• 문화기술의 융합
• /
• 제9권3호
• /
• pp.633-640
• /
• 2023

본 연구는 운행선 경전철 직결식 궤도 부설구간에서 발생한 도상블록의 변위거동 특성을 분석하여 적정 보강 방안을 도출하고자 현장조사를 바탕으로 한 수치해석을 수행하였다. 본 연구의 대상선로는 교량상 급곡선 직결식 콘크리트 궤도로서 교량바닥판에 부설된 도상블록이 종방향 및 횡방향으로 이동하는 문제가 발생하여 이에 대한 메커니즘을 분석하였다. 본 연구에서는 3D Solid요소를 이용한 궤도구조 모델링을 바탕으로 운행하중 조건에서 발생가능한 직결식 궤도의 거동을 분석하고 다양한 보강방안에 대한 보강효과를 해석적으로 분석하였다. 도상블럭의 보강 전, 후 횡변위 분석결과, 극한 횡압 작용 시 보강 후 최대 횡변위는 보강 전 대비 약 3% 수준(약 0.1mm)으로 크게 감소하는 것으로 분석되었다. 또한 채움 모르타르, 교량 바닥판, 보강철근의 발생응력 검토결과, 모두 2.6 이상의 충분한 안전율을 확보하는 것으로 분석되어 보강방안에 대한 최적 조건을 도출하였다. 따라서 본 연구에서 검토한 앵커링 보강 수량 및 대칭형 앵커배치는 도상블록 횡방향 변위 발생 제어 및 교량, 도상블록의 구조적 건전성 확보에 효과적일것으로 판단된다.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1617-1630
• /
• 2018

The crucial differences between conventional rail with split-type connectors and continuous welded rails are axial stress in the longitudinal direction and stability, as well as other issues generated under the influence of loading effects. Longitudinal stresses generated in continuously welded rails on railway bridges are strongly influenced by the nonlinear behavior of the supporting system comprising sleepers and ballasts. Thus, the track structure interaction cannot be neglected. The rail-support system mentioned above has properties of non-uniform material distribution and uncertainty of construction quality. The linear elastic hypothesis therefore cannot correctly evaluate the stress distribution within the rails. The aim of this study is to apply the nonlinear finite element method using the nonlinear coupling interface between the track and structural model and to illustrate the welded rail behavior under the loading effect and uncertain factors of the ballast. Numerical results of nonlinear finite analysis with a three-dimensional solid and frame element model are presented for a typical track-bridge system. A composite plate girder, modeled by solid and shell elements, is also analyzed to consider the behavior of the welded rail. The analysis result showed buckling under the independent calculations of load cases, including 'temperature change', 'bending of the supporting structure', and 'braking' of the railway vehicle. A parametric study of the load combination method and the loading sequence is also included in this analysis.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제38권6호
• /
• pp.332-336
• /
• 2012

Objectives: This study sought to evaluate fixation methods and determine the best method for the postoperative stabilization of maxillary osteotomy. For our analysis we performed a three-dimensional finite element analysis of stress distribution on the plate, screw, and surrounding bone, as well as displacement onto the plate. Materials and Methods: We generated a model using synthetic skull scan data; an initital surface model was changed to a solid model using software. Modified anterior segmental osteotomy (using Park's method) was made using the program, and four different types of fixation methods were used. An anterior load of 100 N was applied on the palatal surface of two central incisors. Results: The Type 1 (L-shaped) fixation method gave stresses of 187.8 MPa at the plate, 45.8 MPa at the screw, and 15.4 MPa at the bone around the plate. The Type 2 (I-shaped) fixation method gave stresses of 186.6 MPa at the plate, 75.7 MPa at the screw, and 13.8 MPa at the bone around the plate. The Type 3 (inverted L-shaped) fixation method gave stresses of 28.6 MPa at the plate, 29.9 MPa at the screw, and 15.3 MPa at the bone around the plate. The Type 4 (I-shaped) fixation method gave stresses of 34.8 MPa at the plate, 36.9 MPa at the screw, and 14.9 MPa at the bone around the plate. The deflection of the plates for the four fixation methods was 0.014 mm, 0.022 mm, 0.017 mm, and 0.018 mm, respectively. Conclusion: The Type 3 (inverted L-shaped) fixation method offers more stability than the other fixation methods. We therefore recommend this method for the postoperative stabilization of maxillary osteotomy.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.310-317
• /
• 2013

