• Communications of the Korean Institute of Information Scientists and Engineers
• /
• v.2 no.1
• /
• pp.04-06
• /
• 1984

Representation of three dimensional objects on a CRT screen is usually done by means of a perspective view, hidden line removal enhances three dimensional effect and an algorithm based on existing methods is studied.Actual implementation was carried out on No.A 840 with Tektronix 4010 graphic display.

• Wind and Structures
• /
• v.25 no.6
• /
• pp.537-549
• /
• 2017

In this study, the turbulent flow around a bluff body for different wind velocities was investigated numerically by using its two- and three-dimensional models. These models were tested to verify the validity of the simulation by being compared with experimental results which were taken from the literature. Variations of non-dimensional velocities in different positions according to the bluff body height were analysed and illustrated graphically. When the velocity distributions were examined, it was seen that the results of both two- and three-dimensional models agree with the experimental data. It was also seen that the velocities obtained from two-dimensional model matched up with the experimental data from the ground to the top of the bluff body. Particularly, compared to the front part of the bluff body, results of the upper and back part of the bluff body are better. Moreover, after comparing the results from calculations by using different models with experimental data, the effect of multidimensional models on the obtained results have been analysed for different inlet velocities. The calculation results from the two-dimensional (2D) model are in satisfactory agreement with the calculation results of the three-dimensional model (3D) for various flow situations when comparing with the experimental data from the literature even though the 3D model gives better solutions.

• Journal of Mechanical Science and Technology
• /
• v.20 no.8
• /
• pp.1256-1265
• /
• 2006

The supersonic flows around tandem cavities were investigated by two-dimensional and three-dimensional numerical simulations using the Reynolds-Averaged Navier-Stokes (RANS) equation with the k- ω turbulence model. The flow around a cavity is characterized as unsteady flow because of the formation and dissipation of vortices due to the interaction between the freestream shear layer and cavity internal flow, the generation of shock and expansion waves, and the acoustic effect transmitted from wake flow to upstream. The upwind TVD scheme based on the flux vector split with van Leer's limiter was used as the numerical method. Numerical calculations were performed by the parallel processing with time discretizations carried out by the 4th-order Runge- Kutta method. The aspect ratios of cavities are 3 for the first cavity and 1 for the second cavity. The ratio of cavity interval to depth is 1. The ratio of cavity width to depth is 1 in the case of three dimensional flow. The Mach number and the Reynolds number were 1.5 and $4.5{\times}10^5$, respectively. The characteristics of the dominant frequency between two- dimensional and three-dimensional flows were compared, and the characteristics of the second cavity flow due to the first cavity flow was analyzed. Both two dimensional and three dimensional flow oscillations were in the 'shear layer mode', which is based on the feedback mechanism of Rossiter's formula. However, three dimensional flow was much less turbulent than two dimensional flow, depending on whether it could inflow and outflow laterally. The dominant frequencies of the two dimensional flow and three dimensional flows coincided with Rossiter's 2nd mode frequency. The another dominant frequency of the three dimensional flow corresponded to Rossiter's 1st mode frequency.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.1
• /
• pp.45-50
• /
• 2009

Three-dimensional, statistical-mechanical formulations of problems are usually untractable analytically, and therefore they are commonly solved numerically. However, their one-dimensional counterparts are always to be solved analytically. In general analytical solutions sheds more insights to the problems than numerical solutions. Hence, solutions of one-dimensional problems may provide key properties to the problems, when they are extended to three dimensions. In this article, thermodynamic properties of one-dimensional fluid comprising molecules of rigid rods are analyzed statistical-mechanically. Molecules of rigid rods are characterized with repulsive or excluded volume effect. It is observed that this feature is well reflected in thermodynamic functions such as Helmholtz free energy. volumetric equation of state. chemical potential, entropy, etc.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.12
• /
• pp.602-607
• /
• 2003

We show three-dimensional distribution of voltages resulted from the leakage current originated from outdoor electrical facilities in a submerged area. In case these facilities are grounded by the neutral line multiple grounding method, the existence of ungrounded electrical facilities can cause a disastrous effect on near-by passengers. In order to investigate this situation, we installed a real-scale test field for the experiment type I (for the leakage current path between a enclosure grounded electrical facility and another enclosure grounded one), and that for the experiment type II (for the leakage current path between a enclosure grounded electrical facility and another ungrounded one). For both cases, we carried out three-dimensional monitoring of the voltage distribution while varying additional conditions such as the exposure of the underground cables and the finishing of cable connection part. The result shows that a disastrous effect on human safety can arise from the leakage current without a pertinent measure for the construction and maintenance of outdoor electrical facilities.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.4
• /
• pp.29-32
• /
• 2004

