• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 추계종합학술대회
• /
• pp.1000-1002
• /
• 2005

최대 7기기까지의 슬레이브 디바이스들과 연결이 가능한 블루투스 피코넷에서, RF 연결단으로 송신되는 무선 데이터는 블루투스 버전 1.1 송신 규약에 적합하도록 1마이크로미터 단위로 슬라이싱되어 베이스밴드 입력단으로 들어오게 된다. 본 연구에서는 상대적으로 불안정한 RF 디바이스에서 베이스밴드로 전달되는 아날로그 신호를 1 마이크로미터 단위의 정확한 슬라이싱을 가능하게 해 주고, 또한 불안정한 아날로그에 대한 신호의 노이즈를 제거할 수 있는 디지털 로우패스 필터를 설계하였다. 설계된 디지털 로우패스필터는 블루투스 RF 일체형 베이스밴드 침의 절전 모드, 정상동작 모드와 고속 동작 모드인 12MHz, 24MHz, 48MHz 각 주파수에서 모두 정상적으로 동작하였다.

• Current Optics and Photonics
• /
• 제7권5호
• /
• pp.485-495
• /
• 2023

The pixel size in high-resolution complementary metal-oxide-semiconductor (CMOS) image sensors continues to shrink due to chip size limitations. However, the pixel pitch's miniaturization causes deterioration of optical performance. As one solution, a quad color filter (CF) array with pixel binning has been developed to enhance sensitivity. For high sensitivity, the microlens structure also needs to be optimized as the CF arrays change. In this paper, the covered microlens, which consist of four microlenses covered by one large microlens, are proposed for the quad CF array in the backside illumination pixel structure. To evaluate the optical performance, the suggested microlens structure was simulated from 0.5 ㎛ to 1.0 ㎛ pixels at the center and edge of the sensors. Moreover, all pixel structures were compared with and without in-pixel deep trench isolation (DTI), which works to distribute incident light uniformly into each photodiode. The suggested structure was evaluated with an optical simulation using the finite-difference time-domain method for numerical analysis of the optical characteristics. Compared to the conventional microlens, the suggested microlens show 29.1% and 33.9% maximum enhancement of sensitivity at the center and edge of the sensor, respectively. Therefore, the covered microlens demonstrated the highly sensitive image sensor with a quad CF array.

• Journal of Preventive Medicine and Public Health
• /
• 제7권1호
• /
• pp.101-105
• /
• 1974

A study was carried out for the purpose of grasping the status of bacteriological contamination of the public wells in Iri city, during the period from 1 to 15 August, 1974. Coliform groups were detected by membrane filter method and physical conditions of the wells were checked. As results of this study, following conclusion were obtained. 1. The households which used the piped water occupied 70.8 per cent (11,907 households) out of total householdsir Iri city. 2. Temperature of the well water was 38 out of 50 samples (72.0%) with 12.1 to $16.0^{\circ}C$ and 9 wells with 10.1 to $12.0^{\circ}C$. 3. The pH values range of the well water was 6.0 to 7.9, 11 cases or 22,0 per cent less than 6.5 and 8 cases or 16.0 per cent more than 7.5. 4. The residual chlorine was found at 15 samples (30.0%) contained 0.1 to 0.5ppm, 9 samples (18.0%), 0.6 to 1.0 ppm after 24 houres of chlorination. 5. Coliform groups were found at 49 out of 50 samples (98.0%) before chlorination when 100ml well waters was tested by membrane filter technique and 15 wells(30.0%) were potable for drinking within 24 houres after chlorination. 6. Coliform groups positves were 23 out of 26 samples (88.5%) with no residual chlorine, 12 out of 16 samples (80.0%) with 0.1 to 0.5ppm and none out of 9 with 0.6 to 1.0ppm.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2007년도 추계학술발표대회
• /
• pp.748-749
• /
• 2007

본 논문은 저전력이고 속도가 빠르면서도 작은 gate 면적만으로 JPEG2000 표준의 이산 웨이블릿 변환 (DWT)을 수행하는 VLSI 구조를 제안하였다. 제안한 구조는 line-based 와 convolution 방식을 사용하여 설계하였다. DWT 필터는 1 차원 구조로서 영상의 수평방향이나 수직방향을 차례대로 처리하였고, 16-비트 고정 소수점 형식의 Daubechies 9/7 필터 계수를 사용하였다. 기존의 DWT VLSI 설계에서 매우 큰 영역을 차지하는 multiplier 들을 shift-adder 들로 대체하여 기존 방식의 gate 사용 면적을 38.5% 로 크게 줄일 수 있었다. 또한 최대 지연시간과 총 소비전력은 각각 기존에 비해 78% 와 29.6% 로 개선되었다.

