• Journal of ILASS-Korea
• /
• v.3 no.4
• /
• pp.35-42
• /
• 1998

Laser Raman scattering method has been applied to measure equivalence ratio of methane/air and propane/air mixture in constant volume combustion chamber. We used high power KrF excimer laser$(\lambda=248nm)$ and a high gain ICCD camera to capture low intensity Raman signal. Raman shifts and Ram cross-sections of $H_2,\;O_2,\;N_2,\;CO_2,\;CH_4\;and\;C_3H_8$ were measured precisely. Our results showed an excellent agreement with other groups. Mole fraction measurement of $O_2\;and\;N_2$ from air showed that $O_2\;:\;N_2$ = 0.206 : 0.794. We used constant volume combustion chamber and gas injector which is operated at $5\sim10barg$. Methane and propane are used as a fuel. 50 Raman signal are obtained and ensemble averaged for measurement of equivalence ratio. Our measured results showed that the equivalence ratio of fuel/air mixture is reasonable at ${\pm}5%$ error range.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.251-265
• /
• 2000

S $m_{2}$F $e_{17}$ $N_{x}$ film magnets using a S $m_{2}$F $e_{17}$ target were prepared at $N_{2}$ gas atmosphere using a Nd-YAG laser ablation technique. The effect of nitrogen pressure, deposition temperature, pulsation time and film thickness on the structure and magnetic properties of S $m_{2}$F $e_{17}$ $N_{x}$ film were studied. Increasing the nitrogen pressure up to 5 atm. was confirmed to lead the formation of complete S $m_{2}$F $e_{17}$ $N_{x}$ compound. Optimized magnetic properties with the nitrogenation temperature ranging over 500-53$0^{\circ}C$ could be obtained by extending the nitrogenation time up to 4 hours. Relatively low coercivities of 400~600 Oe were exhibited from the S $m_{2}$F $e_{17}$ $N_{x}$ films having the thickness of 50~100 nm while 4$\pi$ $M_{s}$ of 10~12 kG could be achieved. In-plane anisotropic characteristic, which was the basic goal in this study, was achieved by controlling the nitrogenation parameters.ameters.ers.ameters.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1993-1997
• /
• 2012

Mg-doped ZnO one-dimensional (1D) nanostrutures were synthesized by using a thermal evaporation technique. The morphology, crystal structure, and sensing properties of the Mg-doped ZnO nanostructures functionalized with Pt to CO gas at $100^{\circ}C$ were examined. The diameters of the 1D nanostructures ranged from 80 to 120 nm and that the lengths were up to a few tens of micrometers. The gas sensors fabricated from multiple networked Mg-doped ZnO nanowires functionalized with Pt showed enhanced electrical response to CO gas. The responses of the nanowires were improved by approximately 70, 69, 111, and 81 times at CO concentrations of 10, 25, 50, and 100 ppm, respectively. Both the response and recovery times of the nanowire sensor for CO gas sensing were not nearly changed by Pt functionalization. It also appeared that the Mg doping concentration did not influence the sensing properties of ZnO nanowires as strongly as Pt-functionalization. In addition, the mechanism for the enhancement in the CO gas sensing properties of Mg-doped ZnO nanowires by Pt functionalization is discussed.

• Particle and aerosol research
• /
• v.9 no.2
• /
• pp.51-57
• /
• 2013

A graphene(GR)-$TiO_2$ composite was synthesized from colloidal mixture of graphene oxide(GO) nanosheets and $TiO_2$ nanoparticles by an aerosol assisted self-assembly. The morphology, specific surface area and pore size of asprepared GR-$TiO_2$ composite were characterized by FE-SEM, BET, and BJH respectively. The shape of GR-$TiO_2$ composite was spherical. The average particle size was 0.5-1 ${\mu}m$ in diameter and the pore diameter ranged 20-50 nm. Photovoltaic characteristics of a mixture of the GR-$TiO_2$ and $TiO_2$ nanoparticles were measured by a solar simulator under simulated solar light. The highest photoelectric conversion efficiency of the mixture photoanode was 5.1%, which was higher than that of $TiO_2$ photoanode.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.73-81
• /
• 2011

We manufactured the inkjet printing system for the application into the nano Ag finger line interconnection process in Si solar cells. The home-made inkjet printer consists of motion part for XY motion stage with optical table, head part, power and control part in the rack box with pump, and ink supply part for the connection of pump-tube-sub ink tanknozzle. The ink jet printing system has been used to conduct the interconnection process of finger lines on Si solar cell. The nano ink includes the 50 nm-diameter. Ag nano particles and the viscosity is 14.4 cP at $22^{\circ}C$. After processing of inkjet printing on the finger lines of Si solar cell, the nano particles were measured by scanning electron microscope. After the heat treatment at $850^{\circ}C$, the finger lines showed the smooth surface morphology without micropores.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.45-50
• /
• 2020

