• Journal of Power System Engineering
• /
• v.3 no.4
• /
• pp.51-56
• /
• 1999

The ultrasonic method, which is well known as nondestructive test method, is widely used to evaluate the material damage due to degradation. However, this method is just used for measuring the crack size and the thickness loss of the tube. The purpose of this study is to investigate the applicability of the ultrasonic technique for the evaluation of marine diesel engine exhaust valve and to suggest the correlations between the ultrasonic characteristics and valve degradation. From the evaluation of the results obtained, the technique of using the ultrasonic property was founds to be a efficient method to evaluate the degree of marine diesel engine exhaust valve by nondestructive test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.117-124
• /
• 2011

Valve springs with non-circular cross-section are widely used in automotive engines. Because of the reduced height, the oval cross-section provides some merits in its install height and stress distribution. This paper introduces a new method to generate optimal shape of the non-circular cross-section. For given width and height, arbitrary shape of the cross-section are described using the Hermite spline curves. Cross-section area and maximum stress level are chosen as performance indices, and nonlinear optimization problems are formulated with inequality constraints. Compared to a production spring wire, cross-section area can be reduced about 2.4 [%] without increasing maximum stress level. In addition, the other approach gives an optimum cross-section which reduces maximum stress level of 2.0 [%] without increasing cross-section area.

• Journal of ILASS-Korea
• /
• v.10 no.3
• /
• pp.45-53
• /
• 2005

The purpose of this study is to analyze that intake port swirl and fuel injection system have an effect on the engine performance in a turbocharged D.I. diesel engine of the displacement 9.4L. As result of steady flow test, when the valve eccentricity ratio moved to cylinder wall, the flow coefficient and swirl intensity is increased. And as the swirl is increased, the mean flow coefficient is decreased, whereas the Gulf factor is increased. Through this engine test, it can be expected to meet performance and emissions by the following applied parameters; the swirl ratio is 2.43, injection timing is BTDC 13oCA and compression is 15.5.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.4
• /
• pp.68-72
• /
• 2000

The ultrasonic method, which is well known as nondestructive test method, is widely used to evaluate the material damage due to degradation. However, this method is just used for measuring the crack size and the thickness loss of the tube. The purpose of this study is to investigate the application of the ultrasonic technique for the evaluation of marine diesel engine exhaust valve and to suggest the correlation between the ultrasonic characteristics and valve degradation. From the evaluation of the results obtained, the technique of using the ultrasonic property was founds to be a efficient method to degree of marine diesel engine exhaust valve by nondestructive test.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.735-741
• /
• 1986

An experimental study on the effects of exhaust pipe curvature on the performance of a diesel engine is presented. The experiments were carried out on a 4-cycle, 216 c.c diesel engine and two types of pipe curvature, circular arc and rectangle, were tested. The shaft output, shaft torque and specific fuel consumption were obtained by inserting bent pipes of different dimensions into the exhaust pipe at various engine operation conditions. It was found that the engine performance was decreased by the circular arc bent pipe and the effects were dominated by its arc angle. The decrease of engine performance was minimized by the arc angle of 180.deg.. By the rectangle pipes the performance was more decreased and the effects were little influenced by its dimensions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.4
• /
• pp.89-95
• /
• 2017

The improvement of a flow coefficient for the recirculation chill-down flow in a main oxidizer shut-off valve has been presented. The flow coefficient, which is mainly affected by the recirculation outlet port size and the configuration inside the valve, has been predicted with measured flow coefficient values. The comparison of experimentally measured flow coefficient with the predicted value shows the effect of valve inside configuration on the flow coefficient. Consequently, the flow coefficient is twice the previous value and about 75% of the pressure loss assigned to the main oxidizer shut-off valve can be used for additional pressure losses for other components in the recirculation chill-down system of a launch vehicle.

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.58-64
• /
• 2016

The main engine of a vehicle is used an common rail diesel engine for improving the efficiency of the whole load area. However, the generator engines is still used mechanical fuel injection valve drive cams. In addition, most of generator engines is applied a part-load operation of less than 50%. Therefore, diesel engine of vehicle set at 100% load is necessary to readjust in order to perform efficient operation because of part-load operation. In this study, the objective is to report the results of the part-load fuel consumption improvement by injection timing readjust to identify the operational characteristics of a generator engine currently operated in the facilities.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.219-224
• /
• 2005

In order to investigate transient behaviour of the CRW(Canard Rotor Wing) type UAV(Uninhabited Aerial Vehicle) propulsion system during flight mode transition considering flow control valve operation, the propulsion system was modelled using SIMULINK commercial program. For transient simulation of the main engine system, the ICV(Inter-Component Volume) method was applied. The valve system is to control the gas flow of the rotary duct system and the main duct system, and the analysis was performed with an assumption that the total gas mass flow of the main engine is the same as summation of the rotary duct flow and the main duct flow, and with consideration of valve loss, flow rate and effective area in valve angle variation. The performance analysis was carried out during flight mode transitions from the rotary flight mode to the fixed wing flight mode and vice versa mode at altitude of 1Km, flight Mach number 0.1 and maximum engine rpm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.1
• /
• pp.21-27
• /
• 2015

In order to meet the current emission regulations (EURO-6), it is necessary to significantly reduce $CH_4$ and $NO_X$ emissions. This study investigated the effect of a reduction in the valve overlap on the combustion and emission characteristics of a hydrogen-compressed natural gas engine under a part-load operating condition. The combustion and emission characteristics were analyzed for each fuel using the original camshaft and an altered camshaft with reduced valve overlap. The results showed that the thermal efficiency was decreased and the fuel flow was increased when using the altered camshaft. The $CO_2$ and $CH_4$ emissions were increased as a result of the reduced thermal efficiency. Under lean operating conditions, the $NO_X$ emission was decreased compared with one of the conventional camshaft. Thus, under the same fuels and operating conditions, it had a harmful influence on the emission characteristics and thermal efficiency.

• Journal of Energy Engineering
• /
• v.14 no.3 s.43
• /
• pp.180-186
• /
• 2005

As an engine has a wide range of RPM $(3000\~12000\;RPM)$, variable control system is necessary in order to increase engine performance. SCV has been frequently referred to as a possible way to increase engine performance at low RPM. The purpose of this study is to investigate on the influence of SCV, specially at the range of lower revolution, in a high-speed small engine. Experiments were conducted on 4 Valves SOHC/air-cooling single cylinder engine and SCV shapes have been tested fur swirl intensity, the performance of power, fuel consumption and emission. As a result, we find to use SCV range be below 5000 RPM which fuel consumption decreased $9\%$.