• Journal of electromagnetic engineering and science
• /
• v.19 no.1
• /
• pp.20-30
• /
• 2019

A wide-band multiple-input multiple-output (MIMO) antenna with dual-band (2.4 and 5 GHz) operation is proposed for premium indoor access points (IAPs). Typically, an omni-directional pattern is used for dipole antennas and a directional radiation pattern is used for patch antennas. In this paper, both antenna types were used to compare their performance with that of the proposed $2{\times}2$ MIMO antenna. We simulated and measured the performance of the MIMO antenna, including the isolation, envelope correlation coefficient (ECC), mean effective gain (MEG) for the IAPs, and the throughput, in order to determine its communication quality. The performance of the antennas was analyzed according to the ECC and MEG. The proposed antenna has sufficient performance and excellent characteristics, making it suitable for IAPs. We analyzed the communication performance of wireless networks using the throughput data of a typical office environment. The network throughput of an 802.11n device was used for the comparison and was conducted according to the antenna type. The results showed that the values of the ECC, MEG, and the throughput have unique characteristics in terms of their directivity, antenna gains, isolation, etc. This paper also discusses the communication performance of various aspects of MIMO in multipath situations.

• Journal of KIISE
• /
• v.41 no.10
• /
• pp.810-823
• /
• 2014

The wireless mesh network based on IEEE 802.11s provides a routing based on a destination address as it inherits legacy internet architecture. However, this architecture interested in not 'what' which is originally the users goal but 'where'. Futhermore, because of the rapid increase of the number of mobile devices recently, the mobile traffic increases geometrically. It reduces the network effectiveness as increasing many packets which have same payload in the situation of many users access to the same contents. In this paper, we propose an OpenFlow-based contents routing for the wireless mesh network(WMN) to solve this problem. We implement contents layer to the legacy network layer which mesh network uses and the routing technique based on contents identifier for efficient contents routing. In addition we provide flexibility as we use OpenFlow. By using this, we implement caching technique to improve effectiveness of network as decreasing the packet which has same payload in WSN. We measure the network usage to compare the flooding technique, we measure the delay to compare environment using caching and non caching. As a result of delay measure it shows 20% of performance improve, and controller message decrease maximum 89%.

• Journal of Advanced Navigation Technology
• /
• v.14 no.3
• /
• pp.328-335
• /
• 2010

In this paper, an efficient algorithm and area-efficient hardware architecture have been proposed for $2{\times}2$ MIMO-OFDM based WLAN baseband modem with two transmit and two receive antennas. To enhance the performance of the receiver, the efficient timing synchronization algorithm and symbol detector based on MML algorithm are presented. Also, by sharing the hardware block with multi-stage pipeline structure and using the complex multiplier based on polar-coordinate, the complexity of the proposed architecture is dramatically decreased. The proposed area-efficient hardware design was designed in hardware description language (HDL) and synthesized to gate-level circuits using 0.13um CMOS standard cell library. As a result, the complexity of the proposed modem receiver is reduced by 56% over the conventional architecture.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.7
• /
• pp.775-782
• /
• 2016

In this paper, we presented the paper-based reconfigurable frequency selective surface(FSS) for transmitting or blocking the wireless LAN signal in indoor environments. The proposed reconfigurable FSS are designed on coated paper using a printing of conductive ink and conductive adhesive for PIN diode, which provides ON/OFF of the reconfigurable FSS for passing or blocking the 5GHz signal. The reconfigurable FSS attached on the wall can pass or block the incident wireless signal as the received signal strength in indoor. To provide the validity of the proposed FSS, we fabricated the reconfigurable FSS on the paper and confirmed the very similar results between simulations and measurements. From the measured results of the proposed spectrum control system, we know that the proposed reconfigurable FSS can block about 20dB at 5.745GHz~5.805GHz.

