• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.145-149
• /
• 1997

STEP AP224 includes the information of machining feature and tolerances. Machining features are machined from raw material. Tolerance constrain feasible methods of manufacture, strongly influence the cost of manufacture. And tolerances influence the machining process. We need to decide the precedence between features .tool radius and tool direction for minimum tool changes. This paper deals with the method of decision of precedence between features and process parameters using feature information and tolerances in STEP AP224.

• Proceedings of the Safety Management and Science Conference
• /
• 2002.05a
• /
• pp.215-219
• /
• 2002

In this paper some physical evidences indicate that reduced friction occurs in an cryogenic machining process, in which LN2 is applied to the selected cutting zone. LN2 also reduced the tool wear rate to a great extent and elongated the tool life up to four times compared to emulsion cooling.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.188-192
• /
• 1994

This paper presenta new method for tool interference acoidance using rectanguar approximation in NC machining of scuptured surface. The procedure of algorithm for approximation of sculptured surface to rectangular surface is described. Using this algorithm, we can check concave, convex, and side interference region and avoid these interferenes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.67-72
• /
• 1994

Tool test was conducted to investigate the were process of only flank face TiN coated HSS tool in interrupted cutting for variuos cutting speeds and feed rates. Flank wear was caused by microchipping at the cutting edge. At high cutting speed, the which was formed as a result of diffusion and abrasion lowered cutting edge and influenced flank were. Flank wear due to chipping was little influenced by cutting speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.626-630
• /
• 1996

The most important problem in NC machining of a freeform mold surface is removal of tool interference. In this paper three methods are introduced to remove self-intersection on offsetted freeform surface for 3-axis NC. All methods are using intersectional offset curves on original offset surface. The fast method is sequential loop check using two lines which have two neighbor points of intersectional offset curves.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.507-508
• /
• 2007

IEC 61850은 변전소자동화시스템에 대한 국제 표준 규격이다. IEC 61850 파트 6은 통신관련 IED(Intelligent Electronic Device) 구성과 IED 파라미터, 통신 시스템 구성, 개폐소 구조 및 이들 간의 관계를 설명하는 파일 형식을 규정한다. 이 파일 형식의 주요 목적은 IED 능력 설명, 호환되는 방법으로 여러 제조사들의 IED 엔지니어링 도구와 시스템 엔지니어링 도구 간의 SA 시스템 설명을 교환하는 것이다. 본 논문에서는 XML을 이용한 IED Configurator TOOl 구현을 제시하였다.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2011.11a
• /
• pp.194-197
• /
• 2011

스마트 기기의 급격한 발전, 의료분야와 IT 기술의 융합, 소비자들의 높아지는 요구로 인해 8 비트 이하 마이크로 컨트롤러의 활용도가 높아질 전망이다. 이 논문에서는 EISC구조의 8 비트 마이크로 컨트롤러인 NH800의 ISA를 소개하고, 마이크로 컨트롤러를 위한 오픈소스 컴파일러인 SDCC에서 사용하는 ASxxxx Tool을 이용한 NH800 어셈블러 포팅을 제시한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.581-582
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.311-312
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.187-188
• /
• 2012