• Korean Journal of Construction Engineering and Management
• /
• v.10 no.1
• /
• pp.136-145
• /
• 2009

The objective of the Intelligent Excavation System (IES) is to recognize the work environment and produce work plan and automatically control the excavator through integrating sensor and robot technologies. This paper discusses one of the core technologies of IES development project, development of 3D work environment modeling. 3D laser scanner is used for 3-dimensional mathematical model that can be visualized in virtual space in 3D. This paper describes (1) how the most appropriate 3D imaging system has been chosen; (2) the development of user interface and customization of the s/w to control the scanner for IES project; (3) the development of the mobile station for the scanner; (4) and the algorithm for the automatic registration of laser scan segments for IES project. The development system has been tested on the construction field and lessons learned and future development requirements are suggested.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.1 s.149
• /
• pp.157-166
• /
• 2006

The human body, which is composed of concave and convex curvatures, makes it difficult to transfer into 2D patterns directly from 3D data. In previous studies. Jeong, et al.(2004) suggested the block method was fester and easier when dealing with the triangular patches of male's upper dress form. Although the block method is useful to make a pattern, the information(area, length, etc.) from a 2D pattern would be different depending on the direction of the block method. As a result horizontal and diagonal block methods were suggested as optimal methods for 2D tight-fitting patterns. These block methods were closer to the original area of the 3D scan data than the vertical block method. The total area of the 2D pattern obtained by the horizontal and diagonal block methods showed little differences. In case of the horizontal and diagonal block methods, the total error of the 2D pattern area ranged from $0.01\%\~0.25\%$. In comparing the length of the 2D pattern with that of the 3D scan data, the obtained 2D pattern was $0.1\~0.2cm$ shorter than the 3D scan data, which was within the acceptable range of errors in making clothes. 3D space distribution images between the body surface and the experimental clothing were also measured and $3\%$ enlargement of the original pattern was verified as the adequate adjustment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.188-189
• /
• 2022

With the development of nano-reinforcement technology, TiO₂ nanomaterials have received widespread attention as one of the additives without pozzolanic reaction, which can be used to improve the mechanical properties of cement-based materials. Meanwhile, with the development of additive manufacturing technology or known as 3D printing technology, its application in the construction field has also got noticed. Therefore, in this work, the effect of three sizes of TiO₂ on the compressive strength of hardened cement-based materials fabricated by binder jetting 3d printing was evaluated. According to the results, the TiO₂ particles with larger sizes can provide better reinforcement to the hardened cement due to its more significant filling effect.

• Korean Journal of Computational Design and Engineering
• /
• v.10 no.2
• /
• pp.77-88
• /
• 2005

This paper introduces a project for the development of an F-125 machine using 3D PLM systems including 3D CAD, CAM, CAE, PDM, and DMU systems. Here, the F-125 machine is a formula racing car equipped with a 125cc motorcycle engine. A development process and computer-integrated environment was established using 3D PLM systems on the conceptual basis of concurrent and virtual engineering. A DMU model for a full vehicle was built using CATIA V.5 and used to check interference between parts and to simulate assembly process. This DMU-based approach enables to find and fix manufacturing problems in the early design stage. All development activities have been done by the graduate and undergraduate students of the automotive engineering department of Kookmin University. Through the project, the students could acquire knowledge about car development process and 3D PLM systems in automotive industry.

• Journal of Embryo Transfer
• /
• v.31 no.3
• /
• pp.169-177
• /
• 2016

There is a growing interest in the application of primary hepatocytes for treatment of liver diseases in humans and for drug development. Several studies have focused on long-term survival and di-differentiation blocking of primary hepatocytes in an in vitro culture system. Therefore, the present study also aimed to optimize an in vitro culture system using primary rat hepatocytes. Primary rat hepatocytes from 6-week-old male Crl:CD rats were isolated using a modified two-step collagenase perfusion. Healthy $3.5{\times}10^6$ primary rat hepatocytes were seeded into a 2 dimensional (2D) culture in a 25T culture flask coated with collagen type I or into a 3D culture in a 125-ml spinner flask for 7 days. Production of plasma protein (ALB and TF), apoptosis (BAX and BCL2), and CYP (CYP3A1) related genes were compared between the 2D and 3D culture systems. The 3D culture system had an advantage over the 2D system because of the relatively high expression of ALB and low expression of BAX in the 3D system. However, the level of CYP3A1 did not improve in the 3D culture with and without the presence of a dexamethasone inducer. Therefore, 3D culture has an advantage for albumin production and primary rat hepatocyte survivability, but a low expression of CYP3A1 indicated that primary rat hepatocytes require a high-density culture for stress reduction by continuous flow.

