• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.247-252
• /
• 2001

The flow around free end of a finite circular cylinder(FC) embedded in an atmospheric boundary layer has been investigated experimentally. The experiments were carried out in a closed-return type subsonic wind tunnel with varying aspect ratio of the finite cylinder mounted vertically on a flat plate. The wake structures behind a 2-D cylinder and a finite cylinder located in a uniform flow were also measured for comparison. Reynolds number based on the cylinder diameter was about Re=20,000. A hot-wire anemometer was employed to measure the wake velocity and the mean pressure distributions on the cylinder surface were also measured. The flow past the FC free end shows a complicated three-dimensional wake structure and flow phenomenon is quite different from that of 2-D cylinder. The three-dimensional flow structure was attributed to the downwashing counter rotating vortices separated from the FC free end. As the FC aspect ratio decreases, the vortex shedding frequency is decreased and the vortex formation length is increased compared to that of 2-D cylinder. Due to the descending counter-rotating twin-vortex, in the region near the FC free end, regular vortex shedding from the cylinder is suppressed and the vortex formation region is hardly established. In the wake center region, the mean velocity for the FC located in atmospheric boundary layer has large velocity deficit, compared to that of uniform flow.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.12
• /
• pp.1821-1830
• /
• 2001

The flow around free end of a finite circular cylinder (FC) embedded in an atmospheric boundary layer has been investigated experimentally. The experiments were carried out in a closed-return type subsonic wind tunnel with varying aspect ratio of the finite cylinder mounted vertically on a flat plate. The wakes behind a 2-D cylinder and a finite cylinder located in a uniform flow were measured for comparison. Reynolds number based on the cylinder diameter was about Re=20,000. A hot-wire anemometer was employed to measure the wake velocity and the mean pressure distributions on the cylinder surface were also measured. The flow past the FC free end shows a complicated three-dimensional wake structure and flow phenomenon is quite different from that of 2-D cylinder. The three-dimensional flow structure was attributed to the downwashing counter rotating vortices separated from the FC free end. As the FC aspect ratio decreases, the vortex shedding frequency decreases and the vortex formation length increases compared to that of 2-D cylinder. Due to the descending counter-rotating twin-vortex, near the FC free end, regular vortex shedding from the cylinder is suppressed and the vortex formation region is hardly distinguished. Around the center of the wake, the mean velocity for the FC located in atmospheric boundary layer has large velocity deficit compared to that of uniform flow.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.12
• /
• pp.1742-1747
• /
• 2012

A total of 96 growing pigs ((Landrace${\times}$Yorkshire)${\times}$Duroc; BW = $26.58{\pm}1.41$ kg) were used in a 6-wk feeding trail to evaluate the effects of fermented chlorella (FC) supplementation on growth performance, nutrient digestibility, blood characteristics, fecal microbial and fecal noxious gas content in growing pigs. Pigs were randomly allotted into 1 of 4 dietary treatments with 6 replicate pens (2 barrows and 2 gilts) per treatment. Dietary treatments were: i) negative control (NC), basal diet (without antibiotics); ii) positive control (PC), NC+0.05% tylosin; iii) (fermented chlorella 01) FC01, NC+0.1% FC, and iv) fermented chlorella 02 (FC02), NC+0.2% FC. In this study, feeding pigs PC or FC01 diets led to a higher average daily gain (ADG) and dry matter (DM) digestibility than those fed NC diet (p<0.05), whereas the inclusion of FC02 diet did not affect the ADG and DM compared with the NC group. No difference (p>0.05) was observed on the body weight, average daily feed intake (ADFI), gain:feed (G:F) ratio, the apparent total tract digestibility of N and energy throughout the experiment. The inclusion of PC or FC did not affect the blood characteristics (p>0.05). Moreover, dietary FC treatment led to a higher (p<0.05) lactobacillus concentration and lower E. coli concentration than the NC treatment, whereas the antibiotic supplementation only decreased the E. coli concentration. Pigs fed FC or PC diet had reduced (p<0.05) fecal $NH_3$ and $H_2S$ content compared with those fed NC diet. In conclusion, our results indicated that the inclusion of FC01 treatment could improve the growth performance, nutrient digestibility, fecal microbial shedding (lower E. coli and higher lactobacillus), and decrease the fecal noxious gas emission in growing pigs when compared with the group fed the basal diet. In conclusion, dietary FC could be considered as a good source of supplementation in growing pigs because of its growth promoting effect.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.5
• /
• pp.379-386
• /
• 1994