We investigated the Si_1-xGe_x surface properties when dry cleaning the films using NF₃ / H₂O remote plasma. After the dry cleaning process, it was found that about 80-250 nm wide bumps were formed on the SiGe surface regardless of Ge concentration in the rage of x = 0.1 ~ 0.3. In addition, effects of the dry cleaning processing parameters such as pressure, substrate temperature, and H₂O flow rates were examined. It was found that the surface bump is significantly dependent on the flow rate of H₂O. Based on these observations, we would like to provide additional guidelines for implementing the dry cleaning process to SiGe materials.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.12a
• /
• pp.154-155
• /
• 2005

Multi-layer film of $MgO/(FePt-B)_{50nm}/ MgO$ was deposited on Si(100) substrates by RF magnetron sputtering. The boron chips were uniformly placed oil tile FePt target. The boron content of thin film was found to be about 5, 10, 15, 25 and $33 at\%$ by using a CAMECA SX-51 wavelength dispersive spectroscopy (WDX). It is observed that X-ray diffraction patterns of FePt-B film by post-annealing exhibited a transformation from disordered fcc structure to ordered $Ll_0$ phase with fct structure from around $400^{\circ}C$. By adding B, annealing temperature for ordering is about $200^{\circ}C$ lower than that of pure FePt. This remarkable decrease of the annealing temperature is closely related to the high diffusivities of Fe and Pt associated with the defects caused by movements of B atoms. The maximum coercivity(Hc) for FePt films was found to be ${\~}$13 kOe after annealing at $600^{\circ}C$ for 1hr.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.207-213
• /
• 2014

A study was carried out to fabricate the cutting tool geometry with micro/nanoscale on the single crystal diamond tool by using the FIB. The FIB technique is an ideal tool for TEM sample preparation that allows for the fabrication of electron-transparent foils. The FIB is appropriate techniques to sample and subsequently define the chemical composition and the structural state of mineral inclusion on the micro/nanoscale. The combination of FIB with a SEM allows for 3D information to be obtained from samples including 3D imaging. Cutting strategies were demonstrated to improve the performance of cutting tool geometry and to generate high aspect ratio micro cutting tool. A finely focused beam of 30keV Ga+ ions was used to mill cutting tool shapes for various micro patterns. Therefore FIB sputtering is used to shape a variety of cutting tools with dimensions in the $1-5{\mu}m$ range and cutting edge radii of curvature of under 50nm.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.277-283
• /
• 2014

This paper presents the design, optimization and fabrication of a piezo driven micro-positioning stage constructed using a 3D-printer. 3D printing technology provides many advantageous aspects in comparison to traditional manufacturing techniques allowing more rapid prototyping freedom in design, etc. Micro-positioning stages have traditionally been made using metal materials namely aluminum. This paper investigates the possibility of fabricating stages using ABS material with a 3D printer. CAE simulations show that equivalent motion amplification can be achieved compared to a traditional aluminum fabricated stage while the maximum stress is 30 times less. This leads to the possibility of stages with higher magnification factors and less load on the driving piezo element. Experiment results agree with the simulation results. A micro-position stage was fabricated using a 3D printer with ABS material. The motion amplification is very linear and 50 nm stepping was demonstrated.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.45-50
• /
• 2007

The aspheric lens has become the most popular optical component used in various optical devices such as digital cameras, pick-up lenses, printers, copiers etc. Using aspheric lenses not only miniaturizes and reduces the weight of products, but also lower prices and higher field angles can be realized. Additionally, plastic lenses are being changed to glass lenses more recently because of low accuracy, low acid-resistance and low thermal-resistance in the plastic lenses. Currently, one fabrication method of glass lenses is using a glass-mold method with a high precision mold core for mass production. In this paper, DOE (Design Of Experiments) and compensation machining were adopted to improve the surface roughness and the form accuracy of the mold core. The DOE has been done in order to discover the optimal grinding conditions which minimize the surface roughness with factors such as work spindle revolution, turbine spindle revolution, federate and cutting depth. And the compensation machining is used to generate high form accuracy of the mold core. From various experiments and analyses, we could obtain the best surface roughness 5 nm in Ra, form accuracy $0.167\;{\mu}m$ in PV.