• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.308-311
• /
• 2011

In order to obtain mono-dispersed Fe NPs with high saturation magnetization, quantitative analysis method to investigate the growth dynamics of the Fe NPs synthesized by a conventional thermal decomposition method has been developed. As a result, fast nucleation process promotes formation of ~4 nm of initial nucleus with a non-equilibrium phase, resulting in low saturation magnetization. And slow particle growth with atomic-scaled surface precipitation mode (< 100 atoms/($min{\cdot}nm^2$)) can form the growth layer on the surface of initial nucleus with high saturation magnetization (~190 emu/$g_{Fe}$) as an equilibrium a phase of Fe. Therefore, higher stabilization of small initial nucleus generated just after the injection of $Fe(CO)_5$ should be one of the key issues to achieve much higher $M_s$ of Fe NPs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2019

This paper reports the microstructure and electrochemical properties of Si-Al-Fe ternary amorphous alloys prepared by rapid solidification as an anode for lithium secondary batteries. The microstructure was analyzed using XRD and HR-TEM with EDS mapping. In accordance with DSC analysis, annealing was performed to crystallize the active nano-Si in the amorphous alloy. Thus, nano-Si forms (~80 nm) embedded in the matrix alloy, such as $Fe_2Al_3Si_3$, $FeSi_2$, and $Fe_{0.42}Si_{2.67}$, were successfully synthesized. The electrode based on the Si-Al-Fe ternary alloy delivered an initial discharge capacity of approximately $700mAh^{g-1}$, and exhibited a high Coulombic efficiency of 99.0~99.6% from the $2^{nd}$ to $70^{th}$ cycles.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.226-232
• /
• 2002

We searched thermal stability of ${\alpha}-Fe_2O_3$ using red color filter for display. In the PDP(Plasma Display Panel), the color filter layer is lied normally between front glass and transparent dielectric materials, so it might be needed to study the reaction of ${\alpha}-Fe_2O_3$ and transparent dielectric materials. The transparent dielectric materials containing ZnO has good transparency. Red colorlayer of ${\alpha}-Fe_2O_3$ contacted with dielectric material layer containing ZnO is changed to colorlessness over 500$^{\circ}$C because ZnO defuse ${\alpha}-Fe_2O_3$, the dielectric materials without ZnO, however, maintain red color at the same condition. We suggest that a layer contacting with ${\alpha}-Fe_2O_3$ red color layer has to lie with transparent dielectric materials without ZnO, then the materials containing ZnO is coated over to get color of ${\alpha}-Fe_2O_3$ for red color filter

• Composites Research
• /
• v.21 no.5
• /
• pp.9-14
• /
• 2008

Carbon nanofibers (CNFs) were used as dielectric lossy materials and NiFe particles were used as magnetic lossy materials. Total twelve specimens for the three types such as dielectric, magnetic and mixed radar absorbing materials (RAMs) were fabricated. Their complex permittivities and permeabilities in the range of $2{\sim}18$ GHz were measured using the transmission line technique. The parametric studios for reflection loss characteristics of each specimen to design the single-layered RAMs were performed. The mixed RAMs generally showed the improved absorbing characteristics with thinner matching thickness. One of the mixed RAMs, MD3with the thickness of 2.00 mm had the 10 dB absorbing bandwidth of 4.0 GHz in the X-band ($8.2{\sim}12.4$ GHz). It also showed very broad 10 dB absorbing bandwidth as wide as 6.0 GHz in the Ku-band ($12.0{\sim}18.0$ GHz) with the thickness tuning to 1.49 mm. The experimental results for selected several specimens were in very good agreements with simulation ones in terms of the overall reflection loss characteristics and 10 dB absorbing bandwidth.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.13-16
• /
• 2000

In this study, we have fabricated nonequilibrium $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film, which contains an additional insoluble element Ag, by using DC magnetron sputtering method. We have investigated the magnetic properties of amorphous $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film as a function of rotational field annealing(RFA). After deposition, the amorphous $Fe_{85.6}Zr_{3.3}B_{5.7}Ag_{5.4}$ thin film annealed by rotational field annealing method at $350^{\circ}C$ for an hour was founded to have high permeability of 8680 of 100 MHz, 0.2 mOe, low coercivity of 0.86 De and very low core loss of 1.3 W/cc at 1 MHz, 0.1T.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.226-231
• /
• 1999