• Nuclear Engineering and Technology
• /
• v.47 no.6
• /
• pp.729-737
• /
• 2015

Wireless communication technologies, especially smartphones, have become increasingly common. Wireless technology is widely used in general industry and this trend is also expected to grow with the development of wireless technology. However, wireless technology is not currently applied in any domestic operating nuclear power plants (NPPs) because of the highest priority of the safety policy. Wireless technology is required in operating NPPs, however, in order to improve the emergency responses and work efficiency of the operators and maintenance personnel during its operation. The wired telephone network in domestic NPPs can be simply connected to a wireless local area network to use wireless devices. This design change can improve the ability of the operators and personnel to respond to an emergency situation by using important equipment for a safe shutdown. IEEE 802.11 smartphones (Wi-Fi standard), Internet Protocol (IP) phones, personal digital assistant (PDA) for field work, notebooks used with web cameras, and remote site monitoring tablet PCs for on-site testing may be considered as wireless devices that can be used in domestic operating NPPs. Despite its advantages, wireless technology has only been used during the overhaul period in Korean NPPs due to the electromagnetic influence of sensitive equipment and cyber security problems. This paper presents the electromagnetic verification results from major sensitive equipment after using wireless devices in domestic operating NPPs. It also provides a solution for electromagnetic interference/radio frequency interference (EMI/RFI) from portable and fixed wireless devices with a Wi-Fi communication environment within domestic NPPs.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.476-483
• /
• 2016

Super Wi-Fi is a Wi-Fi-like service exploiting TV white space (WS) which is expected to achieve larger coverage than today's Wi-Fi thanks to its superior propagation characteristics. Super Wi-Fi has been materialized as an international standard, IEEE 802.11af, targeting indoor and outdoor applications, and is undergoing worldwide field tests. This paper demonstrates the true potential of indoor Super Wi-Fi, by experimentally comparing the signal propagation characteristics of Super Wi-Fi and Wi-Fi in the same indoor environment. Specifically, we measured the wall and floor attenuation factors and the path-loss distribution at 770MHz, 2.401 GHz, and 5.540 GHz, and predicted the downlink capacity of Wi-Fi and Super Wi-Fi. The experimental results have revealed that TVWS signals can penetrate up to two floors above and below, whereas Wi-Fi signals experience significant path loss even through a single floor. It has been also shown that Super Wi-Fi mitigates shaded regions of Wi-Fi by providing almost-homogeneous data rates within its coverage, performs comparable to Wi-Fi utilizing less bandwidth, and always achieves better spectral efficiency than Wi-Fi. The observed phenomena imply that Super Wi-Fi is suitable for indoor applications and has the potential of extending horizontal and vertical coverage of today's Wi-Fi.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.726-732
• /
• 2019

In this study, we proposed an asymmetric differential inductor to improve the linearity of differential power amplifiers. Considering the phase error between differential signals of the differential amplifier, the location of the center tap of the differential inductor was modified to minimize the error. As a result, the center tap was positioned asymmetrically inside the differential inductor. With the asymmetric differential inductor, the AM-to-AM and AM-to-PM distortions of the amplifier were suppressed. To confirm the feasibility of the inductor, we designed a 2.4 GHz differential CMOS PA for IEEE 802.11n WLAN applications with a 64-quadrature amplitude modulation (QAM), 9.6 dB peak-to-average power ratio (PAPR), and a bandwidth of 20 MHz. The designed power amplifier was fabricated using the 180-nm RF CMOS process. The measured maximum linear output power was 17 dBm, whereas EVM was 5%.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2008.05a
• /
• pp.995-998
• /
• 2008

