incident electromagnetic wave. The measurement of SE were carried out frequency range from 100MHz to 2GHz. It is observed that the SE of the composits is the frequency dependent increase with the increase in nickel coated carbon fibre volume fraction. The nickel coating with 20wt% ABS composite was shown to exhibit up to 60dB of SE. The result that nickel coated carbon fibre ABS composite can be used for the purpose of EMI shielding as well as for some microwave applications.

• Elastomers and Composites
• /
• 제30권2호
• /
• pp.105-111
• /
• 1995

The thermal decomposition of the paper sludge with poly (acrylonitrile-butadiene-styrene) was using a thermal analysis techniques in the stream of nitrogen gas of 30ml/min at various heating rates from 4 to $20^{\circ}C/min$. The mathmatical, derivative and integral method were used to obtain values of activation energy of decomposition reaction. 1. The values of activation energy evaluated by derivative and Intergral method were consistent with each other very well. 2. The maximum value of heat of decomposition evaluated by DSC method was 10.120cal/g at weight ratio of paper sludge/ABS=20/80. 3. The thermogravimetric trace curve agreed with the theoretical equation.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2004년도 추계학술대회논문집
• /
• pp.22-28
• /
• 2004

Pit and rim formation on the Acrylonitrile Butadiene Styrene(ABS) plastic surface was evaluated after it was irradiated by $CO_2$ and Nd:YAG laser beams. Our results show that thermal effect floor was well observed at the outer wall of pit with $CO_2$ laser irradiated while it was not the case with Nd:YAG laser irradiated. Also the volume and depth of pit formation increase proportionally with the energy intensities of two laser irradiations, but there are significant differences in the slope, width, and FWHM of the Pit formation with two types of laser irradiations. This result shows that $CO_2$ laser irradiation leads to better cooling contraction effect while Nd:YAG laser irradiation induces better recoil pressure effect during the interaction between ABS plastic and laser beam irradiation. The shape of the laser marking could vary significantly depending on the traveling path of molten plastic during injection molding of ABS plastic. Therefore, the selection of material and molding process can have a great impact on the performance of optical storage media.

• Composites Research
• /
• 제35권6호
• /
• pp.447-455
• /
• 2022

현재 해양 미세플라스틱에 의한 해양 환경 오염문제가 국제적으로 심각하게 대두되고 있다. 이와 관련하여 본 연구에서는 휴대용 미세플라스틱 수거 장비의 경량화 개발을 위해 대한민국 전국 21개소 해안가에서의 미세플라스틱종류와개수를조사하였고, 미세플라스틱수거장비진공장비의내구성, 내부식성, 경량화를위해 CFRP(Carbon Fiber Reinforced Plastic), GFRP(Glass Fiber Reinforced Plastic), ABS(Acrylonitrile Butadiene Styrene copolymer), aluminum과 같은 다양한 소재를 적용하여 설계 및 해석을 수행하였다. 해안가에서의 시료 채취 및 분류결과 함덕해수욕장에서 미세플라스틱이 가장 많이 분포되어 있는 것을 확인하였고, 주로 폴리스타이렌(Polystyrene)의 미세플라스틱이 분포되어 있는 것으로 나타났다. 해안가 현장 조사를 통한 입자정보 분석과 전산유체해석을 통해 모래 및 불순물 등의 입자 유동속도 및 분포를 분석하였고, 이를 진공 본체 내부의 중요 부품인 싸이클론 장치의 구조해석에 적용하였다. 싸이클론 장치의 모래 및 불순물 흡입 시 발생되는 입자 충격을 고려한 구조해석 결과 CFRP, GFRP, aluminum, ABS의 순으로 구조적 안전성이 우수한 것으로 평가되었다. 경량화 측면으로는 싸이클론 장치에 aluminum 소재를 적용했을 때와 비교하여 CFRP는 53%, GFRP는 47%, ABS는 61%의 경량화가 가능한 것으로 나타났다.

