• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.169-174
• /
• 2018

In this paper, a design method for a wideband LPF for harmonic suppression applications is investigated. The proposed wideband LPF is comprised of four circular slot pairs with different diameters, which are added symmetrically in the ground plane of a CPW transmission line. Four circular slot pairs act as a defected ground structure and provide a wideband low pass characteristic. The circular slot with the smallest diameter is located at the side of port 1, and the diameter of the circular slot is increased as it goes toward port 2. The low pass characteristics of each circular slot are compared with the proposed wideband LPF. The final designed LPF was fabricated on FR4 substrate, and its characteristics were tested. The measured S11 characteristic was maintained at over -3.3 dB in the frequency range of 1.89-20.00 GHz band, whereas the S21 characteristic was less than -21.4 dB in the frequency range of 2.66-20.00 GHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1445-1450
• /
• 2013

In this paper, a broadband series-fed bow-tie dipole pair (SBDP) antenna operating in the band of 1.7-2.7 GHz for mobile communication base station applications is proposed. The proposed antenna uses bow-tie-shaped dipole elements instead of straight strip dipole ones used in a conventional series-fed dipole pair (SDP) antenna. The simulation results show that the lowest operating frequency is shifted toward lower frequency as the flare angle increases, and so the lengths of the bow-tie dipole elements can be reduced in proportion to the frequency shift toward lower frequency. An SBDP antenna with a flare angle of 10 degrees is fabricated on an FR4 substrate (dielectric constant = 4.4 and thickness = 1.6 mm) and total width of the fabricated antenna is reduced by 10% compared to that of the conventional SDP antenna. The measured impedance bandwidth for voltage standing wave ratio (VSWR) < 2 is 48.8% (1.69-2.78 GHz), gain is 5.8-6.3 dBi, and the front-to-back ratio (FBR) is 14-17 dB.

• Korean Journal of Pharmacognosy
• /
• v.17 no.1
• /
• pp.73-77
• /
• 1986

Anthraquinones, physcion (I), mp $204{\sim}205^{\circ}$ and emodin (II), mp $254{\sim}255^{\circ}$, and $emodin-8-O-{\beta}-{_D}-glucoside$ (IV), mp $191{\sim}192^{\circ}$ together with ${\beta}-sitosterol$ glucoside (III), mp $280{\sim}282^{\circ}$ were isolated from the roots of Polygonum ellipticum Migo and P. sachalinense Fr. Schm. (Polygonaccae). Stilbene derivatives, 3,5,4'-trihydroxystibene (V), mp $258{\sim}260^{\circ}$ and $3,5,4'-trihydroxystilbene-3-O-{\beta}-{_D}-glucoside$ (VI), mp $142{\sim}144^{\circ}$ were also isolated.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.353-358
• /
• 2017

In order to reduce the size of the previous stepped slot antenna for UWB applications(3.1 ~ 10.6 GHz) to half, an open ended stepped slot antenna is proposed. The proposed antenna consists of a stepped slot etched on the ground plane as radiation part and a microstrip feed-line with rectangular patch on the top plane for wideband impedance matching. The proposed antenna is designed and fabricated on the FR4 substrate with dielectric constant of 4.3, thickness of 1.6 mm and size of $28.5{\times}32mm^2$. The measured impedance bandwidth (${\mid}S_{11}{\mid}{\leq}-10dB$) of the fabricated antenna is 7.99 GHz(3.01~11 GHz) which is sufficient to cover UWB band (3.1 ~ 10.6 GHz). In particular, it has been observed that antenna has a good omnidirectional radiation patterns and high gain over the entire frequency band of interest even though the size of the proposed antenna is reduced to half when compared with the previous antenna.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.40-50
• /
• 2023

Recently, the number of components of smartphones increases rapidly, while the PCB size continuously decreases. Therefore, 3D technology with a stacked PCB has been developed to improve component density in smartphone. For the s tacked PCB, it i s very important to obtain solder bonding quality between PCBs. We investigated the effects of the properties, thickness, and number of layers of interposer PCB and sub PCB on warpage of PCB through experimental and numerical analysis to improve the reliability of the stacked PCB. The warpage of the interposer PCB decreased as the thermal expansion coefficient (CTE) of the prepreg decreased, and decreased as the glass transition temperature (Tg) increased. However, if temperature is 240℃ or higher, the reduction of warpage is not large. As FR-5 was applied, the warpage decreased more compared to FR-4, and the higher the number and thickness of the prepreg, the lower the warpage. For sub PCB, the CTE was more important for warpage than Tg of the prepreg, and increase in prepreg thickness was more effective in reducing the warpage. The shear tests indicated that the dummy pad design increased bonding strength. The tumble tests indicated that crack occurrence rate was greatly reduced with the dummy pad.