Fully depleted Silicon-on-Insulator (FD-SOI) devices lead to better electrical characteristics than bulk CMOS devices. However, the presence of a thin top silicon layer and a buried SiO2 layer causes self-heating due to the low thermal conductivity of the buried oxide. The electrical characteristics of FDSOI devices strongly depend on the path of heat dissipation. In this paper, we present a new three-dimensional (3-D) analysis technique for the self-heating effect of the finger-type and bar-type transistors. The 3-D analysis results show that the drain current of the finger-type transistor is 14.7% smaller than that of the bar-type transistor due to the 3-D self-heating effect. We have learned that the rate of current degradation increases significantly when the width of a transistor is smaller that a critical value in a finger-type layout. The current degradation fro the 3-D structures of the finger-type and bar-type transistors is investigated and the design issues are also discussed.

• Geotechnical Engineering
• /
• v.12 no.1
• /
• pp.87-110
• /
• 1996

To simulate the three4imensional effect occurring near the tunnel face in a two -dimensional model, empirical load -dirtribution ratio concept is frequently used in tunnel design. In this paper, three -dimensional analysis is performed and its results are compared with those of two dimensional analysis'to investigate the applicability of the loadiistribution ratio concept. Especially, stress concentration near the tunnel face is investigated in depth. A parametric study is performed to investigate the effect of each factor on the load distribution ratio. The factors considered here include unsupported span length, initial stress, rock quality, tunnel size and the depth of tunnel location Moreover, the load -distribution ratios for the typical tunnel sections in Seoul Subway to be used in the tunnel design are suggested.

• 한국전산유체공학회:학술대회논문집
• /
• 1996.05a
• /
• pp.85-92
• /
• 1996

Numerical simulations are made for the three-dimensional flow around a wing in ground effect craft haying the complex geometry. A numerical tool is developed for the primary design of hull and wing shape of practical Wing-In-Ground effect(WIG) stop. The finite-difference method is utilized to descretize the governing equations and pressure field is obtained by using Marker-And-Cell(MAC) method. The air and water flows are simultaneously simulated in the time-marching solution procedure for the Navier-Stokes equation. The porosity technique and the density function are devised for the implementation of the three-dimensional body-boundary and the free-surface conditions, respectively. In this paper, a craft is modeled simply by three blocks containing a wing mounted on a main body horizontally, with the endplate. The numerical calculations of a WIG advancing in a calm water are performed and the WIG-generated wave profiles are also obtained. In the final paper, details of the numerical methods employed for the present study and calculated results are discussed.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4522-4533
• /
• 2022

For severe accident assessment of reactor pressure vessel (RPV), it is important to develop an accurate model that can predict transient thermo-mechanical behavior of the RPV lower head under the given condition. The present study revisits the lower head failure with two- and three-dimensional finite element models. In particular, we aim to give clear insight regarding the effect of the three-dimensionality present in the distribution of the thickness and thermal load of the lower head. For a rigorous validation of the result, both the OLHF-1 and the OLHF-2 tests are considered in this study. The result suggests that the three-dimensional effect is not negligible as far as the failure location is concerned. The non-uniformity of the thickness distribution is found to affect the failure location and time. The thermal load, which may not be axisymmetric in general, has the most significant effect on the failure assessment. We also observe that the creep property can affect the global deformation of the lower head, depending on the applied mechanical load.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.6
• /
• pp.37-45
• /
• 1998

In this paper, we report the first three-dimensional simulation result of the transient enhanced diffusion(TED) of dopants in the ion-implanted silicon by employing our 3D semiconductor process simulator, INPROS system. In order to simulate three-dimensional TED redistribution of dopants in silicon, the dopant distributions after the ion implantation was calculated by Monte Carlo(MC) method, followed by finite element(FE) numerical solver for thermal annealing. Excellent agreement between the simulated 3D profile and the SIMS data has been obtained for ion-implanted arsenic and phosphorus after annealing the boron marker layer at 75$0^{\circ}C$ for 2 hours. Our three-dimensional TED simulation could successfully explain the reverse short channel effect(RSCE) by taking the 3D point defect distribution into account. A coupled TED simulation and device simulation allows reverse short channel effect on threshold to be accurately predicted.