In this paper, the contact pressure of the wafer and polishing pad for final polishing process for 300 mm-wafer were investigated through numerical analysis using FEM tool, ANSYS. The distribution of the contact pressure is one of main parameters which affects on the flatness and surface roughness of polished wafers. Two types of polishing head, a hard type head with ceramic disk and a soft type head with air bag were considered. The effects of the deformation and initial shape of table on the contact pressure were also examined. Both heads and tables were modeled as 3D finite element model from solid model, and the material properties of polishing pads and rubber plate for the air-bag head were obtained from tensile tests. The contact pressure deviation on wafer surface was smaller with air bag head than hard type head even when the table had form errors such as convex or concave. From this 3D analysis, it could be concluded that the air-bag head has better uniformity of the contact pressure on wafer. Also, the effects of inner diameter of air bag and radial clearance between wafer and retainer were investigated as view point of contact pressure concentration on the edge of wafer.

• 한국재난정보학회 논문집
• /
• 제9권2호
• /
• pp.206-213
• /
• 2013

본 연구에서는 현재 일본에서 개발되어 적용되고 있는 고형화 에폭시 수지를 이용한 아스팔트 혼합물의 국내 강상판 적용성을 평가 하고자 하였다. 다양한 문헌조사를 통한 고형화 에폭시 아스팔트 혼합물의 특성을 파악한 후, 배합설계 와 혼합물 평가를 실시하였다. 그 결과 강상판에 적용되는 다른 재래식 혼합물에 비하여 성능이 월등함을 알 수 있었다. 또한, 3D 유한 요소 해석을 수행한 결과 에폭시 아스팔트가 시공 시 충분한 공용성능을 보이는 것으로 판단되어 국내에서 일반적으로 사용되고 있는 배치식 플랜트 통해 고형화 에폭시 아스팔트 혼합물 생산 후 시험시공을 실시하였다. 시공 후 공용성을 평가하기 위해 BPT 실험을 한 결과 포장의 표면은 기준이상의 마찰력을 나타내는 것을 알 수 있었다.

• 한국기계가공학회지
• /
• 제14권6호
• /
• pp.35-40
• /
• 2015

An IP-2 type container is used for the transport of low-level radioactive materials. An IP-2 type metal container was modeled and analyzed for the dropping conditions in normal transport conditions required by NSSC Notice 2014-50, "Regulations on the packaging and transport of radioactive materials." Structural analyses were performed by finite element method, and the acceptability was reviewed by comparing the results with technical standards and maximum allowable stresses of each material. Structural members of the container were modeled as 3D solid elements, and the possible dropping directions were considered in these analyses. Results show that maximum stresses, maximum deformed gaps in the cover, and maximum estimated thickness reduction in structural members were well below the allowable limits; thus, the structural integrity of the container was confirmed.

• Steel and Composite Structures
• /
• 제28권6호
• /
• pp.767-778
• /
• 2018

The purpose of this study is to investigate how a fully restrained bolted beam splice affects the connection behavior as a column-tree connection in steel special moment frames under cyclic loading when located within the plastic hinge zone. The impacts of this attachment in protected zone are observed by using nonlinear finite element analyses. This type of splice connection is designed as slip-critical connection and thereby, the possible effects of slippage of the bolts due to a possible loss of pretension in the bolts are also investigated. The 3D models with solid elements that have been developed includes three types of connections which are the connection having fully restrained beam splice located in the plastic hinge location, the connection having fully restrained beam splice located out of the plastic hinge and the connection without beam splice. All connection models satisfied the requirement for the special moment frame connections providing sufficient flexural resistance, determined at column face stated in AISC 341-16. In the connection model having fully restrained beam splice located in the plastic hinge, due to the pretension loss in the bolts, the friction force on the contact surfaces is exceeded, resulting in a relative slip. The reduction in the energy dissipation capacity of the connection is observed to be insignificant. The possibility of the crack occurrence around the bolt holes closest to the column face is found to be higher for the splice connection within the protected zone.