무선 통신 기술의 발전과 함께 802.11n과 같은 광대역 네트워크 인프라의 구축이 확대됨에 따라, 이에 적합한 높은 성능을 낼 수 있는 전송 계층의 프로토콜이 필요하다. 유선 환경에서 개발된 TCP(Transmission Control Protocol)는 현재 가장 널리 이용하는 전송 프로토콜이다. 하지만 높은 에러율과 긴 딜레이가 발생하는 무선 네트워크상에서는 패킷 손실의 원인을 구별하지 못하기 때문에 성능이 저하된다. 또한, 광대역폭을 지원하는 초고속 네트워크상에서 TCP가 동작할 경우 기존 무선 네트워크에서 처리하는 혼잡윈도우 값보다 커진 값을 제대로 처리하지 못하기 때문에 가용대역폭을 활용하지 못하는 문제점이 발생한다. 따라서, 본 논문에서는 초고속 네트워크 안에서 slowstart threshold에 기반하여 가용대역폭을 동적으로 획득하고, 높은 전송률을 보장하는 TCP VEST(TCP Vegas-based Estimator with Slowstart Threshold)를 제안한다. TCP VEST는 기본적으로 송신자기반 무선네트워크에서 우수한 성능을 지원하는 TCP WestwoodVT의 패킷 손실원인 구분법을 사용한다. 그리고 TCP VEST는 패킷 손실의 원인을 구분하고 각각의 경우에 따라서 전송량을 slowstart threshold 값의 변화에 맞춰 조절한다. NS-2를 통한 성능평가에서 VEST는 WestwoodVT와 비교했을 때 링크 에러율이 1%인 환경에서는 20% 이상의 전송률 향상을 나타내며, Westwood와 비교했을 때는 60%의 성능향상이 있다. 또한 초고속 네트워크에서 5%와 10% 사이의 에러율을 가질 때에는 WestwoodVT와는 50%, Westwood와는 300% 이상의 성능향상이 나타남을 보인다. 이를 통해 VEST가 기존의 무선 네트워크와 더불어 초고속 네트워크에서도 동적으로 대역폭을 획득함으로써 높은 전송률을 지원하는 것을 입증한다.

• Analytical Science and Technology
• /
• v.22 no.4
• /
• pp.336-344
• /
• 2009

This survey was carried out to estimate the contents of heavy metals (Hg, Pb, Cd, and As) in 10 kinds of dried marine products (n=189) which are closely related to food resources. The contents of heavy metals were estimated by inductively coupled plasma spectrometer (ICP) and mercury analyzer. The values of heavy metals in dried marine products were as follows (Mean${\pm}$SD (range), mg/kg). The average contents of heavy metals in the dried marine products were Hg $0.058{\pm}0.069$ (0.002~0.502) mg/kg, Pb $0.178{\pm}0.598$ (ND~5.130) mg/kg, Cd $0.306{\pm}0.610$ (ND~6.802) mg/kg, As $5.282{\pm}6.158$ (ND~71.760) mg/kg. The range of heavy metal contents in dried marine products are low level, except of lead contents (n=2). In the comparison of heavy metal content by anchovy size, it was shown that cadmium, mercury and arsenic were meaningfully different. The contents of heavy metals by the shape of shrimp and Alaska Pollack were shown that the result of each group was meaningless. In the comparison imported production with domestic production, in the case of common squid, cadmium and arsenic were meaningfully different. The weekly average intakes of Hg, Pb and Cd from dried marine products takes about 1.17~11.52% of PTWI (Provisional Tolerable Weekly Intakes) that FAO/WHO Joint Food Additive and Contaminants Committee has set to evaluate their safeties.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.11
• /
• pp.795-802
• /
• 2013

According to the increase of impervious area due to the town development, the rate of infiltration generally lessens and that of runoff rises during wet weather events. And it is concerned that its impacts on water quality for the downstream water bodies due to the change of rainfall runoff patterns may also increase. To cope with these issues, LID (Low Impact Development) techniques which try to maintain the characteristics of rainfall runoff regardless of the town development have been introduced actively. However, the behaviors of each LID technique for rainfall runoff and pollutant loads is not understood sufficiently. In this study, considering the applications of some LID techniques, several sets of simulations using a distributed rainfall runoff model, SWMM-LID, have been conducted for D town whose development is progressing. As the results of the simulations, the rates of infiltration/storage have been decreased from 78% in the case before the town development to 15% after the development and increased again by 24% with LID techniques such as porous pavement, rain barrel and rain garden. The rates of runoff have been increased more than three times from 20% in the case before the development to 74% after the development, and they have also been decreased to 66% by the adoption of LID techniques. It has been simulated that porous pavement is more effective than others in the view point of the reduction of runoff and rain barrel is more attractive for the management of pollutant loads (TSS, BOD, COD, T-N and T-P). Therefore, if some LID techniques should be selected for the a new town, it could be concluded that some techniques with better infiltration functions are recommendable for the control of runoff, and ones with larger storage functions for the management of pollutant loads.