• Korean Journal of Metals and Materials
• /
• v.49 no.9
• /
• pp.678-685
• /
• 2011

The aim of this study was to determine the effect of applied pressure and sintering temperature on the microstructure and mechanical properties for spark plasma sintering (SPS) from commercial pure titanium (CP-Ti) powders. Spark plasma sintering is a relatively new sintering technique in powder metallurgy which is capable of sintering metal and ceramic powers quickly to full density at a fairly low temperature due to its unique features. SPS of -200 mesh or -400 mesh CP-Ti powders was carried out in an $Ar+H_2$ mixed gas flowing atmosphere between $650^{\circ}C$ and $750^{\circ}C$ under 10 to 80 MPa pressure. When SPS was carried out at relatively low temperatures ($650^{\circ}C$ to $750^{\circ}C$), the high (>60 MPa) pressure had a marked effect on densification and grain growth suppression. The full density of titanium was achieved at temperatures and pressures above $700^{\circ}C$ and 60 MPa by spark plasma sintering. The crystalline phase and microstructure of titanium sintered up to $700^{\circ}C$ consisted of ${\alpha}$-Ti and equiaxed grains. Vickers hardness ranging from 293 to 362 Hv and strength ranging from 304 to 410 MPa were achieved for spark plasma sintered titanium.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.4
• /
• pp.213-221
• /
• 2023

The demand for Liquefied Natural Gas (LNG) carriers and LNG-fueled ships has significantly increased in recent years due to the sulfur-oxide emission regulations by the International Maritime Organization (IMO). The main goal of this paper is to introduce the process for the Engineering Critical Assessment (ECA) of IMO independent type-B cargo tanks made from 9% nickel alloy. A methodology proposed by the British Standard was used to conduct ECA for any structure with initial flaws. Based on this standard, a Matlab code was developed to perform ECA. Coarse mesh Finite Element Analysis (FEA) was performed on an independent type-B LNG cargo tank with a capacity of 15,000 m³. The location with the highest development of maximum principal stress was identified at the bottom of the cargo tank. Fine mesh FEA was performed to obtain the stress range required for ECA. The dynamic cargo tank loads used for FEA were determined using some ship rules presented by Det Norske Veritas. As a result of performing a 20-year long-term crack propagation analysis with a semi-elliptical surface crack, the fracture-to-yield ratio exceeded the Fracture Assessment Line (FAL) and some structural reinforcement was necessary. Performing a 15-day short-term crack propagation analysis, the fracture-to-yield ratio remained within the FAL, and no significant LNG leaks were expected. This paper is believed to provide a guide for performing ECA of LNG cargo tanks in the future by providing the basic theory and application sample necessary to perform ECA.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.55-60
• /
• 2011

In the present work, isogeometric analysis in linear elasticity problem is conducted using the basis functions from NURBS. The objectives of isogeometric analysis introduced is to integrate both geometric modeling(CAD) and computational analysis(CAE), and this can be accomplished from direct usage of geometric modeling by NURBS as the computational mesh. The merit of the isogeometry analysis is that NURBS surface are able to represent exact geometry from the control points and knot vectors, and also subsequent refinement is relatively simple relatively. In order to verify the computer codes developed in this study, it has been applied to two structural models of which geometry are simple ; 1) circular cylinder subjected to the constant internal pressure loading, 2) square plate with circular hole at center subjected to uniform tension. The exact solutions of these two models are available. Convergence of the approximate solutions by the present code for the isogeometry analysis are investigated by mesh refinement with inserting knots (h-refinement) and by mesh refinement with order elevation of the basis functions (p-refinement).

