• Steel and Composite Structures
• /
• v.25 no.3
• /
• pp.299-314
• /
• 2017

The aim of this paper is to investigate the performance of Lightweight Aggregate Concrete Filled Steel Tube (LWCFST) columns experimentally and compare to the behavior of Self-Compacted Concrete Filled Steel Tube (SCCFST) columns under axial loading. Four different L/D ratios and three D/t ratios were used in the experimental program to delve into the compression behaviours. Compressive strength of the LWC and SCC are 33.47 MPa and 39.71 MPa, respectively. Compressive loading versus end shortening curves and the failure mode of sixteen specimens were compared and discussed. The design specification formulations of AIJ 2001, AISC 360-16, and EC4 were also assessed against test results to underline the performance of specification methods in predicting the compression capacity of LWCFST and SCCFST columns. Based on the behaviour of the SCCFST columns, LWCFST columns exhibited different performances, especially in ductility and failure mode. The nature of the utilized lightweight aggregate led to local buckling mode to be dominant in LWCFST columns, even the long LWCFST specimens suffered from this behaviour. While with the SCCFST specimens the global buckling governed the failure mode of long specimens without any loss in capacity. Considering a wide range of column geometries (short, medium and long columns), this paper extends the current knowledge in composite construction by examining the potential of two promising and innovative structural concrete types in CFST applications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2261-2266
• /
• 2011

Being the most widely used in ultrasound Doppler color flow mapping, the Kasai algorithm, also known as lag-1 autocorrelation method, is capable of estimating the Doppler mean frequency relatively accurately with a modest amount of computation. Particularly in the case of imaging deep lying areas, however, its performance suffers due to low signal-to-noise ratios. The purpose of this paper is to propose a dealiased lag-2 autocorrelation method which is superior to the Kasai algorithm even at low signal-to-noise ratios and to compare their performances through simulations. The proposed algorithm is found to be better by about 2 to 3 dB than the Kasai algorithm in terms of Doppler mean frequency estimation error in the presence of measurement noise.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1571-1576
• /
• 2013

This paper proposes an improvement algorithm of signal-to-noise ratios (SNRs) for speech signals under noisy environments. The proposed algorithm first estimates the SNRs in a low SNR, mid SNR and high SNR areas, in order to improve the SNRs in the speech signal from background noise, such as white noise and car noise. Thereafter, this algorithm subtracts the noise signal from the noisy speech signal at each bands using a spectrum sharpening method. In the experiment, good signal-to-noise ratios (SNR) are obtained for white noise and car noise compared with a conventional spectral subtraction method. From the experiment results, the maximal improvement in the output SNR results was approximately 4.2 dB and 3.7 dB better for white noise and car noise compared with the results of the spectral subtraction method, in the background noisy environment, respectively.

• Journal of The Korean Astronomical Society
• /
• v.23 no.1
• /
• pp.1-13
• /
• 1990

New uvby photoelectric photometry was carried out for a $\delta$ Scuti variable, HR1170. By applying the Fourier method and the linear least square method, three frequencies were derived: $f_1=10.06134c/d$ ($P_1=0.^d0994$). $f_2=11.91754c/d$ ($P_2=0.^d0839$). $f_3=18.96776c/d$ ($P_3=0.^d0527$). From the observed pulsational constants and from the phase difference and amplitude ratios for color(b-y) and magnitude y. three different pulsation modes (n, l) of $f_1(0,0)$, $f_2(1,2)$, $f_3(3,2)$ are deduced, indicating the existence of nonradial mode in HR1170. Some physical parameters indicate that HR1170 is evolving at the stage of H-shell burning.

• Food Science of Animal Resources
• /
• v.33 no.1
• /
• pp.125-132
• /
• 2013

In the present study, to determine the effects of terminal sire strains, carcass characteristics, yields of retail cut, and meat quality of 425 pigs were examined. Terminal sires were divided into five strains (D1, D2, B1, B2, and BD) based on the countries of origin and breeds. The strains D1 and D2 showed high grade 1+ appearance ratios and strains B1, B2, and D1 showed high appearance ratios of carcass yield grade A. As for the real retail cut yields of meat, strain D1 showed large real retail cut yields of meat in shoulder, rib, fore leg, loin, belly, tenderloin and hind leg. Moisture contents were significantly higher in strain B1, and protein and fat contents were significantly higher for strain D1 than in the other strains (p<0.05). Shear force values were significantly higher for strain B1 than in the other strains (p<0.05). For meat color properties, the lightness were significantly higher in strains D1, D2, and BD, and the yellowness were significantly higher in strains D1, D2, and BD relative to the other strains (p<0.05). In sensory evaluation, drip of strains D1 and D2 were significantly lower while marbling and overall acceptability were significantly higher in the other four strains (p<0.05). Therefore, when considering the results of the present study comprehensively, using strains D1 and D2 that showed high grade 1+ appearance ratios, large real retail cut yields of belly, significantly higher lightness and sensory evaluation will be helpful to the incomes of producers and farm households.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.4
• /
• pp.600-607
• /
• 2014