• Animal cells and systems
• /
• v.3 no.4
• /
• pp.369-374
• /
• 1999

The life history and development of Tetrastichus sp. parasitizing fallwebworm pupa in Korea were studied. The mean lifetime fecundity was 94.7 with a maximum of 125, and the portion of female progeny averaged 90.3%. A male and a female lived for an average of 19.8${\pm}$4.5 and 21.7${\pm}$4.2 days, respectively. The duration of development for each stage was as follows: egg, 2 d; the 1st instar larva, 2${\pm}$1 d; the 2nd instar larva, 2${\pm}$1 d: the 3rd instar larva, 3${\pm}$1 d; the 4th instar larva, 6${\pm}$2 d; and pupa, 8${\pm}$2 d. Total developmental duration from hatching of the larva to adult emergence required 21.1${\pm}$3.7 d, and females took 1-2 days more than males in the incubator (28$^{\circ}C$, 70% RH, and 16:8 LD).

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.3
• /
• pp.71-81
• /
• 2010

In 1994, Korean construction research and development (R&D) projects received investments amounting to 1.2 billion KRW, an amount that rose to 164.8 billion KRW in 2007. Under the current system, construction researchers submit the application records of Construction Research and Development (R&D) in construction projects to the Korea Institute of Construction & Transportation Technology Evaluation and Planning. The performance of Construction R&D projects has thus been dependent on the subjective reporting of the results by the researchers themselves. For this reason, it is difficult to secure confidence in the records of Construction Research and Development. Therefore, this research suggested measures for revitalizing Construction Research and Development, analyzed approaches to cost-saving in Construction Research and Development, and analyzed economic effectiveness in the results of construction R&D.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.3
• /
• pp.468-486
• /
• 2017

In this study, three kinds of wearable fashion prototypes were developed using 3D printers with the goal of developing a practical production method for daily clothes. Prototypes were modeled using Rhinoceros software and developed using FDM 3D printers and TPU filaments. The results of this study are as follows. First, it confirmed the possibility of FDM-type entry-level 3D printers as a tool to develop wearable fashion products. Second, TPU filaments that are soft and ductile are highly likely to be used as a clothing material. Third, patterns designed through the 3D modeling process can be sampled directly to a 3D printer and easily corrected and supplemented. Fourth, it was confirmed that TPU prints of about 1.00mm thickness can be sewn with fabric using sewing machines through the development of 'Prototype 1' and 'Prototype 2'; in addition, hand stitching is also possible. Fifth, as in the case of 'Prototype 3', it is possible to fabricate a garment fit enough to the body if the clothing configuration is designed to connect the basic module using TPU filaments. In the future, the development of wearable fashion prototypes using various materials and 3D printing technology will help diversify everyday clothes.

• Journal of Digital Convergence
• /
• v.14 no.3
• /
• pp.329-335
• /
• 2016

This paper's objective is to investigate the display fatigue quantitatively according to watching 2D and 3D videos on the display. Though it has been known commonly that display fatigue by 3D is greater than one by 2D, there have been few researches with an aim to measure display fatigue scientifically. Flicker fusion frequency and cybersickness degree were measured before/after sixteen subjects(Male 8, Female 8) watch the 2D, 3D images. Two dependent variables affected by 2D and 3D videos were analyzed and compared statistically based on scientific evidences and researches. 3D showed a value 4 times as much as 2D in cybersickness increase rate, and the reduction rate of 3D was 2 times as much as that of 2D.

• The Journal of the Korea Contents Association
• /
• v.7 no.7
• /
• pp.87-95
• /
• 2007

On this study, we researched differences between 2D and 3D with principle of GUI with the estimate that the user interface will be changed to 3D and we figured out the special feature of 3d-GUI through 3 ways, Autonomy, Interaction and Presence. Based on this theory research, we also had a survey with difference of 3d and 2d GUI to forecast the possibility of 3d-GUI for the main user interface of the future media contents and finally found out its marketability as an ideal interface.