• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.171-181
• /
• 2003

The nose fairings of KSR-III are designed to be separated from the rocket by explosive force at the mission altitude to expose the payload. Adequate amount of separation force should be imposed to allow safe separation without collision between the fairings and the rocket, and the separation device was designed for the separation at very high altitude where almost no air load was expected. As the development of KSR-III goes on, several design changes have made and lower separation altitude of 45km is expected as a result. Under these circumstances, it is required to determine if the nose fairings can be separated without collision with much severer air load than for the design condition. In this study, the 6-DOF motion analysis program, PASEM, which was developed to predict the strap-on booster separation, is modified to simulate the pivotal motion of the fairings at early stages of separation. The accuracy of pivot motion simulation is validated by comparison with the results of ground test and the accurate separation conditions are deduced from it. Trajectory simulations are performed to see if separation without collision is possible with varying angle of attack, direction of gravity, and the effect of gust. It is also found that reducing the separation angle of the clamshell hinge from 60 degrees to 40 degrees can enhance separation safety and separation at lower altitude of 40km can be done without collision.

• Journal of Home Health Care Nursing
• /
• v.12 no.2
• /
• pp.1-15
• /
• 2005

Purpose: This study was conducted to assess the fall risk factors. Method: The subjects were 87 persons who were older than 65 years living at 28 nursing home in Seoul and Gyunggi province. Subjects were interviewed using RAFS II for intrinsic factor and the environmental factor were assessed using a structured questionnaire from Oct. to Dec. in 2004. The data were analyzed by SPSS(ver. 12.0) programs, using descriptive statistics, $x^2$-test, and t-test. Result: The 37.9% of the subjects experienced the fall, and its average number is $1.94\pm1.75$. The Women's experience of the fall was higher than that of the men, but it was no significant difference with gender. There was no significant difference with the age and duration of living. The mean of the intrinsic risk factor was 13.38 in total score 39 points marks on the RAFS II scales. The intrinsic risk factor score of the fallen group 15.71 was significantly higher than the non-fallen group 12.10. The variables of recent fall experience(t=4.72, p=0.000) and urinary dysfunction(t=2.64, p=0.010) was significantly higher than the non-fallen group. The highest variable of the intrinsic factor was the age and the variables of drug intake, balance, chronic disease, recent fall experience, urinary dysfunction were followed in order. The mean of the environmental risk factor was 0.24 points. No significant differences were shown in environmental risk factor between the fallen and the non-fallen groups. To the fallen group, the place of entrance was the highest risky environmental factor. To see in area dimension, the floor surfaces was the highest risky environmental factor and equipment and illumination factor was the following risky elements in order. In the total score of environmental risk factors based on the ares, the fallen group was 0.26 and the non-fallen group was 0.24, but there were no significant differences between the groups. Conclusion: This results suggested that visual protection strategy, set up the safety device in the place of entrance and inner stairway, bathroom and nonskid mat in the nursing home would be contribute to the prevention of the fall for the elderly.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.5 no.1
• /
• pp.64-76
• /
• 2003

This study was conducted in order to find out the basic data and informations for the accidents for repairing of agricultural machines. This study was summarized as fellows : 1. Among the total repair work, the ratio of repair accident was 68.9% and the accident ratio with power tiller, tractor, and combine was 84.8%. The accident occurred frequently in April to May and September to October because of frequent use of machines during this months. The accidents occurred often of ten to eleven and two to three afternoon in a day. 2. The 36.3% of the accident types was farming machines and the 60.4% of the accident occurred in yard of repair shop. The 34.4% of accident was caused by people, 26.2% by machines, 24.9% by environmental factors, and 14.5% by others. 3. In accident damage, human damage was 98.4% and economic damage was 43.6%. There was only 40.2% in having agricultural machinery insurance and 22.5% of research applicant answered that they would not have insurance in the future. 4. The 58.2% of the injured parts occurred in fingers, hands, wrists, or arms and the 74.4% of the damage types were bruise, prick or abrasion. The damaged parts of machinery were belt of power transmission device, chains, sharpened knives, narrow mechanism or cultivating knives for rotary. 5. The average days of medical treatment for casualty was 15.5 days and the average expense of medical treatment per person was 189,200 won. The days of temporary rest and the economic damage per person due to accident were 12.8 days and 469,300 won.

