• International Journal of Aeronautical and Space Sciences
• /
• 제8권1호
• /
• pp.21-31
• /
• 2007

Relaxed Static Stability (RSS) concept has been applied to improve aerodynamic performance of modern version supersonic jet fighter aircraft. The T-50 advanced supersonic trainer employs the RSS concept in order to improve the aerodynamic performance. And the flight control system stabilizes the unstable aircraft and provides adequate handling qualities. The T-50 longitudinal control laws employ a proportional-plus-integral type controller based on a dynamic inversion method. The longitudinal dynamic modes consist of short period with high frequency and phugoid mode with low frequency. The design goal of longitudinal control law is optimization of short period damping ratio and frequency using Lower Order Equivalent System (LOES) complying the requirement of MIL-F-8785C. This paper addresses phugoid mode characteristics such as damping ratio and natural frequency that is affected by the nonlinear control laws such as angle of attack limiter, auto pitch attitude command system and autopilot of pitch attitude hold.

• 한국항행학회논문지
• /
• 제25권3호
• /
• pp.248-255
• /
• 2021

2013년 7월 아시아나 OZ 214편 샌프란시스코 국제공항 (SFO) 사고의 주요 원인은 조종사의 잘못된 접근 조작과 항공기 오토트로틀 홀드(autothrottle hold) 모드로 인해 자동 속도 컨트롤(control)이 불가함을 인지 못하였고, 복행 (go-around) 결심이 늦었다는 것이다. 이와 관련하여 B777 POM (pilot operation manual)에는 FAF (final approach fix) 후 FLCH (flight level change) 모드 사용을 제한하고 있다. 본 연구는 QAR (quick access recorder) 데이터 분석 시스템을 활용하여 국내 항공사의 B777 기종에서 2년간 발생한 44건의 해당 이벤트를 분석 한 결과, 정상 강하각 보다 높은 위치에서 조종사가 FLCH 모드를 이용하여 급하게 강하하는 과정에서 해당 이벤트들이 주로 발생하였으며, 항공기 베이스 선회 (base Turn) 시 정상 수직 경로(vertical path)보다 낮은 상태에서도 FLCH 모드를 지속 사용한 예도 있었다. 아울러 공항의 표고가 500 ft 이상의 높은 공항에서 이벤트 발생율이 높은 점을 확인하였다. 이에 본연구에서는 항공기 접근 시의 강하 계획(descent planning), 수직 경로(vertical path) 모니터링의 중요성과 자동항법장치 사용 기준 및 안정 접근 항목(stabilized approach criteria)의 준수로 이벤트 경감방안 마련의 시사점을 도출하고자 한다.

• 대한금속재료학회지
• /
• 제50권2호
• /
• pp.136-145
• /
• 2012

Resistance spot welding of TRIP780 steels was investigated to enhance understanding of weld fracture mode after tensile shear testing (TST) and L-shape tensile testing (LTT). The main failure mode for spot welds of TRIP780 steels was partial interfacial fracture (PIF). Although PIF does not satisfy the minimum button diameter (4${\surd}$t) for acceptable welds, it shows enough load carrying capacity of resistance spot welds for advanced high strength steels. In the analysis of displacement controlled L-shape tensile test results, cracks initiated at the notch of the faying surface and propagated through the interface of weldments, and finally, cracks change path into the sheet thickness direction. Use of the ductility ratio and CE analysis suggested that the occurrence of PIF is closely related to high hardness and brittle welds, which are caused by fast cooling rates and high chemical compositions of TRIP steels. Analysis of the hold time and weld time in a welding schedule demonstrated that careful control of the cooling rate and the size of a weld nugget and the HAZ zone can reduce the occurrence of PIF, which leads to sound welds with button fractures (BFs).

• 대한조선학회논문집
• /
• 제46권1호
• /
• pp.31-42
• /
• 2009

Common structural rule (CSR) doesn' t provide any other specific regulations for permanent means of access (PMA) platform structure in a cargo oil tank. The PMA platform is recommended to comply with scantling requirement of local support member. However, it leads to too conservative scantlings compared with actual loads imposed on the platform. This paper proposes a strength assessment procedure for the PMA structure based on a nonlinear ultimate strength. The ultimate strength is evaluated in a sufficiently conservative way. The first linear buckling mode is used as an initial imperfection shape and its magnitude is determined using the definitions of DNV PULS. Since the same imperfection mode as the failure mode of the ultimate limit state is assumed, it can accelerate the failure. Au ultimate strength capacity curve obtained from a series of nonlinear FE analysis is compared with actual stresses calculated by CSR cargo hold analysis.