• Korean Journal of Medicinal Crop Science
• /
• v.13 no.2
• /
• pp.80-84
• /
• 2005

Five known anthraquinones, physcion (1), I-O-methylemodin (2), emodin (3), $physcion-8-O-{\beta},-D-glucopyranoside$ (5), $emodin-8-O-{\beta},-D-glucopyranoside$ (6) and two known stilbenes, trans-resveratrol (4), $trans-resveratrol-3-O-{\beta},-D-glucopyranoside$ (7) were isolated from MeOH extract of Reynoutria sachalinensis (Polygonaceae). All structures were unambiguously established by 1D and 2D NMR and MS data and the compounds were evaluated for their cytotoxicity against L1210, HL-60, BI6F10 tumor cell lines in MTT assay. Among the compounds, trans-resveratrol (4) exhibited significant cytotoxic activity with $IC_{50}$ values of 9.2, 6.7 and $9.8\;{\mu}g/ml$, against the test cell lines respectively, but compounds 1-3 exhibited the moderate cytotoxic activity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.11
• /
• pp.1518-1523
• /
• 2018

A method for designing a DDQYA fed by a CPW is proposed in this paper. The proposed CPW-fed DDQYA consists of two series-connected strip dipoles, a ground reflector, and a strip-pair director. Instead of the conventional microstrip feed line in which the signal line is located on the substrate opposite to the antenna, a CPW is used because CPW is located on the same side with the antenna, and so the fabrication is easy. The strip-pair director is composed of two horizontally-separated strips, and it is added above the second dipole to enhance the gain in the high frequency region. A prototype of the proposed CPW-fed DDQYA is fabricated on an FR4 substrate. The fabricated antenna has a frequency band of 1.66-3.38 GHz(68.3%) for a voltage standing wave ratio < 2, and measured gain ranges 5.0-7.3 dBi over a frequency band of 1.60-2.90 GHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.471-472
• /
• 2015

In this paper, a design method for enhancing the gain of a series-fed dipole pair (SDP) antenna using mutiple directors is studied. Strip-type directors are located above the second dipole of the SDP antenna, and the variations of the input VSWR bandwidth and gain depending on the length of the second dipole and the number of directors are analyzed. The antenna is optimized to obtain gain > 8 dBi in the frequency range of 1.7-2.7 GHz, which has three directors in the optimum design. The optimized antenna is designed on an FR4 substrate with a dimension of 86.2 mm by 152.3 mm, and it has frequency bands of 1.67-2.79 GHz for a VSWR < 2 and 1.69-2.72 GHz for a gain > 8 dBi.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.549-555
• /
• 2011

In this paper, inverted triangle structural planar monopole antenna with Edge for UWB Communication (3.1 ~ 10.6 GHz) is presented. The antenna have broadband property structurally through inverted triangle structural planar monopole which have edge. Monopole and ground of proposed antenna exist on coplanar plane, and excite as CPW. It used FR4 dielectric substrate of ${\epsilon}_r=4.4$, and the size is $20{\times}20{\times}1.6mm$. Return loss is more than - 10dB in 3.1 ~ 10.1 GHz (7.0 GHz). Radiation pattern is about the same that of dipole antenna at all frequency. At measured result, max gain is 8.44 dBi at E - plane.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.59-60
• /
• 2017

In this paper, we studied a design method for obtaining broadband property by loading a chip capacitor on a coplanar waveguide(CPW)-fed compact quasi-Yagi antenna(QYA). The proposed antenna is a three-element QYA with dipole, reflector, and director. To reduce the size, the ends of both dipole and reflector are bent, and balun is incorporated in the antenna. To improve impedance matching, the loading position and capacitance value of chip capacitor were determined. From some simulations, the proposed antenna using an FR4 substrate with a size of 90 mm by 90 mm was designed for the operation in a broadband covering the UHF RFID and GPS systems. The antenna showed a good performance with a broadband of 850-1,626 MHz(62.7%) for a VSWR ${\leq}2$, a gain ${\geq}3dBi$, and a frong-to-back ratio ${\geq}4.6dB$.