• Journal of Korea Planning Association
• /
• v.54 no.4
• /
• pp.26-37
• /
• 2019

It is necessary to implement a wide range of housing welfare policies that citizens can experience in order to improve residents' the quality of life, as it emphasizes the balance of supply and management of public housing. The purpose of this study is to analyze the factors affecting residential satisfaction considering the three hierarchical levels of individual, household, and area. In the background of the study, the individuals' quality-of-life satisfaction determined not only by the individual but also by the various influencing environmental factors. This study targets 1,736 households, 3,239 persons in 464 areas in Seoul. The main research results are as follows. At the level one, there were influencing factors such as age(-), education level and income, and housing area per person, recipient of basic living(-), period(-) and RIR (at the level two). At the level three, west-south region(-) and social mix affect the complex of public housing. In consideration of living infrastructure, the closer to public transportation, public facilities, and medical facilities, the higher the satisfaction of public housing. The results of this analysis suggest that public support needs to focus on individual household members, but there is a need for ways to link it with the complex and the region.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.1
• /
• pp.32.1-32.1
• /
• 2021

We present the magnetic field strengths of CTA 102 using multi-frequency data at 2.6-343.5 GHz in order to study the physical origins of radio flares. The observations at 22 and 43 GHz were conducted using the single-dish radio telescopes of the Korean VLBI Network (KVN) from December 2012 until May 2018 (MJD 56200-58400). We used multi-frequency data obtained from the Effelsberg 100-m, OVRO 40-m, Metsähovi 14-m, IRAM 30-m, SMA, ALMA, and VLBA telescopes. During the period of the observations, two major flares (R1 and R2) are seen clearly at 15 and 37 GHz during MJD 57500-57800 and MJD 58000-58300, respectively. The source shows typical variability with time-scales ranging from 20-161 days at 15 GHz. The variability Doppler factor is in the range of 11.51-31.23. The quasi-simultaneous radio data are used to investigate the synchrotron spectrum of the source, finding that the synchrotron radiation is self-absorbed. The turnover frequency and the peak flux density of the synchrotron self-absorption (SSA) spectra are in ranges of 38.06-167.86 GHz and 1.49-10.38 Jy, respectively. From the SSA spectra, magnetic field strengths are estimated to be < 10 mG. The equipartition magnetic field strengths are larger than the SSA magnetic field strengths by a factor of > 100. This indicates that the radio flares may be related to a particle energy-dominated emission region.

• Transactions of Materials Processing
• /
• v.22 no.3
• /
• pp.133-142
• /
• 2013

Recently, electric vehicles and hybrid cars are being promoted as alternatives to reduce automobile emissions. Generally, thin sheet materials such as aluminum alloy AA300X and cold-rolled steel sheet such as JIS-G-3141 are used for the container for the lithium-ion secondary batteries. In this study, a multi-stage deep drawing process is used to produce a rectangular cup from thin stainless steel sheet material, SUS409L, with an initial blank thickness of 0.4mm for the battery container application. Numerical simulations of the first through the fifth stages for the multi-stage deep drawing with thin SUS409L sheet were conducted using LS-Dyna3D Implicit/Explicit. Special consideration was given to the deformation characteristics due to the normal anisotropy of the sheet material. The numerical simulations were conducted with both isotropic properties and the anisotropic properties of the initial blank material. An unexpected forming failure, barreling in the bottom region of the deep drawn rectangular cup, was observed. This failure mode can be avoided by additional ironing thickness control during the process.

• The KIPS Transactions:PartB
• /
• v.11B no.7 s.96
• /
• pp.841-848
• /
• 2004

Evolutionary a1gorithms are well-suited for multi-objective optimization problems involving several, often conflicting objectives. Pareto-based evolutionary algorithms, in particular, have shown better performance than other multi-objective evolutionary algorithms in comparison. However, generalized evolutionary multi-objective optimization algorithms have a weak point, in which the distribution of solutions are not uni-formly distributed onto Pareto optimal front. In this paper, we propose an evolutionary a1gorithm for multi-objective optimization which uses seed individuals in order to overcome weakness of algorithms Published. Seed individual means a solution which is not located in the crowded region on Pareto front. And the idea of our algorithm uses seed individuals for reproducing individuals for next generation. Thus, proposed a1go-rithm takes advantage of local searching effect because new individuals are produced near the seed individual with high probability, and is able to produce comparatively uniform distributed pareto optimal solutions. Simulation results on five testbed problems show that the proposed algo-rithm could produce uniform distributed solutions onto pareto optimal front, and is able to show better convergence compared to NSGA-II on all testbed problems except multi-modal problem.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.1
• /
• pp.3-11
• /
• 2005

