• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.49-55
• /
• 2005

In this paper, the phase locked harmonic oscillator(PLHO) using the analog PLL(Phase Locked Loop) is designed and implemented for a wireless LAN system. The harmonic oscillator is consisted of a ring resonator, a varactor diode and a PLL circuit. Because the fundamental fiequency of 8.5 GHz is used as the feedback signal for the PLL and the 2nd harmonic of 17.0 GHz is used as the output, a analog frequency divider for the phase comparison in the PLL system can be omitted. For the simple PLL circuit, the SPD(Sampling Phase Detector) as a phase comparator is used. The output power of the phase locked harmonic oscillator is 2.23 dBm at 17 GHz. The fundamental and 3rd harmonic suppressions are -31.5 dBc and -29.0 dBc, respectively. The measured phase noise characteristics are -87.6 dBc/Hz and -95.4 dBc/Hz at the of offset frequency of 1 kHz and 10 kHz from the carrier, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1702-1707
• /
• 2010

As quantities of the data that transmitting by the wireless are more increased, the interest and application are extending about 802.11n that uses by combination two existing 20MHz wireless LAN Channel. 802.11n use dual band of 2.4GHz band and 5.8GHz. So this is expected in mass wireless transmission method because of interference evasion effect in compliance with the radio communication of existing 2GHz neighborhood band. Like this 802.11n uses the radio as well and transmits information there is not only a possibility of undergoing an influence in radio wave environment of circumference. Specially the interior environment and outdoor environment is a possibility of saying that will be defined with each other different modeling as affects in radio communication is different. In this paper, we'll compare the influence to RF feature (802.11n) by (Indoor/Outdoor) environment difference through compared with 802.11n RF feature and Network feature in (Indoor/Outdoor) environment and also examine the correlation between RF feature and Network feature.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.830-838
• /
• 2003

In this paper, TX/RX dual operation microstrip single antenna for satellite communication is designed, analyzed, fabricated and measured. TX/RX frequency ranges are 14.0∼l4.5 GHz, 11.7∼12.75 GHz in respectively and vertical and horizontal polarizations are used for TX and RX. This antenna uses microstrip direct feeding for RX and aperture coupled strip-line feeding for TX and accommodates stacked elements for a high directivity and wide impedance bandwidth. In an analysis of single element, FDTD and MOM was compared and FDTD analysis was more accurate because of the consideration of finite structure and imperfect two ground planes. The proposed structure facilitates generally to an extension of two dimensional array and lower an unwanted radiation by strip-line feed in TX. TX/RX 8${\times}$4 array has a return loss below -10 dB, -14 dB in TX, RX respectively and a gain ranging from 19.1∼20.7 dB in TX, 21.2∼21.8 dB in RX which has a radiation efficiency of 43∼5l %, 52∼57 %.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.361-366
• /
• 2012

This paper proposes a low power capacitor cross-coupled 5.2 GHz band low noise amplifier(LNA) using the current-reused topology with the TSMC 0.18 ${\mu}m$ CMOS process. The proposed 5.2 GHz band LNA uses a capacitor cross-coupled $g_m$-boosting method for reducing current flow of circuit and a current-reused topology to decrease total power dissipation. The parallel LC networks are used to reduce size of spiral inductors. The simulation results show high gain of 17.4 dB and noise figure(NF) of 2.7 dB for 5.2 GHz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1003-1008
• /
• 2017

In this paper, we studied the design and fabrication of double T Structure with CPW antenna at around 5 GHz band.. To improve of frequency properties of antenna, Double T Structure with CPW antenna was simulated by HFSS(: High Frequency Structure Simulator). A double T Structure with CPW antenna was designed and fabricated by photolithograph on an FR4 substrate (dielectric constant of 4.4 and thickness of 1.6 mm). The fabricated A double T Structure with CPW antenna showed a center frequency, the minimum return loss and impedance were 5.29GHz, -34dB, and 390MHz, $49.6{\Omega}$ respectively.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1587_1588
• /
• 2009

