• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.21-31
• /
• 2007

Relaxed Static Stability (RSS) concept has been applied to improve aerodynamic performance of modern version supersonic jet fighter aircraft. The T-50 advanced supersonic trainer employs the RSS concept in order to improve the aerodynamic performance. And the flight control system stabilizes the unstable aircraft and provides adequate handling qualities. The T-50 longitudinal control laws employ a proportional-plus-integral type controller based on a dynamic inversion method. The longitudinal dynamic modes consist of short period with high frequency and phugoid mode with low frequency. The design goal of longitudinal control law is optimization of short period damping ratio and frequency using Lower Order Equivalent System (LOES) complying the requirement of MIL-F-8785C. This paper addresses phugoid mode characteristics such as damping ratio and natural frequency that is affected by the nonlinear control laws such as angle of attack limiter, auto pitch attitude command system and autopilot of pitch attitude hold.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.248-255
• /
• 2021

The main causes of the July 2013 OZ 214 accident were poorly performed approach and the failure to recognize the autothrottle in the HOLD position which the automated speed control was not provided. The pilots late decision for go-around was also a critical factor leading to the accident. The B777 POM restricts the use of FLCH mode beyond the FAF. This research utilized the QAR data of an airline's B777 fleet in the period of two years where 44 cases were found. In many cases, the FLCH mode was used for rapid descent from an higher than normal situation. In addition, in the base turn, continuous use of FLCH mode even when the path was below the glide path were observed. Airports with elevation above 500 ft MSL had a higher rate of occurrence. In this research, the proper descent planning and vertical path monitoring, and the adherence to the limitation set in the manuals and the stabilized approach criteria were re-emphasized as mitigation to reduce event occurences.

• Korean Journal of Metals and Materials
• /
• v.50 no.2
• /
• pp.136-145
• /
• 2012

Resistance spot welding of TRIP780 steels was investigated to enhance understanding of weld fracture mode after tensile shear testing (TST) and L-shape tensile testing (LTT). The main failure mode for spot welds of TRIP780 steels was partial interfacial fracture (PIF). Although PIF does not satisfy the minimum button diameter (4${\surd}$t) for acceptable welds, it shows enough load carrying capacity of resistance spot welds for advanced high strength steels. In the analysis of displacement controlled L-shape tensile test results, cracks initiated at the notch of the faying surface and propagated through the interface of weldments, and finally, cracks change path into the sheet thickness direction. Use of the ductility ratio and CE analysis suggested that the occurrence of PIF is closely related to high hardness and brittle welds, which are caused by fast cooling rates and high chemical compositions of TRIP steels. Analysis of the hold time and weld time in a welding schedule demonstrated that careful control of the cooling rate and the size of a weld nugget and the HAZ zone can reduce the occurrence of PIF, which leads to sound welds with button fractures (BFs).

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.1
• /
• pp.31-42
• /
• 2009

Common structural rule (CSR) doesn' t provide any other specific regulations for permanent means of access (PMA) platform structure in a cargo oil tank. The PMA platform is recommended to comply with scantling requirement of local support member. However, it leads to too conservative scantlings compared with actual loads imposed on the platform. This paper proposes a strength assessment procedure for the PMA structure based on a nonlinear ultimate strength. The ultimate strength is evaluated in a sufficiently conservative way. The first linear buckling mode is used as an initial imperfection shape and its magnitude is determined using the definitions of DNV PULS. Since the same imperfection mode as the failure mode of the ultimate limit state is assumed, it can accelerate the failure. Au ultimate strength capacity curve obtained from a series of nonlinear FE analysis is compared with actual stresses calculated by CSR cargo hold analysis.