• International Journal of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.109-114
• /
• 2018

In order to improve performance for the size of the BLPD, the CCL is used for the realization as the delay line. As realizing lower coupling coefficient and lower characteristic impedance, the CCL has good performance of the phase delay. The CCL is applied as the compact BLPD with optimized coupling factor and matched impedance because the lower coupling coefficient and lower characteristic impedance are increased the size and the loss, respectively. Designed BLPD using the CCL has the size of $0.13{\lambda}_g{\times}0.13{\lambda}_g$ and the size-reduction ratio of fabricated BLPD using the CCL has 58.5% ($21.08{\times}21.40mm^2$). Also, fabricated BLPD is measured the insertion loss of 3.16dB at the center frequency of 1.78GHz and the 20dB bandwidth is 9.58%. Differenced magnitude and phase between threw port and coupled port are measured 0.1dB and $89.9^{\circ}$, respectively. These performances are almost same compared with the conventional BLPD. Suggested application of the CCL can be used various devices and circuits for the size-reduction.

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.55-61
• /
• 2006

The microwave dielectric properties and low temperature sintering of $Ca[Ti_{1-x}(Ni_{1/3}Nb_{2/3})_x]O_3$ system were investigated at the sintering temperature $1,200\~1,350^{\circ}C$. The density and quality factors $(Q{\times}f)$ increased while dielectric constants slightly decreased with the decrease of Ti. The dielectric constant, quality factor, and temperature coefficient of resonance frequency $(\tau_f)$ were 64, 17,000 GHz, and $-9.1\;ppm/^{\circ}C$ respectively, when $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ ceramics were sintered at $1,300^{\circ}C$ for 4 h. $2Li_2O-B_2O_3$ was added to $CaTi_{1/2}(Ni_{1/3}Nb_{2/3})_{1/2}O_3$ to decrease the sintering temperature for LTCC application. The microwave dielectric properties of the samples sintered at $925^{\circ}C$ for 2 h with the addition of $6\;wt\%\;2Li_2O-B_2O_3$ were $\varepsilon_r=48.7,\;Q{\times}f=8,460\;GHz$, and $\tau_f=+5.6ppm/^{\circ}C$. Compatibility test of the composition with silver electrode shows no reaction with silver electrode, implying the feasibility as a high-K LTCC material.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.1-5
• /
• 2006

In this paper, the EM wave absorber was designed and fabricated for the collision-avoidance radar as a basic sensor of ITS(Intelligence Transport System), because radar system has some problems including false image and system-to-system interference. We fabricated some samples in different composition ratio of Carbon and CPE, and defined that optimum composition ratio of Carbon and CPE was 20:80 wt%. The complex relative permittivity was calculated by the measured data. And absorption abilities were simulated according to different thickness of the EM wave absorbers using the complex relative permittivity. The EM wave absorber was manufactured based on the simulated design. Simulated and measured results agree very well. As a result, the developed EM wave absorber with the thickness of 2 mm has absorption ability over 20 dB in frequency range of $76{\sim}77$ GHz.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.95-95
• /
• 2011

