• Fashion & Textile Research Journal
• /
• v.10 no.5
• /
• pp.713-720
• /
• 2008

The purpose of this study was to propose the method reproducing three dimensional figure data to a reconstructed body by the styrofoam board. To make the reconstructed body, the 3D figure data were rotated to make symmetry and the surfaces were edited. The horizontal curves were gathered equally-spaced based on the waist horizontal plane. we proposed the process to cut the styrofoam board according to the horizontal curves, to assemble them to organize the shape of the body figure and to coat the surface with the knitted. The 3-dimensional figure data of straight type, swayback type, lean-back type and bend-forward type were selected and the reconstructed bodies were made as above. And the compatibility was verified by the measurement comparison and deviations between 3-dimensional figure data and reconstructed body.

• Journal of Sasang Constitutional Medicine
• /
• v.19 no.3
• /
• pp.51-61
• /
• 2007

1. Objectives The Face is an important standard for the classification of Sasang Constitutions. We are developing 3D Automatic Face Recognition Apparatus(3D-AFRA) to analyse the facial characteristics. This apparatus show us 3D image and data of man's face and measure facial figure data. So We should examine the Measurement of Facial Figure data error of 3D Automatic Face Recognition Apparatus(3D-AFRA) in Software Error Analysis. 2. Methods We scanned face status by using 3D Automatic Face Recognition Apparatus(3D-AFRA). And we measured lengths Between Facial Definition Parameters of facial figure data by Facial Measurement program. 2.1 Repeatability test We measured lengths Between Facial Definition Parameters of facial figure data restored by 3D-AFRA by Facial Measurement program 10 times. Then we compared 10 results each other for repeatability test. 2.2 Measurement error test We measured lengths Between Facial Definition Parameters of facial figure data by two different measurement program that are Facial Measurement program and Rapidform2006. At measuring lengths Between Facial Definition Parameters, we uses two measurement way. The one is straight line measurement, the other is curved line measurement. Then we compared results measured by Facial Measurement program with results measured by Rapidform2006. 3. Results and Conclusions In repeatability test, standard deviation of results is 0.084-0.450mm. And in straight line measurement error test, the average error 0.0582mm, and the maximum error was 0.28mm. In curved line measurement error test, the average error 0.413mm, and the maximum error was 1.53mm. In conclusion, we assessed that the accuracy and repeatability of Facial Measurement program is considerably good. From now on we complement accuracy of 3D-AFRA in Hardware and Software.

• Journal of Digital Convergence
• /
• v.12 no.9
• /
• pp.335-341
• /
• 2014

Due to the expiration of the 3D printer's patent, the articles covering the market activation and bright prospects for the future industry are being released. What are the requirements for the 3D printer to become popular like a general printer? To get the answer, on-line survey was performed for the activation of 3D printer. As a result, tit is observed that he public prefers creative printer and figure, and prefers to use through pay or free download rather than designing digital blueprint, which is output data. For the activation and popularization of 3D printer, figure is familiar to the public who are frequently exposed to image media contents, and it also has motivation factor to use and purchase 3D printer. For distribution of digital blueprint of figure content, the preparation of related law and regulation and activation of online market would be of help for activation of 3D printer.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.10
• /
• pp.796-800
• /
• 2009

Currently, there are many software tools that can generate 3D human figure models and animations based on the advancement of computer graphics technology. However, we still have problems in interoperability of human data models in different applications because common data models do not exist. To address this issue, the Web3D Consortium and the ISO/IEC JTC1 SC24 WG6 have developed the H-Anim standard. However, H-Anim does not include human motion data formats although it defines the structure of a human figure. This research is intended to obtain interoperable human animation by defining the data for human motions in H- Anim figures. In this paper, we describe a syntactic method to define motion data for the H-Anim figure and its implementation. In addition, we describe a method of specifying motion parameters necessary for generating animations by using an arbitrary character model data set created by a general graphics tool.

• Journal of Sasang Constitutional Medicine
• /
• v.19 no.2
• /
• pp.30-39
• /
• 2007

1. Objectives The Face is an important standard for the classification of Sasang Constitution. We are developing 3D Automatic Face Recognition Apparatus(3D-AFRA) to analyse the facial characteristics. This apparatus show us 3D image and data of man's face and measure facial figure data. So we should examine the figure restoration error of 3D Automatic Fare Recognition Apparatus(3D-AFRA) in hardware Error Analysis. 2. Methods We scanned Face status by using 3D Automatic Face Recognition Apparatus(3D-AFRA). And also we scanned Face status by using laser scanner(vivid 9i). We compared facial shape data be restored by 3D Automatic Face Recognition Apparatus(3D-AFRA) with facial shape data that be restorated by 3D laser scanner. And we analysed the average error and the maximum error of two data. 3. Results and Conclusions In frontal face, the average error was 0.48mm. and the maximum error was 4.60mm. In whole face, the average error of was 0.99mm. And the maximum error was 6.64mm. In conclusion, We assessed that accuracy of 3D Automatic Face Recognition Apparatus(3D-AFRA) is considerably good.

