• Journal of Conservation Science
• /
• v.33 no.1
• /
• pp.43-49
• /
• 2017

The ancient paper document we chose as a case study for our research is "One Hundred Poets of the Tang Dynasty", which is housed in the Ryukoku University Library. The purpose of this research is to introduce a method to analyze the surface roughness and microstructure at a high resolution. In addition, we attempt to quantitatively measure the surface unevenness of the types and curve structure. We used a tridimensional digital microscopy as a non-contact and a non-destructive method to study ancient cultural paper. The information contained in the paper may be lost in the process of applying strong pressure to clean and lining or press. However, this microscopic measurement method can non-destructively analyze a large amount of data in old printed books. Moreover, it enables observing them directly with reflected light. Therefore, this method may be useful for collecting printed information remaining on the surface of the paper.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.595-597
• /
• 2015

LMC X-4 is an eclipsing high-mass X-ray binary exhibiting a superorbital modulation with a period of ~ 30:5 days. We present a detailed study of the variations of the superorbital modulation period with a time baseline of ~ 18 years. The period determined in the light curve collected by the Monitor of All-sky X-ray Image (MAXI) significantly deviates from that observed by the All Sky Monitor (ASM) onboard the Rossi X-ray Timing Explorer (RXTE). Using the data collected by RXTE/ASM, MAXI, and the Burst Alert Telescope (BAT) onboard Swift, we found a significant period derivative, $\dot{P}=(2.08{\pm}0.12){\times}10^{-5}$. Furthermore, the O{C residual shows complex short-term variations indicating that the superorbital modulation of LMC X-4 exhibits complicated unstable behaviors. In addition, we used archive data collected by the Proportional Counter Array (PCA) on RXTE to estimate the orbital and spin parameters. The detected pulse frequencies obtained in small time segments were fitted with a circular orbital Doppler shift model. In addition to orbital parameters and spin frequency for each observation, we found a spin frequency derivative of $\dot{v}=(6.482{\pm}0.011){\times}10^{-13}Hz{\cdot}s^{-1}$. More precise orbital and spin parameters will be evaluated by the pulse arrival time delay technique in the future.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.9-17
• /
• 1999

Viscoelastic characteristics of cured phenolic resin/carbon fiber composite materials were investigated through glass transition and degradation reaction processes in the high temperature region up to $400^{\circ}C$. A typical glass transition of the cross-linked thermoset polymer was followed by irreversible degradation reactions, which were exhibited by the increasing storage modulus and loss modulus peak. A degradation master curve was constructed by using the vertical and horizontal shift factors, both of which complied well with the Arrhenius equation in light of the kinetic expression of degradation rate constants. Using an analogy to the Havriliak-Negami equation in dielectric relaxation phenomena, a viscoelastic modeling methodology was developed to characterize the frequency- and temperature-dependent complex moduli of the degrading thermoset polymer composite systems. The temperature-dependent relaxation time of the degrading composites was determined in a continuous fashion and showed a minimum relaxation time between the glass transition and degradation reaction regions. The capability of the developed modeling methodology was demonstrated by describing the complex behavior of the viscoelastic complex moduli of reacting phenolic resin composite systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.21-27
• /
• 2018

FRN (Full range Naphtha) is distilled from crude oil in a Naphtha Splitter Unit and is separated into the Light Straight Naphtha, Heavy Naphtha, and kerosene according to the boiling point in sequence. This separation is conducted using a series of binary-like columns. In this separation method, the energy consumed in the reboiler is used to separate the heaviest components and most of this energy is discarded as vapor condensation in the overhead cooler. In this study, the first two columns of the separation process are replaced with the Petlyuk column. A structural design was exercised by a stage to stage computation with an ideal tray efficiency in the equilibrium condition. Compared to the performance of a conventional system of 3-column model, the design outcome indicates that the procedure is simple and efficient because the composition of the liquid component in the column tray was designed to be similar to the equilibrium distillation curve. An analysis of the performance of the new process indicated an energy saving of 12.3% under same total number of trays and with a saving of the initial investment cost.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.3
• /
• pp.495-505
• /
• 2016