• 공업화학
• /
• 제23권4호
• /
• pp.372-376
• /
• 2012

탄소나노튜브는 좋은 전기 기계적 및 열적 특성을 가진 복합 재료 분야에서 가장 이상적인 나노 충전재이다. 따라서 탄소나노튜브의 복합 재료는 전도성 재료, 고강도를 가지면서 가벼운 무게를 가지는 재료에 이용된다. 탄소나노튜브 복합재료의 주요 문제점은 탄소나노튜브의 나쁜 분산에 있다. 본 연구에서는 다중벽 탄소나노튜브(MWNT)를 물리적 방법으로 전처리하였다. 전처리 후, 고분자/MWNT nanocomposites는 용해 공정에 의해 분산되었다. 물리적 방법은 고분자 wrapping 방법에 의해 준비되었다. ABS/MWNT 복합 재료의 기계적 및 전기적 특성을 SAN과 함께 wrapping된 MWNT와 미처리된 MWNT와 혼합된 ABS의 속성을 비교하여 연구하였다. MWNT가 wrapping된 복합체의 인장강도는 증가하였으나 충격강도는 감소한 수치를 보였다. 전기적 물성의 향상에는 미처리시료와 비교해 볼 때 큰 효과가 없었다.

• 한국임상수의학회지
• /
• 제40권4호
• /
• pp.268-275
• /
• 2023

In this paper, we designed 3D-printed orthopedic splint models for patient-specific external coaptation on fracture healing and analyzed the stability of the models through finite element method (FEM) analysis under compressive load conditions. Polylactic acid (PLA) and acrylonitrile-butadiene-styrene (ABS) based 3D splint models of the thicknesses 1, 3, 5 and 7 mm were designed, and Peak von Mises stress (PVMS) and maximum displacement (MD) of the models were analyzed by FEM under compressive loads of 50, 100, 150, and 200 N. The FEM results indicated that PVMS and MD values, regardless of material, had a negative correlation with the thickness of the models and a positive correlation with the compressive load. There was a risk of splint deformation under conditions more extreme than 100 N with 5 mm thickness. For successful clinical application of 3D-printed orthopedic splints in veterinary medicine, it is recommended that the splint should be produced not less than 5 mm thickness. Also, it is expected to be stable when the splint is applied to situations with a compressive load of 100 N or less. There is an advantage of overcoming the limitations of the existing bandage method through 3D-printing technology as well as verifying the stability through 3D modeling before application. Such 3D printing technology will be widely used in veterinary medicine and various fields as well as orthopedics.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.42-48
• /
• 2010

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) were welded by a combination of a diode laser and a CNC machining center. Laser beam delivered through the transparent PC and was absorbed in an opaque ABS. Polymers were melted and joined by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead and cross-section were analyzed for weld quality, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was measured to be 3.75mm. The shear strength at the given condition was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in a CNC machining system, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision.

• Korea-Australia Rheology Journal
• /
• 제17권1호
• /
• pp.1-7
• /
• 2005

Acrylonitrile-Butadiene-Styrene (ABS), polycarbonate (PC) and their alloys are an important class of engineering thermoplastics that are widely used for automotive industry, computer and equipment housings. For the process of recycling mixtures of ABS and PC, it is desirable to know how sensitive the blend properties are to changes in compositions. It was for this reason that blends of virgin ABS and virgin PC at five different compositions, namely, $15\%,\;30\%,\;50\%,\;70%$ and $85\%$ by weight of ABS were prepared and characterised by rheological and mechanical measurements. Rheological properties of these blends in steady, oscillatory and transient step shear and mechanical properties, namely, tensile strength, elongation-at-break and Izod impact strength are reported. The results show that PC behaves in a relatively Newtonian manner, but ABS exhibits significant shear thinning. The ABS-rich blends show a trend that is similar to that of ABS, while PC-rich blends, namely $0\%$ and $15\%$, exhibit a nearly Newtonian behaviour. However, at a fixed shear rate or frequency, the steady shear or the dynamic viscosity varied respectively in a non-mono-tonic manner with composition. Except for $15\%$ blend, the viscosities of other blends fall into a narrow band indicating a wide-operation window of varying blend ratio. The blends exhibited a lower viscosity than either of the two pure components. The other noticeable feature was that the blends at $70\%$ and $85\%$ ABS content had a higher G' than pure ABS, indicating an enhancement of elastic effect. The tensile yield strength of the blends followed the 'rule of mixtures' showing a decreasing value with the increase of ABS content in PC. However, the elongation-at-break and the impact strength did not appear to obey this 'rule of mixtures,' which suggests that morphology of the blends also plays a significant role in determining the properties. Indeed, scanning electron micrographs of the fracture surfaces of the different blends validate this hypothesis, and the $15\%$ blend is seen to have the most distinct morphology and correspondingly different behaviour and properties.