• Journal of agricultural medicine and community health
• /
• v.42 no.1
• /
• pp.13-23
• /
• 2017

Objectives: This study was conducted to evaluate a relationship between the blood concentrations of toxic metals and the blood pressure in people living near the copper smelter. Methods: The study included 570 adults living within 4km of the smelter. We compared systolic and diastolic blood pressure between tertiary groups for blood cadmium, mercury and lead levels, respectively. Multiple regression analysis was performed to identify risk factors affecting systolic and diastolic blood pressures. Results: In male subjects, there is a significant difference in the mean of systolic and diastolic blood pressure between tertiary groups of blood cadmium and mercury levels, but in women, there was no significant difference in the mean systolic and diastolic blood pressures in all tertiary groups of heavy metals. The results of multiple regression analysis showed that age, BMI, and cadmium concentration in men were risk factors for blood pressure. In women, age and BMI, drinking and smoking, and blood mercury were significantly influenced to blood pressure. Conclusions: Residents living near the Janghang smelter showed high concentrations of blood lead and cadmium, suggesting that they were exposed to high concentrations of heavy metals released from the smelter in the past. Such exposure may have caused some blood pressure increase. Especially, the concentration of cadmium in the case of men and the concentration of mercury in blood in the case of women were found to be significantly related to the increase of blood pressure. The local population should be advised to make efforts to reduce exposure to environmental contaminants, in order to minimize cardiovascular disease, and to pay close attention to any health problems possibly related to toxic metal exposure.

• Journal of Intelligence and Information Systems
• /
• v.17 no.4
• /
• pp.143-155
• /
• 2011

Lately electronic tagging policy for the sexual offenders was introduced in order to reduce and prevent sexual offences. However, most sexual offences against children happening these days are committed by the tagged offenders whose identities have been released. So, for the crime prevention, we need measures with which we could minimize the suffers more promptly and actively. This paper suggests a new system to relieve the sexual abuse related anxiety of the children and solve the problems that electronic bracelet has. Existing bracelets are only worn by serious criminals, and it's only for risk management and positioning, there is no way to protect the children who are the potential victims of sexual abuse and there actually happened some cases. So we suggest also letting the students(children) wear the LBS(Location Based Service) and USN(Ubiquitous Sensor Network) technology based electronic bracelets to monitor and figure out dangerous situations intelligently, so that we could prevent sexual offences against children beforehand, and while a crime is happening, we could judge the situation of the crime intelligently and take swift action to minimize the suffer. And by checking students' attendance and position, guardians could know where their children are in real time and could protect the children from not only sexual offences but also violent crimes against children like kidnapping. The overall system is like follows : RFID Tag for children monitors the approach of offenders. While an offender's RFID tag is approaching, it will transmit the situation and position as the first warning message to the control center and the guardians. When the offender is going far away, it turns to monitoring mode, and if the tag of the child or the offender is taken off or the child and offender stay at one position for 3~5 minutes or longer, then it will consider this as a dangerous situation, then transmit the emergency situations and position as the second warning message to the control center and the guardians, and ask for the dispatch of police to prevent the crime at the initial stage. The RFID module of criminals' electronic bracelets is RFID TAG, and the RFID module for the children is RFID receiver(reader), so wherever the offenders are, if an offender is at a place within 20m from a child, RFID module for children will transmit the situation every certain periods to the control center by the automatic response of the receiver. As for the positioning module, outdoors GPS or mobile communications module(CELL module)is used and UWB, WI-FI based module is used indoors. The sensor is set under the purpose of making it possible to measure the position coordinates even indoors, so that one could send his real time situation and position to the server of central control center. By using the RFID electronic roll book system of educational institutions and safety system installed at home, children's position and situation can be checked. When the child leaves for school, attendance can be checked through the electronic roll book, and when school is over the information is sent to the guardians. And using RFID access control turnstiles installed at the apartment or entrance of the house, the arrival of the children could be checked and the information is transmitted to the guardians. If the student is absent or didn't arrive at home, the information of the child is sent to the central control center from the electronic roll book or access control turnstiles, and look for the position of the child's electronic bracelet using GPS or mobile communications module, then send the information to the guardians and teacher so that they could report to the police immediately if necessary. Central management and control system is built under the purpose of monitoring dangerous situations and guardians' checking. It saves the warning and pattern data to figure out the areas with dangerous situation, and could help introduce crime prevention systems like CCTV with the highest priority. And by DB establishment personal data could be saved, the frequency of first and second warnings made, the terminal ID of the specific child and offender, warning made position, situation (like approaching, taken off of the electronic bracelet, same position for a certain time) and so on could be recorded, and the data is going to be used for preventing crimes. Even though we've already introduced electronic tagging to prevent recurrence of child sexual offences, but the crimes continuously occur. So I suggest this system to prevent crimes beforehand concerning the children's safety. If we make electronic bracelets easy to use and carry, and set the price reasonably so that many children can use, then lots of criminals could be prevented and we can protect the children easily. By preventing criminals before happening, it is going to be a helpful system for our safe life.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.1
• /
• pp.38-53
• /
• 2007