This study explores and selects an appropriate material that considers light and soft physical properties as well as activity for impact absorption pads that can be used to develop practical impact protective clothes worn during daily life by the elderly to reduce the impact of falls. Physical properties, impact absorption performance, and compression characteristics were evaluated on 5 types of foam, 2 types of 3D spacer fabric, and 3 types of polymer gel to select a material appropriate for the pad to be inserted into impact protective clothes. The evaluation of the physical properties showed that 3D spacer fabrics had lower density compared to other materials and polymer gels had the highest density. The elongation percentage was higher in foams than 3D spacer fabrics and EPDM foam had the highest elongation percentage. The impact absorption performance of honeycomb polymer gel was better than foams and 3D spacer fabrics. As a result of looking into compression energy and compression characteristics of materials, 'CR foam A' was found to absorb the largest amount of compression energy, 24.1%, among foams and polymer gels. A high energy absorption rate of 50.0% (or above) was indicated by 3D spacer fabrics; however, foams and polymer gels showed a progressive deformation of energy compression / recovery curve with 3D spacer fabrics that showed drastic deformation. Based on characteristics of materials, 'CR foam C' and EPDM with relatively high absorption performance can be used as protective pad materials among foams. Among polymer gels, 2 open-type polymer gels that have relatively low impact protective performance but a relatively lighter weight on human body (compared to closed-type) are considered appropriate protective pad materials.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.45-50
• /
• 2005

In this study, the casting/forging process was applied in manufacturing a low control arm, in order to prove that application of casting/forging process to Al6061 is likely to get the effect of light weight compared with existing steel products and to reduce the cost of materials. Firstly, In order to set up the optimum casting condition of the forging material, Al6061, casting experiments were carried out by controlling pouring temperature of the aluminum for casting, mold temperature, and pouring time. $700^{\circ}C$ pouring temperature, $300^{\circ}C$ mold temperature and 10-second pouring time were taken into account as the optimum casting conditions. With respect to a hot forging test, it is practiced on the basis of a temperature of materials, strain rate, and reduction rate so as to observe each microstructure and examine strain-stress curve simultaneously; examine tensile test and hardness test; eventually set up the optimum hot forging condition. A hot forging test, tensile test, hardness experiment, and microstructure observation were carried out on condition of $70\%$ reduction rate, $500^{\circ}C$ temperature of materials, and 1 strain rate. As a result of those experiments, 330MPa tensile strength, $16.4\%$ elongation, and 122.8Hv hardness were recorded. In oder to get a sound preform which has no unfitting cavity and less flash, two preforms were proposed on the basis of volume rate of the final product; the optimum volume rate of preform for the low control arm was $115\%$. In conclusion, it is confirmed that using the forging material rather than casting materials in casting/forging process is likely to get more superior mechanical properties. Compared with Al6061, performed by means of general forging, moreover, cast/forged Al6061 can not only stimulate productivity by reducing production processes, but cut down the cost of materials by reusing forging scraps.

• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.36-44
• /
• 1994

A fiber-optic temperature sensor utilizing InP as a sensing medium was implemented and tested to determine the dependance of the optical characteristics of InP on physical parameters for the use as design parameters in this type of sensors. The optical absorption coefficient of InP has been determined through the experimental measurement of the fundamental optical absorption characteristics at various temperature points. The transmission characteristics of light source at three temperature points($249^{\circ}K$, $298^{\circ}K$, $369^{\circ}K$) are computed from the optical absorption coefficient for a fixed length of InP. A series of measurement concluded that optical absorption edge moves to longer wavelength region at a speed of 0.42 nm / $^{\circ}K$ as the specimen gets hotter, and that increasing the thickness of the InP sensing layer shifts power density curve to lower temperature region.