• 대한환경공학회지
• /
• 제36권11호
• /
• pp.771-780
• /
• 2014

본 연구에서는 광촉매 nano-ZnO 분말을 수질정화에 사용 후 회수 공정을 생략하기 위해 지지체에 고정화/안정화 시 발생하는 효율 저하를 유기오염물의 수착(sorption)으로 극복하고 복합체로부터 nano-ZnO의 탈리(detachment) 현상을 방지 하고자 실리콘(silicone), ABS (acrylonitrile-butadiene-styrene), 에폭시(epoxy), 부타디엔 고무(butadiene rubber)를 선정하여 nano-ZnO/Organic composites (NZOCs)를 제조하였다. 또한, 개발된 다양한 NZOCs의 수중 안정성을 규명 하고, 지하수 내 대표적인 난분해성 유기오염물인 1,1,2-trichloroethylene (TCE)를 대상으로 액상에서 제거 실험을 통해 NZOCs의 활용 타당성을 검증하였다. 연구 결과, 내수성실험을 통해 개발된 NZOCs는 수질정화 용도로 장기간 사용이 타당함을 확인하였다. 또한, FE-SEM, EDX, imaging 분석을 통해 Nano-ZnO/Butadiene rubber Composite (NZBC)는 다양한 공극과 균열에 nano-ZnO 분말이 비교적 균질하게 부착된 반면, Nano-ZnO/Silicone Composite (NZSC), Nano-ZnO/ABS Composite (NZAC), Nano-ZnO/Epoxy Composite (NZEC)는 표면에 공극과 균열이 발달되지 않아 불균질한 부착이 이뤄졌음을 확인할 수 있었다. 또한, NZBC는 초기농도 대비 60%의 TCE 수착 능을 보였는데 이는 다른 유기계 지지체와 달리 비결정성 고분자이며, TCE 분자의 소수성 분배가 활발히 발생하였기 때문으로 판단된다. 액상에서 TCE의 제거효율(수착+광분해)은 NZBC가 99% 제거 효율로 가장 우수했으며, 복합체 주입량이 증가할수록 TCE 제거효율이 크게 증가하였다. 이러한 결과는 butadiene rubber의 우수한 수착능과 nano-ZnO의 광촉매 기작이 동시에 발생하였기 때문인 것으로 판단된다. 마지막으로 액상에서 TCE 제거는 선형모델을 활용해서 비교적 잘 모사할 수 있었으며($R^2{\geq}0.936$), NZBC의 총 반응상수($K_{app}$)는 UV에 의한 TCE 분해상수($K_{photolysis}$) 대비 2.64~3.85배로 높은 값으로 확인되어 butadiene rubber가 TCE 수착 효율이 우수하며, 광분해 기작을 억제하지 않는 지지체로 활용 가능한 것으로 판단하였다.

• 공업화학
• /
• 제10권1호
• /
• pp.118-123
• /
• 1999

본 연구에서는 자동차의 instrument panel로부터 분리, 회수된 재생 PC/ABS계에 흡착되어 있는 PU foam이 가공온도조건에 따라 PC/ABS계의 모폴로지 및 기계적 물성에 미치는 영향을 조사함으로써 상용화제 첨가없이 PU의 열적성질을 이용한 모폴로지 제어에 의해 큰 폭의 물성저하를 막아 재생 PC/ABS를 자동차 라디에디터 그릴 소재로 적용하고자 하였다. 가공 온도조건에 따른 PU의 열적특성에 초점을 맞추어 고온 ($260^{\circ}C$) 및 저온 ($220^{\circ}C$)에서 재생PC/ABS와 신재 PC/ABS를 다양한 조성으로 용융 블렌드하여 고차구조 및 기계적 물성을 조사하였다. 신재 함량이 증가함에 따라 물성이 향상되었고, 고온 및 저온용융 블렌드물의 물성에는 큰 차이가 없었으나 충격강도는 고온용융 블렌드물이 월등히 우수하였다. 이것은 PU foam이 고온에서 높은 전단응력을 받아 보다 미세하고 균일하게 분산되었기 때문이라는 것을 발견했다.