• 한국가스학회지
• /
• 제19권1호
• /
• pp.18-22
• /
• 2015

본 연구는 LPG 강재용기에서 상단반구와 하단반구의 코너반경이 응력강도 안전성에 미치는 영향을 FEM으로 해석한 것이다. FEM 해석결과에 의하면, 응력강도 안전성에 큰 영향을 미치는 요소는 용기의 두께보다 상단반구 및 하단반구의 코너반경이다. 그러나 강재용기의 두께는 경량화에 직결되기 때문에 간과해서는 안 되는 중요한 설계요소이다. LPG 강재용기의 강도안전성 검사에서 최고시험압력이 3.04MPa임을 감안할 때, 20kg용 LPG 강재용기의 두께는 2.3~2.6mm, 상단반구와 하단반구의 코너반경은 157mm 이상으로 최적화 설계하는 것이 바람직함을 알 수 있다.

• Nuclear Engineering and Technology
• /
• 제43권1호
• /
• pp.75-82
• /
• 2011

The neutron multiplication factor in spent fuel storage racks, in which a stainless steel plate encloses a fuel assembly, was evaluated according to the variation of distance between the fuel assembly and stainless steel plate, as well as the pitch. The stainless steel plate position with the lowest multiplication factor on each pitch consistently appeared as 6mm or 9mm away from the outmost surface of the fuel assembly. Because the stainless steel plate has a thermal neutron absorption cross section, its ability to absorb neutrons can work best only if it is installed at the position where thermal neutrons can be gathered most easily. Therefore, the stainless steel plate position should not be too close or too far away from the fuel assembly, but it should be kept a pertinent distance from the fuel assembly.

• 교육녹색환경연구
• /
• 제10권2호
• /
• pp.1-7
• /
• 2011

An experimental study to evaluate structural capacity of an embedded plate connected with prestressed concrete beam was performed. Embedded steel plates and prestressed concrete beam were connected with stud-bolts at the ends of concrete beam specimens. About 1,000 kN concentrated load was applied at 450mm away from the end of beam specimen. A 3,000 kN capacity static Oil-jack was used to direct concentrated load. The maximum strain of stud-bolt recorded $90{\times}10^{-6}$(mm/mm) and wide width cracks were not founded. Any falling failures of concrete and large deformations were not founded either between steel plate and prestressed concrete specimen. As a result, construction performance can be improved using this embedded steel plate connection system apply to large space educational facilities.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.494-499
• /
• 2009

As a novel method to produce a steel beam with 6mm thickness for buildings, a continuous roll forming process is reported. The roll shape is asymmetric and consists of 6 pairs of rollers to bend the steel plate from $0^{\circ}$ to $90^{\circ}$. Results obtained upon application of the roll forming process showed that the angle of the section plate is $90^{\circ}$. However, defects such as bowing and camber as high as 3.2 [$^{\circ}/m$] were observed. A FEM (Finite Element Method) analysis was applied to investigate the causes of the results for the region between rollers no. 5 and no. 6. The results of a FEM simulation of deformation and stress showed that there are some strong peak stresses on the upper surface and bottom surface of the material. The positions of the peak stresses did not show a correspondence between the upper and bottom surfaces. Thus, the defects in the process of roll forming with a 6 mm thick steel plate occur by the unbalanced stresses between the upper surface and bottom surface of the material in this study.

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.735-751
• /
• 2012

Although being one of the most popular strengthening techniques in reinforced concrete beams, the use of steel plates bonded to the soffit raises problems of ductility. This study aims at investigating the influence of the use of perforated steel plates instead of solid steel plates on the ductility of reinforced concrete beams. A total of nine reinforced concrete beams were tested. In addition to an unplated beam, eight beams with perforated steel plates of two different thicknesses (3 mm and 6 mm) were subjected to monotonic loading. Effect of bonding the plates to the beams with anchor bolts and with additional side plates bonded to the sides of the beam with and without anchors is also investigated. The use of bolts in addition to epoxy was found to greatly contribute to the ductility and energy absorption capacity of the beams, particularly in specimens with thick plates (6 mm) and the use side plates in addition to the bottom plate was found to be ineffective in increasing the ductility of a concrete beam unless the side plates are attached to the beam with anchors bolts. The thickness of the plate was found to have little effect on the bending rigidity of the beam.