• ETRI Journal
• /
• v.24 no.3
• /
• pp.190-196
• /
• 2002

This paper presents millimeter wave monolithic microwave integrated circuit (MMIC) low noise amplifiers using a $0.15{\mu}m$ commercial pHEMT process. After carefully investigating design considerations for millimeter-wave applications, with emphasis on the active device model and electomagnetic (EM) simulation, we designed two single-ended low noise amplifiers, one for Q-band and one for V-band. The Q-band two stage amplifier showed an average noise figure of 2.2 dB with an 18.3 dB average gain at 44 GHz. The V-band two stage amplifier showed an average noise figure of 2.9 dB with a 14.7 dB average gain at 65 GHz. Our design technique and model demonstrates good agreement between measured and predicted results. Compared with the published data, this work also presents state-of-the-art performance in terms of the gain and noise figure.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1092-1094
• /
• 2009

The purpose of the research was to figure out the optimal binocular parallax inducing the least 3D visual fatigue. Subjective 3D visual fatigue was measured while the revolution depth and the average depth of an object were manipulated. The optimal binocular parallax was figured out by using data fitting method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.7
• /
• pp.1109-1120
• /
• 2009

This study develops a fitted torso type basic pattern for men by utilizing 3D body scan data. Recent fashion trends are reflected in the development of the pattern. The subjects were 15 men in their 20's, who wear size 95 (M size). Body scan data was obtained through a 3D whole body scanner (WB4, Cyberware, USA), and a body surface development figure for developing male fitted torso type basic pattern was attained through the use of Rapid Form 2006 as well as Auto CAD 2006 programs. The results are as follows: A body surface development figure through body surface segment method showed high exactitude in an error range of 100$\pm$1%. In addition, it occurred in an error range of 100:1:3% because of the hard scanning conditions in the incline of the shoulder and armpit areas. However, the body surface development figure as well as the direct measurement results can be used as basic data for the given patternmaking since the error range falls into 100$\pm$3%. Dart amounts obtained from the average cross section were center back 2.2cm (24.3%), back armpit point 3.8cm (41.8%), front armpit point 3.0cm (33.9%). As shown the jacket pattern, the biggest dart amount was portioned out at the back armpit point. The drafting equations for the development pattern acquired are as follows; Full width=C/2+5cm, back length=height/4-1cm, armhole depth=(C/10+12cm)+3cm, back width=2C/10+2cm, front width=2C/10. The development pattern was a fitted torso basic pattern that was composed of 3 pieces, so it would be very useful in developing shirt or jacket patterns. According to the results of the evaluation of the developed pattern appearance, it obtained higher scores of over 3.5 points in almost items, meaning that the developed pattern is appropriate for a male fitted torso type basic pattern. It suggests a possibility of patternmaking from a body surface development figure in 2-D to prototype.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.7-13
• /
• 1997

A X-band 3-stage monolithic LNA (low noise amplifier) with series feedback has been successfully desined and demonstrated by suign 0.5-$\mu\textrm{m}$ GaAs MESFET. In the design of the 3-stage LNA, the effects of series feedback to the noise figure, the gain, and the stability have been investigated ot find the optimal short stub length. As a result, the inductive series feedback topology which has 10degree short stub in the GaAs MESFET source lead, has been employed in the 1-st stage. The fabricated MMIC LNA's chip size is only 1mm$^{2}$/stage, which is smaller than the previously reported X-band MMIC input/output return losses are less than -10dB and -15dB, respectively. The noise figure (NF) is less than 2.6dB. The measured data show good agreement with the simulated values.

• Fashion & Textile Research Journal
• /
• v.8 no.2
• /
• pp.209-213
• /
• 2006

The 3-D information is useful as basic data which has been utilized in the development of simulating technology as fit-simulation. The experiment is designed to take some useful data on the variant shapes which contribute in simulating the adaptability of the clothes. The general figure of the clothes are made after the figure of the basic standing posture of the human body. The shape of the clothes fits with kinetic characteristic of the human body as the form of the clothes gets twisted, the ease of the clothes changes, and the clothes itself expands. We studied the dressed shapes of blouse according to two types of the arm movement(basic posture and reach forward) and three types of clothes(foundation, blouse with short sleeves and sleeveless) in the sit-down-posture. We accomplished some experimental data on three-dimensional measurement of the dressing shapes using TDS-3100 3-D scanner made in Japan PULSTECH. It is considered that the variant of shapes and distribution of gaps in the dressed shapes of blouse are determined by the adaptability of clothes made in arm movement.