• 분석과학
• /
• 제9권3호
• /
• pp.1069-1075
• /
• 1996

• 한국정보과학회논문지:컴퓨팅의 실제 및 레터
• /
• 제8권3호
• /
• pp.318-327
• /
• 2002

본 논문에서는 MPEG-4 미세입자 계충 코딩 기법 등과 같은 망 상태 적응적인 계충적 스트리밍 코딩 기법에 적합한 새로운 스캔 방법을 소개한다. 제안된 스캔 방법은 사용자가 관심있는 영역의 영상정보 부호화를 최우선적으로 수행하여 전송하고 수신단에서도 해당 영상정보의 복호화을 최우선적으로 수행하도록 관리하여 복호된 비디오 영상의 주관적인 화질 향상을 보장하는 방법이다. 제안된 방법을 FGS 코딩 기법에 적용하면 특히 사용자가 관심 있는 영역의 주관적 화질을 약 1 dB ~ 3 dB정도 향상 시킬 수 있다.

• 대한공간정보학회지
• /
• 제24권2호
• /
• pp.71-78
• /
• 2016

After the 'Guidelines for the preservation of digital heritage' were published by UNESCO, interests in the fabrication of digital cultural heritage have been increasing throughout the world. The present study was intended to fabricate digital cultural heritages for existing cultural properties using the reverse engineering technology and obtain two-dimensional drawings. Jinju Castle Gongbukmun, which is a cultural property, was selected as a study subject and 3D modeling of Jinju Castle Gongbukmun was conducted by implementing 3D scanning and processing the point cloud data. Using the Gongbukmun 3D model (3D-Gongbukmun) made as such, requirements as a digital heritage were reviewed and 2D drawings of Gongbukmun such as front views, ground plans, and side views could be prepared.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.201-206
• /
• 2004

Laser scanner are getting used for inspection and reverse engineering in industry such as motors, electronic products, dies and molds. However, due to the lack of efficient scanning technique, the tasks become limited to the low accuracy purpose. The main reasons for this limitation for usefulness are caused from the optical drawback, such as irregular reflection, scanning direction normal to measuring surface, the influence of surface integrity, and other optical disturbances. To overcome these drawback of laser scanner, this study propose the mechanism to reduce the optical trouble by using the 2 kinds of rotational movement axis and by composing the spherical coordinate to scanning the surface keeping normal direction consistently. So, it could be designed and interfaced the measuring device to realize that mechanism, and then it could acquisite the accurate 3D form cloud data. Also, these data are compared with the standard master ball and the data acquisited from the touch point sensor, to evaluate the accuracy and stability of measurement and to demonstrate the implementation of an dental tooth purpose system

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.177-178
• /
• 2014

This work proposes a two-dimensional (2-D) laser scanning mirror actuator with a simple structure composed of one magnet and four coils. The mirror-actuating device generates 2-D scanning motions about two orthogonal axes by combining electromagnetic actuators of the conventional moving-magnet types. The magnet is attached to back side of the mirror placed inside of the moving frame. The four coils is placed on the base frame in a cross shape. We implement a finite element analysis to calculate magnetic flux in the electromagnetic system with the overall size of $20mm(W){\times}20mm(D){\times}13mm(H)$ for the mirror size of $8mm{\times}8mm$. The each moving-magnet type electromagnetic actuator has the motor constant 3.41 mNm/A and the restoring constant 1.75 mNm/rad and the resonance frequency of 58 Hz and the bandwidth of 80 Hz. The proposed compact and simple 2-D scanning mirror predicted advantages of large 2-D angular deflections, wide frequency bandwidth and low manufacturing cost.

• 박물관보존과학
• /
• 제22권
• /
• pp.15-26
• /
• 2019

이 연구에서는 표면형상 취득에 최적화되어 있는 광학식 정밀스캐닝과 내부 형상획득에 사용되는 X-선 CT스캐닝 결과를 이용하여 삼총통의 내·외부 형상을 다각적으로 분석할 수 있는 3차원(이하 3D) 융합 모델을 제작하였다. 먼저 두 스캐닝 결과를 호환 가능한 확장자로 변환 한 다음 상호간의 정합성을 검증하고자 3D 편차분석을 수행하였다. 이 결과, 두 스캐닝 모델은 대부분(56.98%) ±0.1mm 이내의 편차를 보였으며, 이 수치는 ICP 알고리즘 기반의 정합 및 병합에 큰 영향을 주지 않았다. 병합된 데이터는 총통의 외부 표면색 및 미세형상, 내부 두께 및 구조를 잘 표현하였다. 광학식 표면스캐닝과 X-선 CT스캐닝의 3D 융합 모델은 문화유산의 디지털기록화뿐만 아니라 제작기법 해석에 유용하게 사용되었다. 향후 박물관 전시 영역에서 전시품의 과학적 조사 정보를 보다 쉽게 관람객에게 전달하는 효과를 발휘 할 것으로 기대된다.

• 제어로봇시스템학회논문지
• /
• 제21권12호
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• Applied Microscopy
• /
• 제42권3호
• /
• pp.158-163
• /
• 2012

Detailed comparison of low-voltage scanning electron microscopy and electron holography techniques for two-dimensional (2D) dopant profiling was carried out with using the same multilayered p-n junction specimen. The dopant profiles obtained from two methods are in good agreement with each other. It demonstrates that reliability of dopant profile measurement can be increased through precise comparison of 2D profiles obtained from various microscopic techniques.

• Journal of Chest Surgery
• /
• 제53권5호
• /
• pp.301-305
• /
• 2020

Background: Radiographic modalities have been commonly used to evaluate pectus carinatum (PC), and compressive orthotic bracing is the most widely accepted treatment method. The aim of this study was to determine the efficacy of 3-dimensional (3D) body surface scanning as an alternative modality for the evaluation of PC. Methods: The medical records of 63 patients with PC who were treated with compressive orthotic bracing therapy between July 2017 and February 2019 were retrospectively analyzed. Using both 2-view chest radiography (posteroanterior and lateral view) and 3D body scanning, the height of maximal protrusion of the chest wall was measured both before and after 2 weeks of bracing therapy. The difference between the pre- and post-treatment measurements was calculated for both modalities, and these differences were compared and analyzed. Results: Based on the comparison between the pre- and post-treatment radiographs, bracing therapy produced favorable outcomes in all patients (p<0.001). The measurements obtained via 3D scanning were strongly correlated with those obtained via chest radiography (r=0.60). Conclusion: Based on the findings of this study, 3D body surface scanning appears to be an effective, radiation-free, and simple method for the post-treatment follow-up evaluation of PC, and thus can be considered an alternative to radiography.

• Journal of Computational Design and Engineering
• /
• 제2권2호
• /
• pp.96-104
• /
• 2015

Aluminum die casting is an important manufacturing process for mechanical components. Die casting is known to be more accurate than other types of casting; however, post-machining is usually necessary to achieve the required accuracy. The goal of this investigation is to develop machining- free aluminum die casting. Improvement of the accuracy of planar and cylindrical parts is expected by correcting metal molds. In the proposed method, the shape of cast aluminum made with the initial metal molds is measured by 3D scanning. The 3D scan data includes information about deformations that occur during casting. Therefore, it is possible to estimate the deformation and correction amounts by comparing 3D scan data with product computer-aided design (CAD) data. We corrected planar and cylindrical parts of the CAD data for the mold. In addition, we corrected the planar part of the metal mold using the corrected mold data. The effectiveness of the proposed method is demonstrated by evaluating the accuracy improvement of the cast aluminum made with the corrected mold.