• Korean Journal of Agricultural Science
• /
• v.15 no.2
• /
• pp.143-152
• /
• 1988

This study was conducted to obtain basic data which affected engine performance of the power tiller being widely used in the rural area. Among the various factors affected engine performance, only flywheel weight was considered as the major factor in this study. Fuel consumption ratio, motoring loss, torque, vibration and mechanical efficiency of the engine tested were measured and analyzed on the four levels of flywheel weight (32.2, 29.7, 26.4, 24.2 kg). The results obtained were as follows: 1. The maximum output of 6 and 7.5 kW engine was 7.43 kW and 7.85 kW respectively. When flywheel weight was reduced from 32.2 kg to 24.2 kg, output power of the engine was increased 0.27 kW in 6 kW engine and increased 0.39 kW in 7.5 kW engine. 2. The fuel consumption ratio was decreased from 300.8 to 296.8 g/kW-hr in 6 kW engine and decreased from 313.6 to 312.8 g/kW-hr in 7.5 kW engine when the flywheel weight was reduced from 32.2 kg to 24.2 kg. 3. The mechanical efficiencies of the engine was increased from 76.1 to 76.8% in 6 kW engine and increased from 76.7 to 77.0% in 7.5 kW engine when the flywheel weight was reduced from 32.2 kg to 24.2 kg. 4. When the flywheel weight was reduced from 32.2 kg to 24.2 kg, a tendency of a little decrease of vibration at X- and Z-axis in 6 kW engine and of a little increase of vibration at Y-axis in 6 kW engine and all directions in 7.5 kW engine was observed. 5. Motoring losses was decreased from 2.33 to l.76 kW in 6 kW engine and decreased from 2.46 to 1.84 kW in 7.5 kW engine when the flywheel weight was reduced from 32.2 kg to 24.2 kg. From the above results and the flywheel weight calculated theoretically, it was recommendable that the flywheel weight should be reduced about 7 kg in 6 kW engine and about 10 kg in 7.5 kW engine, respectively.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.5
• /
• pp.493-498
• /
• 2019

This study deals with the analysis of the technology association rules between CPC codes of the Internet of Things(IoT) patent, the core of the Fourth Industrial Revolution ICT-based technology. The association rules between CPC codes were extracted using R, an open source for data mining. To this end, we analyzed 369 of the 605 patents related to the Internet of Things filed with the Patent Office until July 2019, with a complex CPC code, up to the subclass-level. As a result of the technology association rules, CPC codes with high support were [H04W ${\rightarrow}$ H04L](18.2%), [H04L ${\rightarrow}$ H04W](18.2%), [G06Q ${\rightarrow}$ H04L](17.3%), [H04L ${\rightarrow}$ G06Q](17.3%), [H04W ${\rightarrow}$ G06Q](9.8%), [G06Q ${\rightarrow}$ H04W](9.8%), [G06F ${\rightarrow}$ H04L](7.9%), [H04L ${\rightarrow}$ G06F](7.9%), [G06F ${\rightarrow}$ G06Q](6.2%), [G06Q ${\rightarrow}$ G06F](6.2%). After analyzing the technology interconnection network, the core CPC codes related to technology association rules are G06Q and H04L. The results of this study can be used to predict future patent trends.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.2
• /
• pp.213-217
• /
• 1997

Magnesium reduction of Mo(N-C6H3-2,6-i-Pr2)2Cl2(DME) in the presence of trimethylphosphine led to a mixture of Mo(N-C6H3-2,6-i-Pr2)(PMe3)2Cl3, 1, and Mo2(PMe3)4Cl4, 2. In solution 1 is slowly air-oxidized to Mo(N-2,6-i-Pr2-C6H3)(OPMe3)(PMe3)Cl3, 3. 1 is chemically inert to carbon nucleophiles (ZnMe2, ZnEt2, AlMe3, AlEt3, LiCp, NaCp, TlCp, NaCp*, MeMgBr, EtMgBr), oxygen nucleophiles (LiOEt, LiO-i-Pr, LiOPh, LiOSPh), and hydrides (LiBEt3H, LiBEt3D). Crystal data for 1: orthorhombic space group P212121, a=11.312(3) Å, b=11.908(3) Å, c=19.381(6) Å, Z=4, R(wR2)=0.0463 (0.1067). Crystal data for 2: monoclinic space group Cc, a=18.384(3) Å, b=9.181(2) Å, c=19.118(3) Å, b=124.98(1)°, Z=4, R(wR2)=0.0228 (0.0568). Crystal data for 3: orthorhombic space group P212121, a=11.464(1) Å, b=14.081(2) Å, c=16.614(3) Å, Z=4, R(wR2)=0.0394 (0.0923).