In a seminal judgment of November 2002 (Case C-476/98) relating to the compatibility with Community laws of the 'nationality clause' in the 1996 amending protocol to the 1955 U.S.-German Air Services Agreement, the European Court of Justice(ECJ) decided that the provision constituted a measure of an intrinsically discriminatory nature and was thus contrary to the principle of national treatment established under Art. 52 of the EC Treaty. The Court, rejecting bluntly the German government' submissions relying on public policy grounds(Art. 56, EC Treaty), seemed content to declare and rule that the protocol provision requiring a contracting state party to ensure substantial ownership and effective control by its nationals of its designated airlines had violated the requirement of national treatment reserved for other Community Members under the salient Treaty provision. The German counterclaims against the Commission, although tantalizing not only from the perusal of the judgment but from the perspective of international air law, were nonetheless invariably correct and to the point. For such a clause has been justified to defend the 'fundamental interests of society from a serious threat' that may result from granting operating licenses or necessary technical authorizations to an airline company of a third country. Indeed, the nationality clause has been inserted in most of the liberal bilaterals to allow the parties to enforce their own national laws and regulations governing aviation safety and security. Such a clause is not targeted as a device for discriminating against the nationals of any third State. It simply acts as the minimum legal safeguards against aviation risk empowering a party to take legal control of the designated airlines. Unfortunately, the German call for the review of such a foremost objective and rationale underlying the nationality clause landed on the deaf ears of the Court which appeared quite happy not to take stock of the potential implications and consequences in its absence and of the legality under international law of the 'national treatment' requirement of Community laws. Again, while US law limits foreign shareholders to 24.9% of its airlines, the European Community limits non-EC ownership to 49%, precluding any ownership and effective control by foreign nationals of EC airlines, let alone any foreign takeover and merger. Given this, it appears inconsistent and unreasonable for the EC to demand, $vis-{\grave{a}}-vis$ a non-EC third State, national treatment for all of its Member States. The ECJ's decision was also wrongly premised on the precedence of Community laws over international law, and in particular, international air law. It simply is another form of asserting and enforcing de facto extraterritorial application of Community laws to a non-EC third country. Again, the ruling runs counter to an established rule of international law that a treaty does not, as a matter of principle, create either obligations or rights for a third State. Aside from the legal problems, the 'national treatment' may not be economically justified either, in light of the free-rider problem and resulting externalities or inefficiency. On the strength of international law and economics, therefore, airlines of Community Members other than the designated German and U.S. air carriers are neither eligible for traffic rights, nor entitled to operate between or 'free-ride' on the U.S. and German points. All in all and in all fairness, the European Court's ruling was nothing short of an outright condemnation of established rules and principles of international law and international air law. Nor is the national treatment requirement justified by the economic logic of deregulation or liberalization of aviation markets. Nor has the requirement much to do with fair competition and increased efficiency.

