• ETRI Journal
• /
• v.36 no.6
• /
• pp.924-930
• /
• 2014

This paper presents a $0.13{\mu}m$ CMOS 3-level envelope delta-sigma modulation (EDSM) RF signal generator, which synthesizes a 2.6 GHz-centered fully symmetrical 3-level EDSM signal for high-efficiency power amplifier architectures. It consists of an I-Q phase modulator, a Class B wideband buffer, an up-conversion mixer, a D2S, and a Class AB wideband drive amplifier. To preserve fast phase transition in the 3-state envelope level, the wideband buffer has an RLC load and the driver amplifier uses a second-order BPF as its load to provide enough bandwidth. To achieve an accurate 3-state envelope level in the up-mixer output, the LO bias level is optimized. The I-Q phase modulator adopts a modified quadrature passive mixer topology and mitigates the I-Q crosstalk problem using a 50% duty cycle in LO clocks. The fabricated chip provides an average output power of -1.5 dBm and an error vector magnitude (EVM) of 3.89% for 3GPP LTE 64 QAM input signals with a channel bandwidth of 10/20 MHz, as well as consuming 60 mW for both channels from a 1.2 V/2.5 V supply voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.8
• /
• pp.740-747
• /
• 2015

Recently, mobile communication systems using the millimeter-wave frequency band have been proposed, and the importance of efficient compensation of the nonlinearity caused by 60 GHz high-power amplifiers(HPAs) is increasing. In this paper, we propose a predistorter structure based on multiple coefficient sets which are separately used to different ranges of input power values. These ranges correspond to varying levels of nonlinearity characteristics. The structure is applied to the 60 GHz HPA FMM5715X and the performance of correcting the nonlinearity of LTE signals is evaluated. Evaluation results using a hardware testbed demonstrate that the proposed predistorter structure achieves the maximum of 6 dB gain over the conventional method in terms of the adjacent channel leakage ratio(ACLR).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.599-609
• /
• 2000

In this paper, sub-harmonically pumped single balanced resistive mixers are presented . Frequency bandwidth is selected for a Ku-band, which is 11.75-12.25GHz for RF, 5.375∼5.625 GHz for LO, and 1 GHz for IF signals. A rat-race hybrid is designed for the accomplishment of single balanced type. A low pass filter (LPF) with photonic band gap(PBG) structure is used for good conversion loss and unwanted harmonics suppression. Two types of mixers are suggested, which are one with no gate bias for no DC power consumption and the other with the IF amplifier for conversion gain. When a LO signal with the power of 6 dBm at 5.5 GHz is injected, a conversion loss of 12.17dB and a conversion gain of 7.83 dB are obtained for each mixer. For the both mixers , LO to RF isolation of 20 dB and LO to IF isolation of 60dB are obtained. With the RF power of -30dBm to -3dBm, the mixer shows linear characteristics region of IF. this mixer can be applied for Ku-band and other microwave communication systems.

• Journal of the Institute of Convergence Signal Processing
• /
• v.13 no.1
• /
• pp.39-43
• /
• 2012

60GHz band RF transceiver was made with the NRD waveguide structure for the point- to-point communication. A dielectric line that of comprising NRD waveguide was the milling process was not easy because a material gets soft, and also compression and expansion according to a temperature were serious, so this line was not suitable for the device in which the resonance characteristic was important. In addition, the thing for comprising amplification module was difficult in the NRD waveguide structure. In this paper, a way in which to overcome mentioned in upper part, the transceiver was made by below technology. Components in which the resonance characteristic was not important were made with the NRD waveguide hybrid IC, and components in which the resonance characteristic was important were made with waveguide. An amplifier packaged and modularizing the bare chip, it equipped at the NRD waveguide within. Manufactured transceiver communicated with FDD method, and it had 10dBm output power, and -60dBm minimum receive sensitivity.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.168-171
• /
• 2010

본 논문에서는 GaN HEMT 소자를 이용한 고출력 고효율 특성을 가지는 광대역 SSPA의 개발을 다루고 있다. 개발한 SSPA는 8W 급과 15W 급의 GaN HEMT 소자를 사용하여 Pre-Drive 증폭단을 구성하였으며, Drive 증폭단은 50W/150W급 GaN HEMT 소자를 직/병렬구조로 사용하였다. Main 증폭단은 4-way 분배기와 결합기를 이용한 Balanced Structure를 적용하여 높은 출력을 구현하였으며, 안정적인 동작을 위하여 음(-)전원 제어 회로와 출력신호 검출 회로를 포함하고 있다. 제작된 SSPA의 사용가능 대역은 2.9GHz~3.3GHz로 단일전원을 사용하고 있으며 100us 펄스 폭, 10% Duty Cycle 조건에서 60dB의 전압이득, 1kW 출력과 약 28% 효율 특성을 가지는 것으로 측정되었다. 본 논문에서 개발한 SSPA는 S-대역을 사용하는 레이더시스템의 송신단에 적용될 수 있다.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.425-425
• /
• 2006