• Structural Engineering and Mechanics
• /
• v.39 no.1
• /
• pp.125-145
• /
• 2011

Pushover analysis has gained significant popularity as an analytical tool for realistic determination of the inelastic behaviour of RC structures. Though significant work has been done to evaluate the demands realistically, the evaluation of capacity and realistic failure modes has taken a back seat. In order to throw light on the inelastic behaviour and capacity evaluation for the RC framed structures, a 3D Reinforced concrete frame structure was tested under monotonically increasing lateral pushover loads, in a parabolic pattern, till failure. The structure consisted of three storeys and had 2 bays along the two orthogonal directions. The structure was gradually pushed in small increments of load and the corresponding displacements were monitored continuously, leading to a pushover curve for the structure as a result of the test along with other relevant information such as strains on reinforcement bars at critical locations, failure modes etc. The major failure modes were observed as flexural failure of beams and columns, torsional failure of transverse beams and joint shear failure. The analysis of the structure was by considering all these failure modes. In order to have a comparison, the analysis was performed as three different cases. In one case, only the flexural hinges were modelled for critical locations in beams and columns; in second the torsional hinges for transverse beams were included in the analysis and in the third case, joint shear hinges were also included in the analysis. It is shown that modelling and capturing all the failure modes is practically possible and such an analysis can provide the realistic insight into the behaviour of the structure.

• Journal of Radiation Protection and Research
• /
• v.37 no.1
• /
• pp.10-15
• /
• 2012

Design and performance test results of a newly developed optically stimulated luminescence (OSL) measurement system are presented in this paper. Generally, different types of optical filters are used in OSL reader system to minimize the interference of the stimulation light in the OSL signal. For optically stimulation of $Al_2O_3:C$, we have arrived at an optimal combination of the filters, i.e., GG420 filter for filtering the stimulating light source, and a combined UG11 and BG39 filter at the detecting window (PMT). By using a high luminance blue LED (Luxeon V), sufficient luminous intensity could be obtained for optically stimulation. By using various control boards, the OSL reader device was successfully interfaced with a personal computer. A software was developed to deliver required commands to operate the OSL reader by using the LabView program (National Instruments, Inc.). In order to evaluate the reliability and the reproducibility of newly designed-OSL reader. Performance testing of the OSL reader was carried out for OSL efficiency, OSL decay curve and signal to noise ratio of the standard $Al_2O_3:C$ OSL material. It was found to be comparable with that of commercial Riso reader system.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.43 no.6
• /
• pp.715-722
• /
• 2010

The effects of temperature, salinity and irradiance on the growth of the harmful red tide dinoflagellate Cochlodinium polykrikoides Margelef isolated from the South Sea of Korea were examined in the laboratory. Growth was examined under the following combinations of temperature and salinity: 15, 20, 25 and $30^{\circ}C$, and 15, 20, 25, 30 and 35 psu at a constant irradiance of $180\;{\mu}mol/m^2/s$. No growth was observed with a temperature of $15^{\circ}C$ and a salinitiy of 15 psu. Moderate growth rates of more than 0.30 /day were obtained at $25^{\circ}C$ with salinities of 25.35 psu. These values are similar to in situ observations for this species. The maximum growth rate, 0.35 /day, was obtained at $25^{\circ}C$ and 30 psu. In light experiments, cell growth of C. polykrikoides was conducted with constant temperature ($20^{\circ}C$) and salinity (30 psu) under light photon flux densities (PFD) of 10, 25, 50, 70, 100, 150, 250 and $350\;{\mu}mol/m^2/s$. C. polykrikoides did not grow at $10\;{\mu}mol/m^2/s$. Cell growth was observed at irradiance values of $25\;{\mu}mol/m^2/s$ and above. The irradiance-growth curve was described as ${\mu}=0.30{\cdot}(I-15.27)/(I+27.22)$, (r=0.99). This suggests a compensation PFD of $15.27\;{\mu}mol/m^2/s$ and a maximum growth rate of 0.30 /day. In conclusion, C. polykrikoides prefers high salinity, temperature and irradiance in summer in Korea. These results provide important information for understanding the mechanism of C. polykrikoides blooms and developing technology to predict blooms of this organism in the field.