• Journal of Korea Water Resources Association
• /
• v.54 no.11
• /
• pp.903-913
• /
• 2021

In the flood season, the measurement of the river discharge has many restrictions due to reasons such as budget, manpower, safety, convenience in measurement and so on. In particular, when heavy rain events occur due to typhoons, etc., it is difficult to measure the amount of flood due to the above problems. In order to improve this problem, in this study, a method was developed that can measure the river discharge in a flood season simply and safely in a short time with minimal manpower by combining the functions of a drone and a surface velocity doppler radar. To overcome the mechanical limitations of drones caused by weather issues such as wind and rainfall derived from the measurement of the river discharge using the conventional drone, we developed a drone with P56 grade dustproof and waterproof performance, stable flight capability at a wind speed of up to 36 km/h, and a payload weight of up to 10 kg. Further, to eliminate vibration which is the most important constraint factor in the measurement with a surface velocity doppler radar, a damper plate was developed as a device that combines a drone and a surface velocity Doppler radar. The velocity meter DSVM (Dron and Surface Veloctity Meter using doppler radar) that combines the flight equipment with the velocity meter was produced. The error of ±3.5% occurred as a result of measuring the river discharge using DSVM at the point of Geumsan-gun (Hwangpunggyo) located at Bonghwang stream (the first tributary stream of the Geum River). In addition, when calculating the mean velocity from the measured surface velocity, the measurement was performed using ADCP simultaneously to improve accuracy, and the mean velocity conversion factor (0.92) was calculated by comparing the mean velocity. In this study, the discharge measured by combining a drone and a surface velocity meter was compared with the discharge measured using ADCP and floats, so that the application and utility of DSVM was confirmed.

• Journal of Internet Computing and Services
• /
• v.17 no.1
• /
• pp.101-107
• /
• 2016

Due to the recent advancement in digital imaging technology, development of intervention equipment has become generalize. Video arbitration procedure is a process to insert a tiny catheter and a guide wire in the body, so in order to enhance the effectiveness and safety of this treatment, the high-quality of x-ray of image should be used. However, the increasing of radiation has become the problem. Therefore, the studies to improve the performance of x-ray detectors are being actively processed. Moreover, this intervention is based on the reference of the angiographic imaging and 3D medical image processing. In this paper, we propose a guidance system to support this intervention. Through this intervention, it can solve the problem of the existing 2D medical images based vessel that has a formation of cerebrovascular disease, and guide the real-time tracking and optimal route to the target lesion by intervention catheter and guide wire tool. As a result, the system was completely composed for medical image acquisition unit and image processing unit as well as a display device. The experimental environment, guide services which are provided by the proposed system Brain Phantom (complete intracranial model with aneurysms, ref H+N-S-A-010) was taken with x-ray and testing. To generate a reference image based on the Laplacian algorithm for the image processing which derived from the cerebral blood vessel model was applied to DICOM by Volume ray casting technique. $A^*$ algorithm was used to provide the catheter with a guide wire tracking path. Finally, the result does show the location of the catheter and guide wire providing in the proposed system especially, it is expected to provide a useful guide for future intervention service.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.7
• /
• pp.380-394
• /
• 2015