• Korean Journal of Human Ecology
• /
• v.3 no.2
• /
• pp.77-89
• /
• 2000

In this study, to activate the industrialization and to improve the quality of Toha-jeot by shortening the fermentation period, we investigated the changes in the nutritional components of Toha-jeot. salt-fermented Toha shrimp( Caridina denticulata denticulata $D_{E}$ $H_{AAN}$) which was salted with a low-salt group and high-salt group during fermentation. In this experiment. there are four groups of Toha-jeot which were manufactured with 15% ratio of common salt: the first group containing 2% wheat bran (w2%-L). the second high-salt group containing 2% wheat bran( w2%-H) , the third low-salt group containing 4% wheat bran (w4%-L) and the last high-salt group containing 4% wheat bran(w4%-H). These four groups were refrigerated at 4${\pm}$1$^{\circ}C$ and then taken out for analysis at three month intervals during 9 month. Among the free amino acid contents in Toha-jeot, 22 kinds were detected. 6 month after the fermentation when the quantity of the amino acid contents in Toha-jeot is highest, ornitine, glutamic acid, leucine. alanine. lysine and valine occupy the majority, in the order of abundance. In cases of nucleotides. 6 month after the fermentation. from the groups w2%-L, w2%-H and w4%-L, inosine and IMP were not detected. and hypoxanthine, AMP, ADP were detected but 9 month after the fermentation ADP was not detected. The main constituents of fatty acid were as follows : (a) from w2%-L, w2%-H, 6 month after the fermentation. $C16:0$, $C12:0$, $C18:1$, $C18:3$, and $C16:1$. (b) from w4%-L. 6 month after the fermentation, $C18:3$, $C16:0$, $C12:0$ and $C18:1$. (c) from W4%-H, $C16:0$, $C12:0$, $C18:3$ and $C18:1$. In case of mineral contents. Na, Ca. K. Mg, Fe. Zn, Mn and Cu were detected according to the magnitude of the quantity. From the group w4%-H, high quantity of Na was detected during the total fermentation period. In case of color value, from the groups w2%. the values of L. a. b were highest after 6 month fermentation and were decreased after 9 month fermentation, while from groups w4%, the values of L, a, b were gradually decreased after 3 month fermentation.ion.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.4 no.1
• /
• pp.128-137
• /
• 2002

This study was conducted to develop the heat exchanger by utilizing the heat energy of underground water(15℃), which might be used for cooling and heating system of the agricultural facilities. We developed the heat exchanger by using the parallel type plat fin tube made of Aluminum(Al 6063), which was named Aloo-Heat(No. 0247164, offered by Korean Intellectual property Office). The trial manufactures were made from Aloo-heat which was 600mm, 700mm length respectively, and It were welded to the end "U" type in order to direct flow of the underground water. The performance test was carried out under the condition of open space and room temperature with the change of flow rate of the underground water and air. The results are as follows. 1. The trial manufactures had convection heat value from 33 to 156 W/m²℃, and It was coincided with design assumption. 2. The amount of energy transfer was increased with the increment of the area of heat transfer, the air flow, the gap of temperature inlet & outlet the underground water and the air. 3. The heat value was 6,825W when the air flow was 6,000m³/h and the gap of temperature between inlet and outlet of the underground water was 6℃, and It dropped from 25.8℃ to 23.2℃(-2.6℃ difference). The convection heat value was 88.5W/m²℃. 4. The heat value was 2.625W when the air flow was 4,000m³/h and the gap of temperature between inlet and outlet the underground water was 2℃, and It dropped from 27℃ to 22.5℃(-4.5℃ difference). The convection heat value was 33.6W/m²℃. 5. Correlation values(R²) of the testing heat values of the trial manufacture type I, II, and III were 0.9141, 0.8935, and 0.9323 respectively, and correlation values(R²) of the amount of the air flow 6,000m³/h, 5,000m³/h, 4,000m³/h were 0.9513, 0.9414, and 0.9003 respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.1021-1026
• /
• 2000