• 한국강구조학회 논문집
• /
• 제23권6호
• /
• pp.705-713
• /
• 2011

본 연구의 목적은 기존의 데크플레이트 슬래브에 오메가형 강판을 중공체로 사용한 데크플레이트 슬래브의 진동 및 내화성능을 평가하는 것이다. 오메가형 강판의 삽입으로 인한 데크플레이트 슬래브의 진동 성능을 평가하기 위해서 슬래브 두께를 주요 변수로 하였으며, 각각 150mm 실험체 3개와 200mm 실험체 3개를 제작하였다. 각 실험체는 슬래브 두께별로 기존의 데크플레이트 슬래브 1개와 콘크리트 토핑두께(오메가형 강판의 높이)를 변수로 하는 2개의 실험체로 구성되어 있다. 또한 내화성능을 평가하기 위해서 실물크기의 실험체 2개(동일 크기)를 제작하였다. 진동에 대한 실험결과 오메가형 강판이 삽입된 철선일체형 데크플레이트 슬래브는 고유진동수가 12.66Hz~14.09Hz로써 중공부로 인한 진동문제는 없는 것으로 나타났다. 또한 내화성능에 대한 실험 결과 각 실험체는 실험시간 2시간 동안 하중지지력, 차열성, 차염성에 대한 평가기준을 모두 만족하였다. 따라서 오메가형 강판을 삽입한 철선일체형 데크플레이트는 효과적으로 콘크리트 사용량을 저감하면서도 기존의 데크플레이트에 준하는 진동 및 내화성능을 갖춘 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• 제55권12호
• /
• pp.4637-4641
• /
• 2023

For nuclear decommissioning applications, a study was conducted to investigate the feasibility of using a laser for long-distance cutting in complex structures. Cutting tests were performed on stainless steel plates with thicknesses ranging from 10 mm to 30 mm at distances of 300 mm-700 mm from the laser head, using a laser power of 6 kW. Remarkably, the 10 mm and 20 mm thick stainless-steel plates were successfully cut at a distance of 700 mm from the head. Based on the trends observed in the results, it is anticipated that these thicknesses could also be cut at distances of approximately 1 m. Similarly, the 30 mm thick stainless-steel plate was effectively cut at a distance of 500 mm from the head. To evaluate the amount of secondary waste generated, the kerf width was measured. Due to the long-distance cutting, the average kerf width ranged from 6 mm to 16 mm. Despite the wider kerf width, long-distance cutting holds promise for efficiently handling hard-to-reach targets in nuclear decommissioning scenarios.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.145-155
• /
• 1995

Continuous wave C $O_{2}$ laser beam welding and formability of zinc coated steel plates were investigated. First, the optimal welding condition could be obtained in lap configuration by using the data for heat input, gap size and fracture behaviour. The gap size for fully-penetrated bead could be predicted by the gap model by Akhter et al. AIso, it was found that the joining efficiency was constant. Secondly, the butt welding of dissimilar materials (zinc coated steel plate and cold rolled steel plate) with different thicknesses was investigated. In the thickness range of 0.8-2.0 mm, the maximum welding speed of 10m/min was obtained. In the butt welding of two plates with thickness 2.0 mm and l.6mm, the maximum, welding speed of 6m/min was obtained, Finally. the forming results of butt-welded plates showed that the joining design was important to apply the laser welded blank in the automotive production.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.149-154
• /
• 2003

The cutting tests of high tensile steel plate(AH36) were carried out using CNC plasma arc cutting machine. Both top and bottom width of kerf and the surface roughness(Ra, Rmax) of cut surface are measured under various cutting conditions such as cutting speed, steel plate thickness, etc. In the CNC plasma arc cutting, the surface roughness decreases as cutting speed increases. The hardness is high up to 4mm depth from the cutting surface. In the cutting speed 1300~2100mm/min, the ratio of proper kerf width(Wt/Wb) is around 2.6. Through the series the series of experiments, the satisfactory cutting conditions of high tensile steel plate were found.

• Steel and Composite Structures
• /
• 제32권5호
• /
• pp.571-582
• /
• 2019

This study aimed to assess the feasibility on the wide and long 9%Ni steel plate for use in the LNG storage inner tank shell. First, 5-m-wide and 15-m-long 9%Ni steel plates were test manufactured from a steel mill and specimens taken from the plates were tested for strength, toughness, and flatness to verify their performance based on international standards and design specifications. Second, plates with a thickness of 10 mm and 25 mm, a width of 4.8~5.0 m, and a length of 15 m were test fabricated by subjecting to pretreatment, beveling, and roll bending resulting in a final width of 4.5~4.8 m and a length of 14.8m with fabrication errors identical to conventional plates. Third, welded specimens obtained via shield metal arc welding used for vertical welding of inner tank shell and submerged arc welding used for horizontal welding were also tested for strength, toughness and ductility. Fourth, verification of shell plate material and fabrication was followed by test erection using two 25-mm-thick, 4.5-m-wide and 14.8-m-long 9%Ni steel plates. No undesirable welding failure or deformation was found. Finally, parametric design using wide and long 9%Ni steel plates was carried out, and a simplified design method to determine the plate thickness along the shell height was proposed. The cost analysis based on the parametric design resulted in about 2% increase of steel weight; however, the construction cost was reduced about 6% due to large reduction in welding work.