Reactions of 1',2-bis(diphenylphosphino)-l-(N,N-dimethylaminomethyl)ferrocene (FcNPP) with $M(CO)_6$ (M=Cr, Mo, W) in the presence of TMNO (Trimethylamine oxide) in a stoichiometric ratio of 1 : 1.5 : 3.5 produced a series of Gp 6 metal carbonyl derivatives with a variety of coordination modes: M(CO)$_4({\eta}^2$-FcNPP-P,P) (M=Cr, Mo, W), $M(CO)_5({\eta}^1-FcNPP-P) (M=Mo, W)\;,\; M_2(CO)_9({\eta}^1\;,\;{\eta}^2-FcNPP-P,P,N) (M=Cr, Mo)\;,\;M_2(CO)_{10}({\eta}^1\;,\;{\eta}^1-FcNPP-P,P) (M=Cr, Mo, W)\;, and\;W(CO)_4({\eta}^2-FcNPP(O)-P,N)$. All these complexes were characterized by microanalytical and spectroscopic techniques. In one case, the structure of W(CO)$_4({\eta}^2$-FcNPP(O)-P,N) was determined by X-ray crystallography. Crystals are monocinic, space group P$2_{1/C}$, with a=10.147(2), b=19.902(3), c=19.821(4) ${\AA},\;{\beta}=96.88(2)^{\circ},\;V=3974(l){\AA}^3$, Z=4, and $D_{calc}=1.64 g cm^{-3}$. The geometry around the central tungsten metal is a distorted octahedron, with the nitrogen and phosphorus atoms being cis to each other. Some of these complexes exhibited catalytic activities in the allylic oxidation and epoxidation of cholesterly acetate. Other oxidation products were also formed with the different chemical yields and product distribution depending upon the ligand and the central metal.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.28 no.1
• /
• pp.33-39
• /
• 2024

Understanding the behavior of soil under cyclic loading conditions is essential for assessing its response to seismic events and potential liquefaction. This study investigates the effect of non-plastic fines content (FC) on excess pore pressure generation in medium-density sand-silt mixtures subjected to strain-controlled cyclic direct simple shear (CDSS) tests. The investigation is conducted by analyzing excess pore pressure (EPP) ratios and the number of cycles to liquefaction (Ncyc-liq) under varying shear strain levels and FC values. The study uses Jumunjin sand and silica silt with FC values ranging from 0% to 40% and shear strain levels of 0.1%, 0.2%, 0.5%, and 1.0%. The findings indicate that the EPP ratio increases rapidly during loading cycles, with higher shear strain levels generating more EPP and requiring fewer cycles to reach liquefaction. At 1.0% and 0.5% shear strain levels, FC has a limited effect on Ncyc-liq. However, at a lower shear strain level of 0.2%, increasing FC from 0 to 10% reduces Ncyc-liq from 42 to 27, and as FC increases further, Ncyc-liq also increases. In summary, this study provides valuable insights into the behavior of soil under cyclic loading conditions. It highlights the significance of shear strain levels and FC values in excess pore pressure generation and liquefaction susceptibility.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.9
• /
• pp.725-733
• /
• 2002