• 한국환경보건학회지
• /
• 제22권2호
• /
• pp.32-42
• /
• 1996

This study was performed to evaluate accuracy and precision of filter method and impinger method for analyzin airborne isocyanates in mixture (2, 6-TDI, HDI, 2, 4-TDI, MDI). Filter method was performed using the OSHA Method 42 and impinger method using the NIOSH Method 5521. The samples were analyzed by high performance liquid chromatography-ultraviolet detector (HPLC-UVD). After the optimum operating conditions for each method were investigated, samples with various concentration levels were quantified at the conditions. The precision was expressed by the pooled coefficient of variation(C.V.) and the accuracy by overall accuracy. The results are summarized as follows: 1. The optimum condition of filter method was determined at 35/65 ACN/buffer (0.01 M ammonium acetate) in mobile phase. And in case of impinger method, it was at 30/70 ACN/buffer(0.2 M sodium acetate). The effect of concentrations of acetate on the separation of the peaks was not significant, but, the effect of ACN/buffer ratio was significant. 2. The correlation coefficients for the two methods were above 0.9 in all isocyanate compounds. Average recovery efficiencies for 2, 6-TDI, HDI, 2, 4-TDI and MDI in filter method were 92.4%, 102.6%, 87.3% and 101.0%, respectively. Those in impinger method were 106.6%, 106.7%, 99.0% and 103.6%, respectively. As a result, the recovery efficiency of impinger method was higher than those of filter method in analyzing isocyanate compounds. 3. The pooled coefficients of variations of the methods were slightly higher than expected. The overall accuracies of the methods were within $\pm 25%$ for each isocyanate compound. Since these results satisfy NIOSH criteria, the accuracy of the experiment is appropriate. 4. As seen above, impinger method is more efficient than filter method. But, there are many disadvantages in impinger method. Therefore, solid sorbent such as a glass fiber filter must be developed in order to have the high efficiency not less than that of impinger method in the future.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.78-81
• /
• 2000

A new type low-pass filter design method based on a coupled line and transmission line theory is proposed to suppress harmonics by attenuation poles in the stop band The design formula are derived using the equivalent circuit of a coupled transmission line. The new low-pass filter structure is shown to have attractive properties such as compact size, wide stop band range and low insertion loss. The seventh-order low-pass filter designed by present method Ins a cutoff frequency of 0.9 GHz with a 0.01 dB ripple level. The coupled line type low-pass filter with stripline configuration was fabricated by using a high-temperature superconducting (HTS ; $YBa_2Cu_3O_{7-x}$) thin film on MgO(100) substrate. Since the HTS coupled line type low-pass filter was proposed with five attenuation poles in stop band such as 1.8, 2.5, 4, 5.5, 62 GHz. The fabricated low-pass filter has improved the attenuation characteristics up to seven times of the cutoff frequency Bemuse of good rejection of the spurious signals and harmonics, our low-pass filter is applicable to mobile base station systems such as cellular, personal communication systems and international mobile telecommunication(IMT)-2000 systems.