Using various thermo-mechanical schedules characterized by varying reheating temperature, deformation temperature and strain, the austenite recrystallization and ferrite refinement of a Nb bearing low carbon steel(0.15C-0.25Si-1.11Mn-0.04Nb) were investigated. For single pass heavy deformations at $800^{\circ}C$, the 40% deformed austenite was not recrystallized while the 80% deformed one was fully recrystallized. Ferrite grains formed in the 80% deformed specimen was not very small compared with those in the 40% deformed specimen, which implied the recrystallized austenite was not more beneficial to ferrite refinement than the non-recrystallized one. In case of deformation in low temperature austenite region, a multi-pass deformation made finer ferrites than a single-pass deformation, as the total reduction was the same, due to more ferrite nucleation sites in the non-recrystallization of austenite for multi-pass deformation. When specimen was deformed at $775^{\circ}C$ that was $10^{\circ}C$ higher than $Ar_3$, the ferrite of about $1{\mu}m$ was formed through deformation induced ferrite transformation(DIFT), and the amount of ferrite was increased with increasing reduction. Dislocation density was very high and no carbides were observed in DIFT ferrites, presumably due to supersaturated carbon solution. By deformation in two phase(50% austenite+50% ferrite) region the very refined ferrite grains of less than $1{\mu}m$ were formed certainly by recovery and recrystallization of deformed ferrites and, a large portion of ferrites were divided by subgrain boundaries with misorientation angles smaller than 10 degrees.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.709-711
• /
• 1999

In this paper, Fuzzy Logic Controller was Designed for the Degree control of Arago's disk system. Arago's disk system is an application of Arago's disk phenomenon which is the operating principle of induction motor. Since the Arago's disk system varies to stable region. maginally stable region, unstable region according to the degree of bar respectively, it is a sutable system which can be evaluate an efficiency of the system. While an existing controller which was designed using linearized system modeling could control the system on only one operating point, fuzzy logic controller has the advantage in showing good response for multi-operating points because it does not need system modeling.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.60.1-60.1
• /
• 2014

The star ${\zeta}$ Ophiuchi (HD 149757) is one of the brightest massive stars in the northern hemisphere and was widely studied in various wavelength domains. We report the analysis results of far ultraviolet (FUV) observations with other wavelengths for around ${\zeta}$ Ophiuchi. We study the correlation of between multi wavelength observations. We have developed a Monte Carlo code that simulates dust scattering of light including multiple encounters. The code is applied to the present Oph HII region to obtain the geometrical information of dust such as distance and thickness. Also We apply three-dimensional photoionization code to model Wisconsin $H{\alpha}$ Mapper observations of the H II region surrounding the star.

• Journal of the Korean housing association
• /
• v.6 no.2
• /
• pp.69-76
• /
• 1995

Recent opening of the era of local government and management randers study tasks concerning the improvement of the housing conditions by improving the problems in the residential conditions of the cheju Island region so as to help improve the life qualities of this legion make the area as an international resort place, and thus develop the indentify in the heat of the people in this region. The suggestions based on the study for the improvement of housing environment are summarized as follows: (1) To improve the collective housing. housing construction plan shall b made in harmony with the skylines of the Hanra mountain alongside the East-West rides across the long diameter of the oval shape of the Island, which includes 1) the construction of housing complex in harmony with and taking advantage of the natural scene of the area. and 2) the construction of variable housing readjustable in accordance with each family structure of variable housings for multi-families, which are believed not to provide quality housing conditions. Shall be entrained. (2) Encouraging the construction of detached house : 1) construction of housings in which three generations can reside together according to the traditional family structure in the region. 2) construction of the pastoral housings. 3) construction of tenement housings partitioned for each two families. 4) development of sliver town in the rural area. (3) Using the construction mateials produced in the Cheju I land will help promote the development of identity in the heart of the people in this region.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.85.2-85.2
• /
• 2012

In this paper, we introduce the 3D modeling of the coronal magnetic field in the solar active region by extrapolating from the 2D observational data numerically. First, we introduce a nonlinear force-free field (NLFFF) extrapolation code based on the MHD-like relaxation method implementing the cleaning a numerical error for Div B proposed by Dedner et al. 2002 and the multi-grid method. We are able to reconstruct the ideal force-free field, which was introduced by Low & Lou (1990), in high accuracy and achieve the faster speed in the high-resolution calculation (512^3 grids). Next we applied our NLFFF extrapolation to the solar active region NOAA 10930. First of all, we compare the 3D NLFFF with the flare ribbons of Ca II images observed by the Solar Optical Telescope (SOT) aboard on the Hinode. As a result, it was found that the location of the two foot-points of the magnetic field lines well correspond to the flare ribbon. The result indicates that the NLFFF well capture the 3D structure of magnetic field in the flaring region. We further report the stability of the magnetic field by estimating the twist value of the field line and finally suggest the flare onset mechanism.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.509-516
• /
• 2008

Multi-layer circuit card for semiconductor inspection was fabricated by LTCC technology. After a proper impedance design without electrical interference, ceramic tapes with the composition of $CaO-Al_2O_3-SiO_2-B_2O_3$ glass and $Al_2O_3$ were prepared. The electrode with silver paste printed on the tape. Printed ceramic sheets were then laminated and sintered. Densities and dielectric properties were measured. The microstructure, fracture surface of the region of via and matching state of substrate-electrode were observed. The durability of plated outside electrode were examined by hardness and scratch test.