In this study, the heat transport limitations of a two-phase closed thermosyphon were investigated. For the test, a two-phase closed thermosyphon ($L_t/: 600 mm,\;L_e:105mm,\;L_a:75mm,\;L_c:420mm,\;D_o:22.2mm,$ container: copper (inner grooved surface), working fluid: PFC ($C_6F_14$) was fabricated with a reservoir that can change the fill charge ratio. The following was imposed as the factors on the heat transport limitations of a two-phase closed thermosyphon. 1) Fill charge ratio of the working fluid. 2) Tilt angle of the longitudinal axis. From tile experimental data, some results were obtained as follows. When the fill charge ratio was relatively small ($\psi$20%), the heat transport limitation occurred about 100W by dry-out limitation. However over 40%, it shelved nearly constant value (500 W) by flooding limitation. The heat transport limitation according to the tilt angle increased smoothly until the tilt angle was $60^{\circ}$,/TEX>, after then decreased slowly.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.193-197
• /
• 2002

The tribological properties and van der Waals attractive forces and the thermal stability of films are very important characteristics of highly hydrophobic fluorocarbon (FC) films for the long-term reliability of nano system. The effect of thermal annealing on films and van der Waals attractive forces and friction coefficient of films have been investigate d in this study. It was coated Al wafer which was treated O2 and Ar that ocatfluorocyclobutane ($C_4_{8}$) and Ar were supplied to the CVD chamber in the ratio of 2:3 for deposition of FC Films. Static contact angle and dynamic contact angle were used to characterize FC films. Thickness of films was measured by variable angle spectroscopy ellipsometer (VASE). Nanotribological data was got by atomic force microscopy (AFM) to measure roughness, lateral force microscopy (LFM) to measure friction force, and force vs. distance (FD) curve to evaluate adhesion force. FC films were cured in N2 and vacuum. The film showed the slight changes in its properties after 3 hr annealing. FTIR ATR studies showed the decrease of C-F peak intensity in the spectra as the annealing time increased. A significant decrease of film thickness has been observed. The friction force of Al surface was at least thirty times higher than ones with FC films. The adhesive force of bare Al was greater than 100 nN. After deposit FC films adhesive force was decreased to 40 nN. The adhesive force of films was decreased down to 10 nN after 24 hr annealing. During 24 hr annealing in $N_2$and vacuum at $100^{\circ}C$ film properties were not changed so much.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1083-1087
• /
• 1999

Microstructures and the gas-sensing characteristics of the $\textrm{SnO}_2$ thin films were studied, which were deposited at various conditions (rf power, sample temperature, $\textrm{O}_2$/Ar ratio) by the rf magnetron sputtering. As a result, six typical microstructures were derived, such as amorphous(A), amorphous mixed with polycrystalline grains (A+P), polycrystalline with random crystalographic orientation (P), fine columnar (FC), coarse columnar (CC) and Zone T (T) with dense fiberous structure. Typically, A, A+ P, and P structures were formed when no $\textrm{O}_2$ was added to the sputter gas, whereas FC, CC, and T structures were obtained when $\textrm{O}_2$ was added. The A structure formed at low rf power and low temperature, the A+P at high rf power and low temperature, and the P at high rf power and high temperature. The FC structure was obtained at low rf power and low temperature. the CC at low rf power and high temperature, and the T at high rf power and low temperature. Results of the gas-sensing test of the sensor chips fabricated from the typical films indicated that the fine columnar microstructure shows the highest sensitivity both at $300^{\circ}C$ and $400^{\circ}C$. It was proposed that this is due to the high specific surface area of the micro-columns.