• 한국멀티미디어학회논문지
• /
• 제13권7호
• /
• pp.943-949
• /
• 2010

본 논문은 하드웨어 곱셈 연산을 최적화하여 리프팅 기반의 9/7 웨이블릿 필터의 개선된 VLSI의 구조를 제안한다. 제안한 구조는 범용 곱셈기를 사용하는 기존의 리프팅 기반의 웨이블릿 필터와 비교하여 화질의 열화 없이 보다 적은 로직과 전력소모를 갖는다. 본 논문은 Pattern search 기반의 Lefevre 알고리즘을 이용하여 하드웨어 구조를 개선한다. 제안한 구조는 범용의 곱셈기를 단순한 shift-add 연산으로 대체하여 하드웨어 구현을 단순하게 하고 계산 속도를 빠르게 한다. 제안한 구조와 기존의 구조를 Verilog HDL을 이용하여 구현하고 비교 실험하였다. 두 구조는 0.18um 디지털 CMOS 공정의 스탠다드 셀을 이용하여 합성된다. 제안한 구조는 200MHz의 합성 타겟 클록 주파수에서 기존의 구조에 비해 면적, 전력소모와 최대 지연시간이 각각 약 51%, 43%와 30%로 감소하였다. 구현 결과를 통해 제안한 구조가 범용의 곱셈기 블록을 사용한 기존의 구조보다 스탠다드 셀을 이용한 ASIC 구현에 보다 적합하다는 것을 보여준다.

• 한국농공학회논문집
• /
• 제49권2호
• /
• pp.75-86
• /
• 2007

This process which has a connection of biofilter and sulfur-limestone has been developed to treat organic substances including BOD, COD and SS etc. and to treat sulfur-limestone is for denitrification.. The whole process consists of chemical reaction tank, sedimentation tank, trickling filter, denitrification tank The trickling filter is equipped with a reactor filled with absorptive filter, and the sulfur denitrification tank is filled with sulfur-limestone mixed media. After setting up practical facilities whose capacity is 60 tons a day, we have observed the removal efficiencies of pollutants through 60 experiments during Summer and Winter seasons. The average concentration of polluted water was BOD for 3.6 mg/L, $COD_{Mn}$ for 11.3 mg/L, SS for 2.8 mg/L, T-N for 8.6 mg/L, and T-P for 0.8 mg/L, and the rate of treatment efficiencies 96.5%, 84.7%, 96.5%, 79.2%, and 80.8%, respectively was found through the experiments. The average treatment efficiency for BOD and $COD_{Mn}$ was 85.0% and 55.7%, respectively and the average removal efficiency for NH4+-N was 84.9% in the trickling filter. The removal efficiency in the denitrification tank is as follows; The removal rate of $NO_3^--N$ was as high as 93.2% within the compass of pH 6.3 to 7.3 through $16.8{\sim}37.0mg/L$ flown into $NO_3^--N$ and $0.1{\sim}8.3mg/L$ outflown. It had observed that this process has implemented highly efficient and advanced treatment without external carbon sources and internal recycle during its process. In conclusion, this process is suitable for a sewerage in a small village due to the merits of low power consumption and easy maintenance.

• 환경위생공학
• /
• 제22권4호
• /
• pp.119-130
• /
• 2007

Sea food wastewater including high concentration of organics and nutrients is hard to treat stably by established traditional activated sludge process. This research is aimed to obey more and more of strengthened the law and to secure stable effluents by using advanced treatment process applied membrane filter in aeration tank for treatment of wastewater from marine products. It must maintain pH of influent over 6.0 to keep up stably biological sludge of advanced treatment process. At 38hr of HRT, removal rates of TBOD and TCOD were 99.9% and 99.4% respectively and TSS also removed with high efficiency. Most organics in the effluent was constituted with soluble type materials, it caused that membrane filter installed aeration tank should remove minute suspended particles. The reactor was operated well to get stable treatment results for operation period, in spite of high loading of organics like that $0.67{\sim}1.67\;kgTBOD/m^3/day$ of organics loading and $0.10{\sim}0.21\;kgBOD_5/kgMLSS/day$ of F/M ratio. At $36{\sim}48hr$ of HRT, removal rates of T-N and T-P were $89.7{\sim}90.7%\;and\;91.5{\sim}96.0%$ respectively. It means this treatment process also work to remove nutrients of high concentration. Upon investigation of advanced treatment's operation factors, optimum SRT was about 30days and average SNR that showed tendency to increase according to increase water temperature was calculated 0.014 gN/g MLVSS/d. SDNR was risen in conformity to increase F/M ratio of Non-aeration tank and investigated as $0.038{\sim}0.051\;gN/gMLVSS/d$.