• Journal of the Korean institute of surface engineering
• /
• v.50 no.6
• /
• pp.510-515
• /
• 2017

In this study, a transient liquid phase sintering (TLPS) process of Ag pastes mixed with a fusible metal alloy of Bi58Sn42 with the melting temperature of $138^{\circ}C$, was examined. After screen printing of the Ag pastes with and without Bi58Sn42 powders on polyimide (PI) substrates, the electrodes were heat-treated at different temperatures in the range between 150 and $300^{\circ}C$ for 60 min in air. Comparing the electrical conductivity of the Ag pastes with and without Bi58Sn42 alloy powder after the heat treatment, it was manifested that the low melting temperature alloy definitely played a major role in an increased conductivity when it is added into the Ag pastes by providing more electrical conduction paths between Ag particles. This can be explained by the fact that capillary force of the melts of Bi58Sn42 can contribute to the rearrangement of the Ag particles during the heat-treatment inducing better connectivity between the Ag particles.

• The Korean Journal of Food And Nutrition
• /
• v.30 no.4
• /
• pp.635-643
• /
• 2017

The properties of rice were studied, and 8 rice flour cultivars were used to study the effect of particle size on the physicochemical properties, color value, RVA viscosities, water absorption index (WAI), and water solubility index (WSI) of rice flours. The mean particle size by the 3 particle size classification of 150 mesh, 200 mesh, and 250 mesh was, $90.75{\mu}m$, $60.73{\mu}m$, $39.94{\mu}m$, respectively. Thai rice had the highest amylose content and Samkwang rice had the lowest amylose content. Protein content of rice flours prepared was decreased as the particle size of rice flour decreased. In terms of color values, the L-value and the a-value of rice flour were increased as the particle size of rice flours decreased, while the b-value was decreased as the particle size of rice flours decreased. Using a rapid visco analyzer (RVA), the initial pasting temperature of Thai rice cultivar was found to be the highest; the peak viscosities of Sunpum cultivar and Misomi cultivar, and Samkwang rice were higher than those of other rice flours. The water absorption index and water solubility index were increased as the particle size of rice flour decreased. In order to use processed rice flour for the development of processed foods, proper characteristics of the cultivars and particle size should be considered.

• Journal of the Korean Society of Safety
• /
• v.30 no.4
• /
• pp.20-25
• /
• 2015

In general, the causes of the electrical fire are overcurrent, short circuit, poor contact, etc. This study is aimed to recognize the risk of electric arc to prevent electrical fires due to the conductive dust accumulated on the circuit breaker. The experiment was carried out by the method that conductive metal dust collected from the field is being accumulated on the experimental electrodes with gap of 13 mm until the arc is generated. In case that arc was generated, the amount of conductive dust was measured and the thickness was calculated. This experiments was conducted by particle size. In order to distinguish particle size, mesh size(60~100, 100~150, 150~200, 200~250mesh) was classified using a sieve. As the results of experiment for each of the particle sizes, it was confirmed that there is differences in the generation of arc depending on the thickness of dust accumulated.

• Transactions of Materials Processing
• /
• v.12 no.1
• /
• pp.60-65
• /
• 2003

HIP diffusion bonding of Ni-based superalloys, cast Mar-M247 (MM247) and Udimet 720 (U720) powder, was experimentally and numerically studied. Subsolvus HIP treatment was optimized by investigating the variations of high temperature tensile properties of HIP-bonded specimens with powder size, HIP'ing time, etc. While the tensile strength at high temperatures showed no detectable changes, the tensile elongation and reduction in area were slightly increased as the powder size decreased from -140 mesh to -270 mesh. While as-HIP'ed U720 showed a high tensile strength comparable to that of lorded U720 alloy, the HIP diffusion-bonded specimen showed a strength lower than the forged U720 alloy and the cast MM247 alloy The increase of HIP'ing tune from 2 hours to 3 hours resulted in a rapid risc of tensile strength and elongation due to the disappearence of microvoids in the cast MM247. FEM simulation for HIP process was conducted by applying the McMeeking micromechanical model, which uses power-law creep model as constitutive equations. ABAQUS user subroutine CREEP with an implemented microscopic model was used for the simulation. Numerical simulation was shown to be essential for the near-net shape manufacturing as well as the HIP process optimization.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.8-16
• /
• 2001