토양수분은 전 지구 및 기후 모델 연구, 전 지구 환경 감시, 기후변화, 대기-지표의 물과 에너지 상호교환 등 중요한 역할을 한다. 최근에는 수동형 마이크로웨이브 센서를 이용하여 토양수분을 탐지하고 있으며, NASA는 공식적인 전구 토양수분을 제공하고 있다. 특히, AMSR-E(Advandced Microwave Scanning Radiometer on EOS)의 6 GHz 영역에서 산출된 토양수분은 지표 토양층(0～5 cm)의 높으 정확도의 토양 수분 정보를 제공하고 있다. 지금까지의 위성관측을 이용한 토양 수분 알고리즘은 복잡한 선행모델과 관측된 경험식을 바탕으로 한다. 이 연구의 제안한 알고리즘은 위성에서 관측된 휘도온도 정보를 이용하여 역변환 방법을 이용하여 토양수분을 산출할 수 있기에, 복잡한 선행모델 사용을 최소화하는 장점이 있다. 본 연구에서 제시한 토양수분 산출 알고리즘은 각 채널(6.9 및 37 GHz)의 특성을 이용하여 거친 표면의 반사도를 산출한 후, 편광비율 특성을 이용한다. 아울러 반사도는 Hong 근사식을 이용하여 지표면 거칠기, 물질의 특성을 나타내는 유전상수를 산출하고 두 변수 사이의 관측된 경험적 관계식를 이용하여 전 지구적인 토양수분이 산출한다. 이 결과는 NASA에서 산출한 토양 수분과 현장관측 (SMEX03)의 오클라호마, 조지아 지역 관측 결과와 비교하였을 때, 사용자들이 요구하는 수준 (<0.06g/$cm^3$)의 정확도를 만족시킨다. 본 연구에서 제시된 토양수분 알고리즘은 단순성, 정확성, 물리적 기반을 바탕으로 하기에 현업용으로 그 활용 가치가 높다. 본 연구 결과는 향후 국외 토양수분산출 전용 위성들인 SMOS(Soil Moisture and Ocean Salinity)와 SMAP(Soil Moisture Active/Passive) 자료들을 생산하는데 활용된다면, 전 지구적 토양수분 정보제공에 기여할 수 있을 것으로 예산된다.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.181-185
• /
• 2007

For more than two decades Nb trilayer ($Nb/Al_2O_3/Nb$) process has been serving as the most stable fabrication process of the Josephson junction integrated circuits. Fast development of semiconductor fabrication technology has been possible with the recent advancement of the fabrication equipments. In this work, we took an advantage of advanced fabrication equipments in developing a superconducting Arithmetic Logic Unit (ALU) by using Nb trilayers. The ALU is a core element of a computer processor that performs arithmetic and logic operations on the operands in computer instruction words. We used DC magnetron sputtering technique for metal depositions and RF sputtering technique for $SiO_2$ depositions. Various dry etching techniques were used to define the Josephson junction areas and film pattering processes. Our Nb films were stress free and showed the $T{_c}'s$ of about 9 K. To enhance the step coverage of Nb films we used reverse bias powered DC magnetron sputtering technique. The fabricated 1-bit, 2-bit, and 4-bit ALU circuits were tested at a few kilo-hertz clock frequency as well as a few tens giga-hertz clock frequency, respectively. Our 1-bit ALU operated correctly at up to 40 GHz clock frequency, and the 4-bit ALU operated at up to 5 GHz clock frequency.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.305-310
• /
• 2002

The microwave dielectric properties of Ba(Mg$_{1}$3/Ta$_{2}$3/O$_3$-Ba(Co$_{1}$3/Nb$_{2}$3/O$_3$[BMT-BCN] ceramics were investigated. The specimens were prepared by the conventional mixed oxide method with the sintering temperature of 15$25^{\circ}C$~1575$^{\circ}C$. It was found that Ba(Mg$_{1}$3/Ta$_{2}$3/O$_3$[BMT] and BCN formed a solid solution with complex perovskite structure. As increasing the mole fraction of BCN, dielectric constant increased while the temperature coefficient of resonant frequency was changed from positive to negative value. The highest value of quality factor, Q$\times$f$_{0}$=138,205GHz, obtained in the 0.9BMT-0.1BCN ceramics sintered at 1575$^{\circ}C$. In the range of x$\geq$0.4, the dielectric constant was about 30. The 0.55BMT-0.45BCN ceramics sintered at 15$25^{\circ}C$ for 5 hours showed the microwave dielectric properties of $\varepsilon$$_{r}$=30.21, Q$\times$f$_{0}$=85,789GHz and $\tau$$_{f}$=2.9015ppm/$^{\circ}C$.EX>.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.646-651
• /
• 2012