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2014. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of heat and mass transfer, cooling and heating, and air-conditioning, the flow inside building rooms, and smoke control on fire. Research issues dealing with duct and pipe were reduced, but flows inside building rooms, and smoke controls were newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for thermal contact resistance measurement of metal interface, a fan coil with an oval-type heat exchanger, fouling characteristics of plate heat exchangers, effect of rib pitch in a two wall divergent channel, semi-empirical analysis in vertical mesoscale tubes, an integrated drying machine, microscale surface wrinkles, brazed plate heat exchangers, numerical analysis in printed circuit heat exchanger. In the area of pool boiling and condensing, non-uniform air flow, PCM applied thermal storage wall system, a new wavy cylindrical shape capsule, and HFC32/HFC152a mixtures on enhanced tubes, were actively studied. In the area of industrial heat exchangers, researches on solar water storage tank, effective design on the inserting part of refrigerator door gasket, impact of different boundary conditions in generating g-function, various construction of SCW type ground heat exchanger and a heat pump for closed cooling water heat recovery were performed. (3) In the field of refrigeration, various studies were carried out in the categories of refrigeration cycle, alternative refrigeration and modelling and controls including energy recoveries from industrial boilers and vehicles, improvement of dehumidification systems, novel defrost systems, fault diagnosis and optimum controls for heat pump systems. It is particularly notable that a substantial number of studies were dedicated for the development of air-conditioning and power recovery systems for electric vehicles in this year. (4) In building mechanical system research fields, seventeen studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, and renewable energies, piping in the buildings. Proposed designs, performance performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the evaluation of work noise in tunnel construction and the simulation and development of a light-shelf system. The subjects of building energy were worked on the energy saving of office building applied with window blind and phase change material(PCM), a method of existing building energy simulation using energy audit data, the estimation of thermal consumption unit of apartment building and its case studies, dynamic window performance, a writing method of energy consumption report and energy estimation of apartment building using district heating system. The remained studies were related to the improvement of architectural engineering education system for plant engineering industry, estimating cooling and heating degree days for variable base temperature, a prediction method of underground temperature, the comfort control algorithm of car air conditioner, the smoke control performance evaluation of high-rise building, evaluation of thermal energy systems of bio safety laboratory and a development of measuring device of solar heat gain coefficient of fenestration system.

• Journal of Venture Innovation
• /
• v.4 no.2
• /
• pp.97-108
• /
• 2021

Labor contracts appear in form as an exchange relationship between labor products and wages, but since they transcend the level of simple barter, they can be economically identified as "trading" and can be identified as "rental." From a legal point of view, a legal device that legally supports and imposes binding force on commodity exchange relations is a contract. Such a labor contract led to a relationship in which wages were received and a certain amount of time was placed under the direction and supervision of the employer as a counter benefit to the receipt of wages. Since working hours are subordinate hours with one's labor under the disposition authority of the employer, long hours of work can be done for the health and safety of workers and furthermore, it can be an act that violates the value to enjoy as a human being. The reduction of working hours needs to be shortened in terms of productivity and enjoyment of workers' culture so that they can expand and reproduce, but users' corporate management labor and production activities should also be compatible compared to those pursued by capitalist countries. Working hours can be seen as individual time and time in society as a whole, and long hours of work at the individual level are reduced, which is undesirable at the individual level, but an increase in products due to an increase in production time at the social level can help social development. It is necessary to consider working hours in terms of finding the balance between these individual and social levels. If the regulation method of working hours was to regulate the total amount of working hours, flexibility and elasticity of working hours are a qualitative regulation method that allows companies to flexibly allocate and organize working hours within a certain range of up to 52 hours per week. Accordingly, it is necessary to shorten working hours, but expand and implement the flexible working hours system according to the situation of the company. To this end, it is necessary to flexibly operate the flexible working hours system, which is currently limited to six months, handle the selective working hours by agreement between employers and workers, and expand the target work of discretionary working hours according to the development of information and communication technology and new types based on the 4th industrial revolution.