To manufacture toilet tissue with ONP (old newspaper), the effect of fractionation fiber (R150, R100, R70 mesh) and bleaching(P, PY), blending (70/30) with MOW(mixed office wastepaper) or WL(white ledger) and the addition of softener on the optical and mechanical properties were studied. Considering the pulp yield, brightness and strengths, fibers of R100 mesh fraction were proper to be produced to toilet paper from ONP. This pulp showed the pulp yield of 76.8%, brightness of 50.2% ISO and tensile index of 21.1 Nm/g. By the bleach with P and PY stages, the brightness of the pulps increased up to 60.3% ISO and 61.8% ISO, respectively. When blended with MOW (57.3% ISO) or WL (76.2% ISO), the brightness of the former increased up to 58.5% ISO, the latter up to 63.6% ISO. The strengths of pulp blended with WL were higher than those of fractionated pulp from 100% ONP, however there was no difference in strengths between fractionated pulp and blended pulp wth MOW. While the addition of softener improved the softness of paper, but it decreased strengths of pulp and extended dispersing time in water.

• Journal of Chest Surgery
• /
• v.15 no.2
• /
• pp.259-265
• /
• 1982

We have designed a new type of bubble oxygenator (KOREA-KIM VENOTHERM OXYGENATOR) made of PVC sheet and deforming mesh incorporated in the heat exchanger, and evaluated in experimental animal for the analysis of it`s efficiency. The Oxygenator has low priming volume with high flow rate up to 6 L/rain, and efficiency of heat exchanger was excellent as 1-$1.5^{\circ}C.$ using total cardiopulmonary bypass method under moderate to deep hypothermia. Average priming volume of 1317 ml with 30% hemodilution method was perfused with an average of 1.1-3.0 L/min.$M^2$of arterial blood and pure oxygen at a rate of 2-3.4 L/min for 49.6 minutes continuously in average. During total cardiopulmonary bypass, average $PaO_2$ was $159.8{\pm}60$mmHg, $PaCO_2$ $41.0{\pm}3$mmHg respectively under $SaO_2$ over 96% with systolic arterial pressure of 70 mmHg and CVP of 5-10 cm$H_2O$. Plasma free Hemoglobin was $7.0{\pm}4$ mg/dl with 25% drop of hemoglobin and hematocrit at the end of cardiopulmonary bypass. This KKV Oxygenator was observed to have excellent capabillty of oxygen and carbon dioxide gas transfer with small amount of blood trauma, and the efficiency of heat exchanger was satisfactory during cooling and rewarming of the bubbled blood. Disadvantages have included the somewhat poor deforming effect due to loose PVC fiber mesh, the extracompact character of Teflon filters, and the rough inner surface of the heat exchanger copper pipes.

• The Journal of Engineering Research
• /
• v.7 no.1
• /
• pp.53-60
• /
• 2005

Community Wireless Networks define the next generation wireless services. Multimedia usages for financial services over community Wireless LAN (WLAN) based mesh networks require link stability. Several new services are being proposed for multimedia over WLANs. Portable Internet Services are implemented by several wireless carriers to proliferate their customer base. However, these services are still expensive and require a central telecom/wireless carrier whose monopoly and preference defines the availability of new services. Our research project identifies the usage of these critical services in public places over the financial services backbone architecture to provide efficient easy-to-use and economical services to their customers and merchants without being dependent on the central wireless carrier. The user connects to the network using his regular WLAN NIC using the Mesh Router/Bridge interconnectivity and obtains the needed multimedia and financial services from the ATM-AP Gateway, In our proposed scenario, the ATN AP-MR use AODV protocol and MR-MC is based on 802.11g/a/b IEEE standard. We use multi path routing protocols for reducing the congestion over a particular route. We demonstrate the results of our simulations and test-bed outcome to evaluate link failure rate and oversubscription factors to eliminate network congestion and non-availability of the critical financial services.