The removal of cadmium, copper and chromium ions was carried in a phase transfer reactor using W/O(water in oil) microemulsion containing sodium di[2-ethylhexyl] sulfosuccinate(AOT) and isooctane system. Removal efficiencies and mass transfer rate of $Cd^{2+}$, $Cu^{2+}$ and $Cr^{3+}$ were increasing with increasing pH of aqueous solution. However, $Cr^{6+}$ was not extracted by W/O microemulsion with AOT/isooctane system. It was found that removal of heavy metal ions were required an attractive electrostatic interaction between the metal ions and W/O microemulsion. The relationship between mass transfer rate. Jo of $Cd^{2+}$, $Cu^{2+}$ and $Cr^{3+}$ and pH of aqueous solution by W/O microemulsion suggested.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.6
• /
• pp.638-640
• /
• 2000

• Solar Energy
• /
• v.10 no.2
• /
• pp.38-43
• /
• 1990

The present study was to investigate the use of a phase change material for hydronic radiant floor heating. Two identical unit test cells sized $1.8m^L{\times}1.8m^W{\times}1.8m^H$ were built and installed with specially designed $1.6cm^T{\times}9cm^W{\times}80cm^H$ aluminum Ondol-panels holding 1.25kg of calcium chloride hexahydrate(CCH) each. It was found that the Ondol-panel with CCH reduced the room temperature fluctuations and maintains the phase changing temperature for considerably long duration, $2{\sim}4$ times of heating hour, over no-CCH one.

• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.106-111
• /
• 2021

In this study, an ultrasound-assisted micellar extraction process was developed to efficiently purify the anticancer substance paclitaxel from the plant cell Taxus chinensis. The problem of many extraction steps and long phase separation time in the traditional micellar process could be dramatically improved. The highest paclitaxel yield (~96%, extracted twice) was obtained at 180 W of ultrasonic power and 1.5 h of ultrasonic irradiation time, which was 24.7% higher than that of the traditional method. In addition, the partition coefficient (K) showed a maximum value (24.0) at 180 W of ultrasonic power and 1.5 h of irradiation time. There was no significant difference in the purity of paclitaxel, and the purity of initial paclitaxel (6.81%) increased to 22.0% after purification. Compared to the traditional method, the phase separation time of the back extraction decreased by 40.7-56.2% (ultrasonic power 80 W), 46.3-67.6% (ultrasonic power 180 W), and 51.9-67.6% (ultrasonic power 250 W), respectively. The phase separation time decreased as the ultrasonic power (80-250 W) and irradiation time (0.5-2.5 h) increased.

• Transactions of Materials Processing
• /
• v.27 no.1
• /
• pp.48-53
• /
• 2018

Aluminum nitride (AlN) is used by the semiconductor industry that has requirements for high thermal conductivity. The theoretical thermal conductivity of single crystal AlN is 320W/mK. Whereas, the values measured for polycrystalline AlN ceramics range from 20 W/mK to 280 W/mK. The variability is strongly dependent upon the purity of the starting materials and non-uniform dispersibility of the sintering additive. The conventional AlN sintering additive used yttria ($Y_2O_3$), but the dispersibility of the powder in the mixing process was important. In this study, we investigated the mechanical and thermal conductivity of yttrium nitrate ($Y(NO_3)_3{\cdot}6H_2O$), as a sintering additive in order to improve the dispersibility of $Y_2O_3$. The sintering additives content was in the range of 2 to 4.5wt.%. The density of AlN gradually increased with increasing contents of sintering additive and the flexural strength gradually increased as well. The flexural strength of the sintered body containing 4 wt% of $Y_2O_3$ and $Y(NO_3)_3{\cdot}6H_2O$ was 334.1 MPa and 378.2 MPa, respectively. The thermal conductivities were 189.7W/mK and 209.4W/mK, respectively. In the case of hardness, there was only a slight difference and the average value was about 10 GPa. Therefore, densification, density and strength values were found to be proportional to its content. It was confirmed that AlN using $Y(NO_3)_3{\cdot}6H_2O$ displayed relatively higher thermal conductivity and mechanical properties than the $Y_2O_3$.