• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.10
• /
• pp.1837-1844
• /
• 2016

This paper proposes an antenna of the fork type structure that operates in the UWB (Ultra Wide Band) frequency band (3.1 ~ 10.6 GHz). The proposed antenna is attached a circular patch in order to obtain the UWB band characteristics to the fork-type patch antenna. The ground plane is implemented in a arc-shape configuration. The effect of various parameters of the modified fork type radiating patch and partial arc ground plane for UWB operation is investigated. The proposed antenna is made of $34.0{\times}50.0{\times}1.0mm^3$ and is fabricated on the permittivity 4.4 FR-4 substrate. The experiment results shown that the proposed antenna obtained the -10 dB impedance bandwidth 8200 MHz (2.7 ~ 10.9 GHz) covering the UWB bands. This result satisfied the characteristics of ultra-wideband and the proposed antenna will be applicable to an ultra wideband system.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.178-182
• /
• 2002

Superconducting four-element patch array antenna was designed and fabricated using $high-T_{c}$ superconducting (HTS) thin film. The array antenna has single-feed circularly polarization and a resonance frequency of 11.85 GHz fur satellite communication system. To fabricate this antenna $YBa_2$$Cu_3$$O_{7-x}$(YBCO) superconducting thin films were deposited using rf-magnetron sputtering technique. Sequential rotation technique based on radiation elements($0^{\circ}$ , $90^{\circ}$, 1$80^{\circ}$, $270^{\circ}$ phase delay) was utilized to achieve circularly polarization. Simulated and measured results, the analysis on resonant frequency(fr), return loss, and bandwidth are presented. The results show that 10 dB return loss bandwidth of the array antenna is 11.04 GHz~12.59 GHz (13.15%) and 3dB axial ratio bandwidth is 11.42~12.52 GHz (9.2%).).).

• Journal of Navigation and Port Research
• /
• v.28 no.3
• /
• pp.213-219
• /
• 2004

In this paper, a LNA(Low Noise Amplifier) has been developed, which is operating at L-band i.e., 1452∼1492 MHz for satellite DAB(Digital Audio Brcadcasting) receiver. The LNA is designed to improve input and output reflection coefficient and VSWR(Voltage Standing Wave Ratio) by balanced amplifier. The LNA consists of low noise amplification stage and gain amplification stage, which make a using of GaAs FET ATF-10136 and VNA-25 respectively, and is fabricated by hybrid method. To supply most suitable voltage and current, active bias circuit is designed Active biasing offers the advantage that variations in $V_P$ and $I_{DSS}$ will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets $V_{gs}$ for the desired drain voltage and drain current. The LNA is fabricated on FR-4 substrate with RF circuit and bias circuit, and integrated in aluminum housing. As a reults, the characteristics of the LNA implemented more than 32 dB in gain. 0.2 dB in gain flatness. lower than 0.95 dB in noise figure, 1.28 and 1.43 each input and output VSWR, and -13 dBm in $P_{1dB}$.

• Journal of Korea Multimedia Society
• /
• v.22 no.6
• /
• pp.655-664
• /
• 2019

In this paper, we propose a novel way of combining multiple deep convolutional neural network (DCNN) architectures which work well for accurate video face identification by adopting a serial combination of 3D and 2D DCNNs. The proposed method first divides an input video sequence (to be recognized) into a number of sub-video sequences. The resulting sub-video sequences are used as input to the 3D DCNN so as to obtain the class-confidence scores for a given input video sequence by considering both temporal and spatial face feature characteristics of input video sequence. The class-confidence scores obtained from corresponding sub-video sequences is combined by forming our proposed class-confidence matrix. The resulting class-confidence matrix is then used as an input for learning 2D DCNN learning which is serially linked to 3D DCNN. Finally, fine-tuned, serially combined DCNN framework is applied for recognizing the identity present in a given test video sequence. To verify the effectiveness of our proposed method, extensive and comparative experiments have been conducted to evaluate our method on COX face databases with their standard face identification protocols. Experimental results showed that our method can achieve better or comparable identification rate compared to other state-of-the-art video FR methods.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.3
• /
• pp.50-56
• /
• 2010

In this paper, compact broad-band antenna using circular spiral slot and CPW (coplanar waveguide) feed is proposed. The proposed antenna is designed on the same plane of the substrate by using CPW fed structure, archimediean spiral slot structure. So it was achieved both the size of compact antenna and the broad band. A archimediean spiral slot structure is introduced for resonance of medium band operation. The distances of a CPW feeder line and a ground plane are modified for impedance matching and lower/higher band operation. The proposed antenna has a compact size ($8mm\;{\times}\;13mm$) and it is etched on the FR-4 (relative dielectric constant 4.4, thickness 0.8mm) dielectric substrate. The simulated impedance bandwidth (VSWR $\leq$ 2) and maximum gain of the proposed antenna are 5.98GHz (4.1GHz ~ 10.08GHz) and 3.97dBi, respectively. The measured impedance bandwidth (VSWR $\leq$ 2) and maximum gain of the proposed antenna are 6.02GHz (4.48GHz ~ 10.5GHz) and 2.68dBi, respectively. The simulation and measured result shows good impedance matching and radiation pattern over the interesting frequency bands. It can be applied to antenna of broad-band wireless communication system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1572-1579
• /
• 2009