The aim of this study was to assess the effect of substrate to inoculum ratio (S/I ratio) on the biochemical methane potential (BMP) and anaerobic biodegradability ($D_{deg}$) of different piggery slaughterhouse wastes, such as piggery blood, intestine residue, and digestive tract content. These wastes were sampled from a piggery slaughterhouse located in Kimje, South Korea. Cumulative methane production curves for the wastes were obtained from the anaerobic batch fermentation having different S/I ratios of 0.1, 0.5, 1.0, and 1.5. BMP and anaerobic biodegradabilities ($D_{deg}$) of the wastes were calculated from cumulative methane production data for the tested conditions. At the lowest S/I ration of 0.1, BMPs of piggery blood, intestine residue, and digestive tract content were determined to be 0.799, 0.848, and $1.076Nm^3kg^{-1}-VS_{added}$, respectively, which were above the theoretical methane potentials of 0.539, 0.644, and $0.517Nm^3kg^{-1}-VS_{added}$ for blood, intestine residue, and digestive tract content, respectively. However, BMPs obtained from the higher S/I ratios of 0.5, 1.0, and 1.5 were within the theoretical range for all three types of waste and were not significantly different for the different S/I ratios tested. Anaerobic biodegradabilities calculated from BMP data showed a similar tendency. These results imply that, for BMP assay in an anaerobic reactor, the S/I ratio of anaerobic reactor should be above 0.1 and the inoculum should be sufficiently stabilized to avoid further degradation during the assay.

• Asian-Australasian Journal of Animal Sciences
• /
• v.7 no.4
• /
• pp.555-561
• /
• 1994

This paper presents results from a study of the body composition and sensory characteristics of female weaner goat meat. A completely randomized $3{\times}3{\times}2$ factorial design was used. Factors were genotype (Thai native; TN, 75% TN $\times$ 25% Anglo-Nubian; AN and 50% TN $\times$ 50% AN), feeding {grazing only, low (1.0% BW/d) and high (1.5% BW/d) concentrate supplementation and parasite control (undrenched and drenched)}. It was shown that there was no effect of genotype on body components and dressing percentage. However, TN and 75% TN $\times$ 25% AN kids had significantly (p<0.05) higher muscle to bone ratios (4.20% and 4.20%, respectively) compared with 50% TN $\times$ 50% AN kids (3.88%). Kids on grazing only had significantly (p<0.01) higher muscle percentage (64.12%) than did kids in low (61.30%) and high (60.62%) supplementary feeding program, but there was no significant (p>0.05) difference between low and high supplementary feeding groups. Kids offered supplementary feeding had significantly (p<0.01) higher percentages of total fat, intermuscular fat, pelvic fat and kidney fat than those of grazing only. Kids offered supplementary feeding had significantly (p<0.05) higher muscle to bone ratios and significantly (p<0.01) higher muscle plus fat to bone ratios compared with those of grazing only. This may be due to significantly lower (p<0.01) bone contents (14.95, 14.17 and 16.8% for kids offered low and high supplementary feeding and grazing only, respectively. There was no significant difference in sensory characteristics of goat meat between genotypes or feeding groups.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.477-488
• /
• 2022

Pile composite foundation (PCF) has been commonly applied in practice. Existing research has focused primarily on semi-infinite media having equal pile lengths with little attention given to the effects of inclined bedrock and dissimilar pile lengths. This investigation considers the effects of inclined bedrock on vertical loaded PCF with dissimilar pile lengths. The pile-soil system is decomposed into fictitious piles and extended soil. The Fredholm integral equation about the axial force along fictitious piles is then established based on the compatibility of axial strain between fictitious piles and extended soil. Then, an iterative procedure is induced to calculate the PCF characteristics with a rigid cap. The results agree well with two field load tests of a single pile and numerical simulation case. The settlement and load transfer behaviors of dissimilar 3-pile PCFs and the effects of inclined bedrock are analyzed, which shows that the embedded depth of the inclined bedrock significantly affects the pile-soil load sharing ratios, non-dimensional vertical stiffness N₀/wdE_s, and differential settlement for different length-diameter ratios of the pile l/d and pile-soil stiffness ratio k conditions. The differential settlement and pile-soil load sharing ratios are also influenced by the inclined angle of the bedrock for different k and l/d. The developed model helps better understand the PCF characteristics over inclined bedrock under vertical loading.

• The Korean Journal of Zoology
• /
• v.7 no.1
• /
• pp.6-8
• /
• 1964

1. A total of 260 individuals of carp was collected from Nakdong and Hyungsan Rivers. 2. The normal dental form of carp is 3, 1, 1-1, 1, 3, but the author observed abnormal dental forms (3, 2 or 1, 1, (+1)-1, 1 or 2, 3). 3. Variation ratios of dental forms are : A. Normal form; 3, 1, 1-1, 1, 3..........88.85% B. Abnormal forms; a. 3, 2, 1-1, 1 or 2, 3..........2.31% b. 3, 1, 1, 1-1, 1 or 2, 3..........5.00% c. 3, 2, 1, 1-1, 1 or 2, 3..........3.07% d. with 2 or 3 bone processes..........0.77% 4. The ratios among the length of first row (I), length of second tooth in first row ($I_{-2}$) and mid line(M) are as follows; 5. The growth of bone process beside second row tooth is not concerned with the body growth. 6. The number of the groove on second tooth in first row increases according to the growth of body.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.3
• /
• pp.64-67
• /
• 2008

This study investigated the influence of composite resins with different elastic moduli and occlusal loading conditions on the stress distribution of restored notch-shaped non-carious cervical lesions (NCCL) using 3D finite element analysis. Two different materials, Tetric Flow and Z100, were used as representative flowable hybrid resins for the restoration of NCCL. A static point load of 500 N was applied at the buccal and palatal cusps. The ratios of stress reduction to energy dissipation were better in the compressive state than the tensile state regardless of the restorative material. The total dissipation ratios for Tetric Flow were 1.5% and 4.2% larger than those for Z100 under compression and tension, respectively. Therefore, tensile stress poses more of a risk for tooth fracture, and Tetric Flow is a more appropriate material for restoration.