• Journal of Environmental Health Sciences
• /
• v.29 no.1
• /
• pp.19-27
• /
• 2003

Coliforms is currently being used as the standard of environmental water qualify to evaluate the level of source water quality especially condition of fecal contamination. However, not properly applied to water quality management. So in this study, in addition to Coliforms, fecal contamination indicator bacteria turk at Feral Coliforms(FC), E. coli, Fecal streptococci(FS), Clostridium and environmental parameters related with it's distribution were investigated on a monthly basis in 6 water intakes of Han River. The mean of BOD, DO, SS and pH, benchmarks of source water management were maintained the second grade of environmental water quality standard applied to Han River but Coliforms exceeded it. Distribution of Coliforms ranged from 1.0×10¹ to 2.7 10/sup 5/ CFU/ml, FC ranged from ND to 5.3×10¹ CFU/ml, E. coli ranged from ND to 9.2×10¹ CFU/ml, FS ranged from ND to 2.5×10¹CFU/ml, they were steepy rise on July and August in common when rainfalls was heavy and water temperature was high, but Clostridium perfringens ranged from 1.7×10¹to 1.7×10¹CFU/ml not fluctuate by month. Statistical analysis of sampling data showed that most significant correlations occurred among FC and Coliforms(r = 0.840), E. coli(r = 0.792), FS(r = 0.687) and environmental parameters(temperature, turbidity, SS, rotor were all r > 0.60) while no significant correlation was observed between ammonia generally recognized fecal contamination indicator and bacteria. Identification of the coliforms showed that Enterobacter, Klebsiella, Citrobacter were comprised of 32%, 24%, 16% respectively, and E. coli were 7% of it. while E. coli was made up 85.9% of FC. The mean value of FC/Coliforms ratio, 5.2(0.1-42) were higher in Amsa, Guui than Jayang. Fecal coliforms, as those are able to reflect more particularly the extent of the fecal contamination, were considered useful in deciding the level of water treatment while monitoring the fecal contamination from the source of water supply. Therefore, it is expected that the water quality is going to be managed more efficiently by using fecal coliforms supplementarily to total coliforms which are current standard item of water-quality environment.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.5
• /
• pp.650-657
• /
• 2002

Two experiments were conducted to evaluate the effects of forage:concentrate ratios and feeding principles on milk yield, milk composition, body weight change, postpartum oestrus and feed cost. A total of 36 crossbred F1 cows (Holstein Friesian${\times}$Local Yellow) in the 8th week of lactation were used. In each experiment, animals were divided into three groups using a randomized block design according to the milk yield of the previous eight weeks. Cows were fed 30, 50 and 70% concentrate in the diet based on DM. In experiment 1 (Fc), cows were given the same amount of DM with constant ratios of forage and concentrate within treatments. In experiment 2 (Fa), cows were given the same constant amounts of concentrate as in experiment 1 and ad libitum forage. The forage consisted of a natural grass mixture based on 5 species of grasses with high nutritive values. There was no difference in total DM intake between treatments within experiments. However, cows fed forage ad libitum had higher DM intakes compared to cows fed constant forage (1.6, 4.5 and 9.5% for cows fed 70, 50 and 30% forage, respectively). Daily milk yield of cows fed forage ad libitum was higher than that of cows fed constant forage:concentrate ratio. Within experiment, milk yield was highest for cows fed 30% DM forage, followed by cows fed 50% and then cows fed 70% forage (11.17, 10.98 and 10.71 for the 30Fc, 50Fc and 70Fc cows; 11.73, 11.16 and 10.81 kg for the 30Fa, 50Fa and 70Fa cows, respectively). Decreased forage ratio in the diets resulted in decreased milk fat content and tended to increase milk protein. Increased concentrate ratio in the diet and feeding forage ad libitum increased body weight gain. The effect of forage:concentrate ratio on postpartum oestrus was not significant. The feed cost per kg milk produced was lowest for the cows fed 70% forage. It is concluded that increased ratio of concentrate resulted in increased body weight gain, milk yield, milk protein, and decreased milk fat. Feeding forage ad libitum increased feed intake, milk yield and body weight gain. The ratio of 50% forage is more suitable for milk production and animal condition, but in terms of feed cost and under the conditions of small dairy farmers, the 70% ad libitum forage feeding is recommended.