This paper is about the experiment which is throughput of WLANs based on 802.11 due to interference each other. Recently, WLAN has been increased due to generalization of smart-phone and potable notebook. Therefore, the decrease of throughput because of interference between WLANs is expected. In regard of this, the throughput of WLANs according to channelling is measured in order to figure out efficient channelling and the throughput of WLANs according to the number of AP was measured in order to get relation between number of AP and throughput. Then, more efficient channelling of 1, 5, 9, 13 is suggested and the throughput of WLAN is decreased as increasing of number of AP.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.62-75
• /
• 2007

This paper describes a shaped-beam antenna for increasing the antenna gain of a radiating element. The proposed antenna structure is composed of an exciting element and a multi-layered disk array structure(MDAS). The stack micro-strip patch elements were used as the exciter for effectively radiating the electromagnetic power to the MDAS over the broadband, and finite metallic disk array elements - which give the role of a director for shaping the antenna beam with the high gain - were finitely and periodically layered onto it. The efficient power coupling between the exciter and the MDAS should be carried out in such a way that the proposed antenna has a high gain characteristic. The design parameters of the exciter and the MDAS should be optimized together to meet the required specifications to meet the required specifications. In this study, a shaped-beam antenna with high gain was optimally designed under the operating conditions with a linear polarization and the frequency band of $9.6{\sim}10.4\;GHz$. Two methods constructed using thin dielectric film and dielectric foam materials respectively were also proposed in order to implement the MBAS of the antenna. In particular, through the computer simulation process, the electrical performance variations of the antenna with the MDAS realized by the thin dielectric film materials were shown according to the number of disk array elements in the stack layer. Two kinds of antenna breadboard with the MDAS realized with the thin dielectric film and dielectric foam materials were fabricated, but experimentation was conducted only on the antenna breadboard(Type 1) with the MDAS realized with the thin dielectric film materials according to the number of disk array elements in the stack layer in order to compare it with the electrical performance variations obtained during the simulation. The measured antenna gain performance was found to be in good agreement with the simulated one, and showed the periodicity of the antenna gain variations according to the stack layer number of the disk array elements. The electrical performance of the Type 1 antenna was measured at the center frequency of 10 GHz. As the disk away elements became the ten stacks, a maximum antenna gain of 15.65 dBi was obtained, and the measured return loss was not less than 11.4 dB within the operating band. Therefore, a 5 dB gain improvement of the Type 1 antenna can be obtained by the MDAS that is excited by the stack microstrip patch elements. As the disk array elements became the twelve stacks, the antenna gain of the Type 1 was measured to be 1.35 dB more than the antenna gain of the Type 2 by the outer dielectric ring effect, and the 3 dB beam widths measured from the two antenna breadboards were about $28^{\circ}$ and $36^{\circ}$ respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.685-691
• /
• 2020

In this study, an algorithm that recognizes numbers from 0 to 9 was developed using the data obtained after tracking hand movements using the echo signal of a millimeter-wave radar sensor at 77 GHz. The echo signals obtained from the radar sensor by detecting the motion of a hand gesture revealed a cluster of irregular dots due to the difference in scattering cross-sectional area. A valid center point was obtained from them by applying a K-Means algorithm using 3D coordinate values. In addition, the obtained center points were connected to produce a numeric image. The recognition rate was compared by inputting the obtained image and an image similar to human handwriting by applying the smoothing technique to a CNN (Convolutional Neural Network) model trained with MNIST (Modified National Institute of Standards and Technology database). The experiment was conducted in two ways. First, in the recognition experiments using images with and without smoothing, average recognition rates of 77.0% and 81.0% were obtained, respectively. In the experiment of the CNN model with augmentation of learning data, a recognition rate of 97.5% and 99.0% on average was obtained in the recognition experiment using the image with and without smoothing technique, respectively. This study can be applied to various non-contact recognition technologies using radar sensors.