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.339-342
• /
• 2004

본 논문은 밀리미터파 대역 무선통신 시스템 송신부의 응용을 위해 CPW 구조를 이용하여 V-band용 상향 주파수 혼합기와 2단 구동증폭기를 설계$\cdot$제작하였다. 능동소자는 본 연구실에서 제작한 $0.1{\mu}m$ 게이트 GaAs Pseudomorphic HEMTs(PHEMTs)를 사용하였으며 입$\cdot$출력단은 CPW를 사용해 정합 회로를 설계하였다. 제작된 상향 주파수 혼합기는 LO power 5.4 dBm, 2.4 GHz IF 신호를 -10.25 dBm으로 입력하였을 때 Conversion Loss 1.25 dB, LO-to-RF Isolation은 58 GHz에서 13.2 dB의 특성을 나타내었다 2단 구동 증폭기는 측정결과 60 GHz에서 S21 이득 13 dB, $58\;GHz\;\~\;64\;GHz$ 대역에서 S21 이득 12 dB 이상을 유지하는 광대역 특성을 얻었고 증폭기의 Pl dB는 3.8 dBm, 최대 출력전력은 6.5 dBm의 특성을 얻었다.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.18-23
• /
• 2006

In this paper, we demonstrate a fully integrated X-band image rejection down converter, which was developed using InGaP/GaAs HBT MMIC technology, consists of two single-balanced mixers, a differential buffer amplifier, a differential YCO, an LO quadratue generator, a three-stage polyphase filter, and a differential intermediate frequency(IF) amplifier. The X-band image rejection downconverter yields an image rejection ratio of over 25 dB, a conversion gain of over 2.5 dB, and an output-referred 1-dB compression power$(P_{1dB,OUT})$ of - 10 dBm. This downconverter achieves broadband image rejection characteristics over a frequency range of 1.1 GHz with a current consumption of 60 mA from a 3-V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.53-60
• /
• 2010

This paper presents a novel gain control system composed of a feedback circuit, Two stage Low Noise Amplifier (LNA) using 0.18 um CMOS technology for 5.2 GHz. The feedback circuit consists of the seven function blocks: peak detector, comparator, ADC, IVE(Initial Voltage Elimination) circuit, switch, storage, and current controller. We focus on detecting signal and designing storage circuit that store the previous state. The power consumption of the feedback circuit in the system can be reduced without sacrificing the gain by inserting the storage circuit. The adaptive front-end system with the feedback circuit exhibits 11.39~22.74 dB gain, and has excellent noise performance at high gain mode. Variable gain LNA consumes 5.68~6.75 mW from a 1.8 V supply voltage.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.181-184
• /
• 2002

본 논문에서는 600Hz 무선 LAN 시스템에 탑재를 위한 600㎓ 대역 전력증폭기 모듈을 개발 하였다. 600㎓ 대역 전력증폭기 모듈에 실장된 600㎓ 대역 전력증폭기 MMIC는 ETRI에서 설계 및 제작한 것으로 칩의 크기는 2.80 × 1.75㎟이며, on-wafer측정을 하여 얻은 결과는 동작 주파수 58~620Hz에서 소신호 이득은 12.4dB이고, 최대 소신호 이득은 59~60G보z에서 ISdB이며, 출력전력(Pldn)은 16.3~16.7dBm을 얻었다. 이와 같은 특성을 갖는 전력증폭기 MMIC를 사용하여 모듈을 제작하였으며, RF feed line을 위해 Rogers 사의 R03003 기판을 사용하였다. 모듈의 입출력은 동작 주파수 대역에 적합한 WRl5라는 waveguide 형태를 사용하였고, DC 바이어스 공급을 위해 3.5㎜ K-connector를 사용하였다 제작한 모듈의 크기는 40 × 30 × 15㎣이며, 최적의 성능을 얻고자 tuning bar를 상하로 이동하여 최적점을 찾았으며 나사로 고정하여 상태를 유지하도록 하였다. DC 바이어스 및 RF feed line과 칩의 연결은 본딩에 의한 인덕턴스를 최소화하기 위하여 3mil 두께의 리본 본딩을 하였다 전력증폭기 모듈을 측정한 결과, 동작주파수 600㎓ 대에서 소신호 이득은 6dB 이상, 입력 정합은 -lOdB 이하, 출력 정합은 -4dB 이하로 측정되었긴, 출력전력은 SdBm 이상으로 측정되었다. 동국대에서 제작한 600Hz 무선 LAN 시스템에 전력증폭기 모듈을 시스템 송신부에 탑재 시험한 결과, 동영상을 실시간으로 전송하는데 성공하였다.