• Structural Engineering and Mechanics
• /
• 제64권5호
• /
• pp.653-660
• /
• 2017

The aim of this study is to accurately estimate seismic damage and the collapse mechanism of the historical stone masonry minaret "Hafsa Sultan", which was built in 1522. Surveying measurements and material tests were conducted to obtain a 3D solid model and the mechanical properties of the components of the minaret. The initial Finite Element (FE) model is analyzed and numerical dynamic characteristics of the minaret are obtained. The Operational Modal Analysis (OMA) method is conducted to obtain the experimental dynamic characteristics of the minaret and the initial FE model is calibrated by using the experimental results. Then, linear time history (LTH) and nonlinear time history (NLTH) analyses are carried out on the calibrated FE model by using two different ground motions. Iron clamps which used as connection element between the stones of the minaret considerably increase the tensile strength of the masonry system. The Concrete Damage Plasticity (CDP) model is selected in the nonlinear analyses in ABAQUS. The analyses conducted indicate that the results of the linear analyses are not as realistic as the nonlinear analysis results when compared with existing damage.

• Journal of Welding and Joining
• /
• 제29권5호
• /
• pp.63-71
• /
• 2011

Three-dimensional finite element analysis is performed to study the temperature distribution phenomenon of TIG assisted friction stir welding (TAFSW) between dissimilar plates (Al 6061-T6 and stainless steel 304). TAFSW is a solid-state welding process that integrates TIG (Tungsten Inert Gas) into a friction stir welding (FSW), to preheat the harder material ahead of FSW tool during welding. In order to facilitate the industrial application of welding, 3D numerical modeling of heat transfer has been carried out applying Finite Element Method (FEM). The temperature distribution due to heat generation during TAFSW on dissimilar materials joint is analysed using in-house solver. Moving heat source along with frictional heat between the work specimens and tool surface is considered to calculate the heat input. The analytical model used predicts successfully the maximum welding temperatures that occur on the dissimilar materials during TAFSW. Comparison with the infra red camera and thermocouple measurement results shows that the results from the current numerical simulation have good agreement with the measured data.

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.1105-1111
• /
• 2010

한국원자력연구원은 전력생산과 해수담수화를 동시에 수행하고 친환경적인 SMART 원자로를 개발하였다. SMART 원자로의 여러 구조물 중에 제어봉 구동 장치(CRDM)는 제어봉의 삽입 량을 조절하여 원자로의 출력을 조정하고 비상시 제어봉을 긴급 삽입하여 원자로를 정지시키기 위한 기기이다. 본 연구의 목적은 제어봉 구동 장치의 구조적 건전성을 확보하기 위해서 동특성해석을 수행하는 것이다. 또한 향후 내진해석에 활용될 단순모델의 활용을 위해 상세모델과의 비교, 검증을 수행하였다. 해석은 유한요소 해석기법을 활용하였고 상용해석 프로그램인 ABAQUS 와 ANSYS V12 를 사용하였다. 유한요소 해석모델은 상세모델인 3-D Solid 모델과 단순모델인 Beam 모델을 작성하여 비교하였고 추가로 단순모델을 오일러 보인 Beam4 요소와 티모센코 보인 Beam188 요소로 작성하여 비교 검토하였다. 향후 SMART 원자로집합체의 단순모델을 작성하여 내진해석 등 다양한 해석에 활용될 계획이므로 단순모델은 상세모델과의 오차를 줄이기 위해서 모델 보정(model updating)이 수행되었다.