In this paper, PCB embedded balanced-to-unbalamced duplexer using coupled LC resonator was introduced for low cost dualband WiMax front-end-module application. In order to obtain the function of bandpass filter and balun transformer, proposed duplexer was configured by using magnetically coupled LC resonator. Out-of-band suppression was enhanced by applying two m-Derived transform circuits to obtain transmission zeros at 2GHz and 4.8GHz. In order to reduce the size of embedded duplexer, BaSrTiO3 (BST) composite high Dk RCC film was applied to improve the capacitance density. This high Dk film provided the capacitance density of 12.2 pF/mm2. The simulation results shows that fabricated duplexer had an insertion loss of 2.9dB and 5.5dB and return loss of 15dB and 16dB for 2.5GHz~2.6GHz and 3.5GHz~3.6GHz, respectively. The maximum magnitude and phase imbalance were 0.01dB and 0.17dB, and 1degree and 2degree in its passband, respectively. The out-of-band suppression was observed approximately 29dB and 40dB below 1.9GHz and over 4.5GHz, respectively. It has a volume of 6 mm $\times$ 7 mm $\times$ 0.7 mm (height).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1455-1461
• /
• 2000

There are many researches to increase bandwidth of the microstrip patch antenna for wireless LAN. In spite of broad bandwidth, Bow-Tie antenna has disadvantages that are low gain and big size. In this paper, stacked Bow-Tie microstrip patch antenna for wireless LAN is designed in 5.725 ~5.825 GHz band. This antenna has characteristics that are broadband bandwidth, high gain and small size compared with microstrip patch antenna. In simulated results, the return loss is -34.2 dB at 5.78 GHz and bandwidth is 11.345% for VSWR 2:1 and 7.75%for VSWR 1.5:1. In measured results, the return loss is -38.45 dB at 5.78 GHz and bandwidth is 13% for VSWR 2:1 and 5.6% for VSWR 1.5:1. It has 73.16$^{\circ}$ -3dB beam width and 6.5dB gain.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.935-942
• /
• 2000

In this paper, miniature voltage-controlled oscillator(VCO) for 1.6GHz PCS band is designed and implemented. Colpitts type LC resonating oscillator is designed with multilayer PCB and circuit parameters are optimized using the circuit simulator. Using the optimized design parameters, miniature VCO with 6X6X1.8mm3 (0.065cc)dimensions is fabricated and experimented. Developed VCO has -1.67dBm $\pm$0.5dBm output power level in52.5MHz tunung range, and has -99.33dBc/Hz phase noise performance at 10 KHz frequency offset.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1096-1104
• /
• 2006

In this paper, the broadband antenna for the combined base station of Cellular/PCS/IMT-2000/Wibro and S-DMB services is designed and the proposed antenna allows having sufficient coverage for each service band. In order to get the broadband impedance matching, the tapered sections are applied on the both terminus of hi-conical respectively. The design parameter is calculated and simulated by using FDTD method. As a result, the measured bandwidth of the proposed antenna is $0.79GHz{\sim}2.93GHz$ and the gain is distributed from 5.5 dBi up to 8.19 dBi.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.3
• /
• pp.341-348
• /
• 2019

In this paper, a monopole type antenna applicable to WLAN and WiMAX standard frequency bands is designed and fabricated. The proposed antenna is designed to have rectangular ring and rectangular patch based on microstrip feeding for triple band characteristics and inserted two stub in the top of the rectangular ring patch to enhance impedance bandwidth characteristics. The proposed antenna has $18.0mm(2W_1+W_2){\times}33.0mm(L_7+L_8+L_9)$ on a dielectric substrate of $27.0mm(W_1){\times}44mm(L_1){\times}1.0mm$ size. From the fabrication and measurement results, impedance bandwidths of 660MHz (2,08 to 2.74GHz) for 2.4/2.5MHz band, 488MHz (3.40 to 3.88GHz) for 3.5MHz band, and 2,180MHz (4.61 to 6.79GHz) for 5,000MHz band were obtained based on the impedance bandwidth. The proposed antenna also obtained the measured gain and radiation pattern in the anechoic chamber.