• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.3
• /
• pp.629-634
• /
• 2024

The Korea Research Institute of Ships and Ocean Engineering (KRISO) has developed a test module that can vertically ascend and descend with a buoyancy engine to verify the performance of the developed buoyancy engine. The independent test module has been tested in the Ocean Engineering Basin(C.M.Lee et al., 2023). After that, more tests were performed in the Deep Ocean Engineering Basin and at sea. In the 50-meter depth pit test of the Deep Ocean Engineering Basin, there were no problems with the ascent and descent operations, but the buoyancy engine was not properly maintained due to various problems in the independent test module, resulting in a difference between the calculated results using the solution of the equations of motion and the actual measurement results. The East Sea test was conducted at a depth of approximately 110 meters north-east of Pohang, with a dive to 100 meters. The difference between the pressure sensor value and the calculated value was observed, but after checking the results of the underwater position tracking device(USBL, Ultra Short Base Line system), it was estimated that the difference was caused by the influence of the current.

• BMB Reports
• /
• v.37 no.5
• /
• pp.629-633
• /
• 2004

NADPH-cytochrome P450 reductase (CPR) transfers electrons from NADPH to cytochrome P450, and catalyzes the one-electron reduction of many drugs and foreign compounds. Various forms of spectrophotometric titration have been performed to investigate the electron-accepting properties of CPR, particularly, to examine its ability to reduce cytochrome c and ferricyanide. In this study, the reduction of 1,1-diphenyl-2-picrylhydrazyl (DPPH) by CPR was assessed as a means of monitoring CPR activity. The principle advantage of DPPH is that its reduction can be assayed directly in the reaction medium by a continuous spectrophotometry. Thus, electrons released from NADPH by CPR were transferred to DPPH, and DPPH reduction was then followed spectrophotometrically by measuring $A_{520}$ reduction. Optimal assay concentrations of DPPH, CPR, potassium phosphate buffer, and NADPH were first established. DPPH reduction activity was found to depend upon the strength of the buffer used, which was optimal at 100 mM potassium phosphate and pH 7.6. The extinction coefficient of DPPH was $4.09\;mM^{-1}\;cm^{-1}$. DPPH reduction followed classical Michaelis-Menten kinetics ($K_m\;=\;28\;{\mu}M$, $K_{cat}\;=\;1690\;min^{-1}$). This method uses readily available materials, and has the additional advantages of being rapid and inexpensive.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2003.06a
• /
• pp.161-164
• /
• 2003

This research presents the parallel control scheme of PID servo-driver for shaping of the curved glass. The designed system consists of a PC, main controller and 11 servo-drivers. Each elements are connected by using RS-232C and 8-bit bus communication. In order to guarantee the stability and the control performance, we use the LM629, a precision PID motion controller, and LMD18200, a H-bridge on the servo-drivers. PC calculates position values of 11 DC motors by using the pre-determined curvature value and offers the user interface environment operator.

• Communications of the Korean Mathematical Society
• /
• v.37 no.2
• /
• pp.607-629
• /
• 2022

In this paper, we give the necessary and sufficient condition for the conformal mapping ϕ : (ℝⁿ, g₀) → (Nⁿ, h) (n ≥ 3) to be triharmonic where we prove that the gradient of its dilation is a solution of a fourth-order elliptic partial differential equation. We construct some examples of triharmonic maps which are not biharmonic and we calculate the trace of the stress-energy tensor associated with the triharmonic maps.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.8
• /
• pp.629-633
• /
• 2001

Electrical properties of the $\alpha$-In$_2$Se$_3$ single crystals grown by use of the Bridgman technique were examined in the transition temperature range between $\alpha$-phase and $\beta$-phase. $\alpha$-In$_2$Se$_3$ single crystal has ' the rhombohedral structure and lattice constants are a=4.025 $\AA$, c=28.771 $\AA$ in c-axis. The transition temperatures of the stoichiometric $\alpha$-In$_2$Se$_3$ single crystal is 198.8$^{\circ}C$ according to the specimens. The temperature of $\alpha$longrightarrow$\beta$ phase transition decreased but the temperature of $\beta$longrightarrow$\alpha$ phase transition increased as the number of heating-cooling cycle increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.629-630
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.629-630
• /
• 2008

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.629-634
• /
• 2016

This paper describes the implementation of a ZigBee sensor node that can be utilized as a multiband and machine to machine (M2M) communication gateway. The IEEE 802.15.4-2003 standard was used as the wireless network frequency band. Ember's Type EM357 SoC was used as the transmission and reception device to perform the communication function, and it was also used for both the main M2M gateway and the sensor node. For the implementation of the operating protocol, EmberZNet Stack 4.5.4 from the Ember Corporation was used. The measurement of the reception sensitivity in the receiving module and the actual output signal from the reference were obtained from the transmission of a packet, and the packet included the M2M gateway within the attached ZigBee sensor. The packet error rate was measured as 0% with a -98 dBm reception sensitivity at the ZigBee frequency. In addition, excellent current characteristics of the ZigBee modules were shown by the implementation of the low-power circuit.

• Korean Journal of Materials Research
• /
• v.17 no.12
• /
• pp.629-633
• /
• 2007

This study examined the effect of growth temperature on the electrical and optical properties of hydrogenated Al-doped zinc oxide (AZO:H) thin films deposited by rf magnetron sputtering using a ceramic target (98 wt.% ZnO, 2 wt.% $Al_2O_3$). Various AZO films on glass were prepared by changing the substrate temperature from room temperature to $200^{\circ}C$. It was shown that intentionally incorporated hydrogen plays an important role on the electrical properties of AZO : H films by increasing free carrier concentration. As a result, in the 2% $H_2$ addition at the growth temperature of $150^{\circ}C$, resistivity of $3.21{\times}10^{-4}{\Omega}{\cdot}cm$, mobility of $21.9cm^2/V-s$, electric charge carrier concentration of $9.35{\times}10^{20}cm^{-3}$ was obtained. The AZO : H films show a hexagonal wurtzite structure preferentially oriented in the (002) crystallographic direction.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.