In this dissertation ultra-broadband power amplifier(UPA) was designed and fabricated using negative feedback technique. UPA was made of pre-amplifier, drive amplifier and power amplifier. Negative feedback technique was used to achieve ultra-broadband performance. Designed power amplifier has 30dB gain and 2W output power. The load-pull data of power amplifier for optimal power matching was extracted from the measured S-parameter. Fabricated PCB material, permittivity is 4.6 and thickness is 0.8mm, is FR4 and UPA was fabricated 3 modules for comparison of the simulated and measured results. Size of the fabricated pre-amplifier and drive amplifier module is 40mm'50mm'16mm. And from the experimental results, gain of the pre-amplifier module is 9.87dB at 2GHz and flatness is 0.63dB. Experimental result of the drive amplifier module is 10.97dB at 2GHz and flatness of that is 0.26dB. Test result of the power amplifier module is 10.71dB at 2GHz and flatness is 0.72dB. Total size of the power amplifier is 45mm'134mm'16mm. According to the test results, gain of the UPA is 28.98dB at 2GHz and flatness is 1.68dB. Output power was 32.098dBm at 2GHz, 32.154dBm at 1GHz and 31.273dBm at 100MHz.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1406-1407
• /
• 2008

In this paper, a micro balanced filter in magnetically coupled LC resonators is proposed, designed, simulated by using FR-4 PCB substrate for low cost, small volume IEEE 802. 11a wireless LAN application. Two pair of coupled LC resonators using magnetic coupling of embedded inductors are applied to obtain bandpass transmission response and improve their phase and magnitude imbalance characteristics. In addition, high dielectric composite film is applied to fabricate the high Q MIM capacitors with small size and high capacitance density. It has an insertion loss of 1.4 dB, a return loss of 10 dB, a phase imbalance of 0.25 degree, and magnitude imbalance of 0.17 dB at frequency bandwidth of 200 MHz ranged from 5.15 GHz to 5.35 GHz, respectively. The proposed balanced filter has a small volume of $1.1mm{\times}1.3mm{\times}0.6mm$ (height).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4B
• /
• pp.388-396
• /
• 2002

In this paper, An aperture-coupled microstrip patch antenna operating at WLL frequency range(Rx : 2.3∼2.33Ghz, Tx : 2.37 ∼2.4Ghz) for WLL repeater is designed and fabricated. FR-4 epoxy substrate with 4.7 relative permittivity is inserted between feed-line and patch plane. Aperture-coupled structure is employed for consideration of bandwidth improvement and gain\`s characteristics. Air gap is arranged at each layer for bandwidth extension and radome is used as a protector in the upper patch. In this paper, both 1 port and 2 port are designed as 1$\times$2 array antenna which uses T-junction and λ$\_$g//4 transformer. Here, 1 port is used as transmitting/receiving antenna and 2 port is used as receiving antenna. Functionally independent two antennas using space diversity arrange slots between two antennas in order to be placed at the same place. As a result, we obtained a excellent isolation below -40dB and return loss is reduced by means of slots arrangement between patch and antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.941-948
• /
• 2005

In this paper, we have proposed a Ultra-Wideband slot notch antenna by using a semi-circular extension. The proposed antenna cover the entire UWB band(3.1${\~}$10.6 GHz) and notch out the IEEE 802.1la frequency band(5.15${\~}$5.825 GHz) by inserting a $\lambda$/4 length slot into the patch. A prototype antenna was fabricated on FR-4( ${\epsilon}_r$ =4.4, substrate thickness=0.8 mm) and measured for VSWR characteristics. The measured notched frequency variations versus frequency for different slot length. The path loss and group delay were measured. The proposed antenna also show a good gain flatness(1.9 dBi) except the IEEE 802.1la frequency band.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.4
• /
• pp.441-448
• /
• 2015

In this paper, a CPW-fed dual-band monopole antenna with two branch strips for WLAN(Wireless Local Area Networks) applications was designed, fabricated and measured. The proposed antenna is based on a CPW-feeding structure, and composed of two branch strips and then designed and tuned the length of two branch lines to obtained required frequencies bands. To obtain the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and carried out simulation about parameters $L_5$, $L_8$, $W_3$, $W_5$, $W_9$. The proposed antenna is fabricated on the FR-4 substrate using the obtained parameters. The numerical and experiment results demonstrated that the proposed antenna obtained the -10 dB impedance bandwidth 1,095 MHz (1.57~2.665 GHz) for 2.4 GHz band and 1,680 MHz (4.99~6.67 GHz) for 5 GHz band satisfied requirement while simultaneously covering the WLAN bands. And characteristics of gain and radiation patterns are determined for WLAN operating bands.