Pyroelectric infrared sensors have been fabricated using P(VDF/TrFE) film with pyroelectric effect. The weight percent and thickness of the poled P(VDF/TrFE) film are 75/25 percent and $25\;{\mu}m$ respectively. For easier fabrication and connection method new top and bottom electrodes design was adapted for human body detecting pyroelectric infrared sensor. An aluminum infrared absorption electrode and bottom electrode were deposited by thermal evaporator. And the device was mounted in TO-5 housing to detect infrared light of $5.5{\sim}14\;{\mu}m$ wavelength. The responsibility, NEP (noise equivalent power) and specific detectivity $D^*$ of the device were $9.62{\times}10^5\;V/W$, $3.95{\times}10^{-7}\;W$ and $5.06{\times}10^5\;cm/W$ under emission energy of $13\;{\mu}W/cm^2$ respectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.365-374
• /
• 2004

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. That is a cause of decreasing the durability of structure. In order to solve these problems, welding repair and strengthening methods can be considered. In general, cutting and welding procedure is carried out during the repair welding. Therefore, the investigation of the behavior of residual stress and deformation generated by cutting and welding is very important for safety of structure. Residual stress and deformation produced by gas cutting and arc welding were analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular direction of the cutting line and welding line was analyzed by the 2D-FEM was similar to that was analyzed by 3D-FEM. Therefore, it is possible to predict cutting and welding residual stress by 2D and 3D FEM.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.4
• /
• pp.169-176
• /
• 2016

This research explored the feasibility of preparing and utilizing preformed polymeric solution of Fe(III) as coagulants for water treatment. The differentiation and quantification of hydrolytic Fe(III) species in coagulant was done by utilizing spectrophotometric method based on the interaction of Fe(III) with Ferron as a complexing agent. The properties of the synthesized polymeric iron chloride (PICl) showed that the quantity of polymeric Fe(III) produced at r = 1.5 was 20% of the total iron in solution, as showing maximum contents. Coagulation experiments were conducted under the condition of various coagulant doses and pH for each coagulant prepared. From the comparison of the characterization of coagulation for $FeCl_3$ (r = 0.0) and PICl (r = 0.5, 1.0, 1.5) coagulants, PICl (r = 0.5, 1.0, 1.5) coagulants was found to be more effective than other coagulant for the removal of organic matters. The experimental results for the coagulation tests at various pH ranges showed that the PICl was least affected by the coagulation pH and PICl was very effective for the removal of turbidity and organic materials over wide pH range (pH 4-9) tested.

• Advances in concrete construction
• /
• v.13 no.1
• /
• pp.45-69
• /
• 2022

This paper investigates the shear behavior of reinforced concrete haunched beams (RCHBs) without stirrups. The research objective is to study the effectiveness of the ideal steel fiber (SF) ratio, which is used to resist shear strength, besides the influence of main steel reinforcement, compressive strength, and inclination angles of the haunched beam. The modeling and analysis were carried out by Finite Element Method (FE) based on a software package, called Atena-GiD 3D. The program of this study comprises two-part. One of them consists of nine results of experimental SF RCHBs which are used to identify the accuracy of FE models. The other part comprises 81 FE models, which are divided into three groups. Each group differed from another group by the area of main steel reinforcement (A_s) which are 226, 339, and 509 mm². The other parameters which are considered in each group in the same quantities to study the effectiveness of them, were steel fiber volumetric ratios (0.0, 0.5, and 1.0)%, compressive strength (20.0, 40.0, 60.0) MPa, and the inclination angle of haunched beam (0.0°, 10.0°, and 15.0°). Moreover, the parametric analysis was carried out on SF RCHBs to clarify the effectiveness of each parameter on the mechanical behavior of SF RCHBs. The results show that the correlation coefficient (R²) between shear load capacities of FE proposed models and shear load capacities of experimental SF RCHBs is 0.9793, while the effective inclination angle of the haunched beam is 10° which contributes to resisting shear strength, besides the ideal ratio of steel fibers is 1% when the compressive strength of SF RCHBs is more than 20 MPa.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.527-532
• /
• 2014

$0.97Bi_{0.5+x}(Na_{0.78}K_{0.22})_{0.5-3x}TiO_3-0.03LaFeO_3$ lead-free piezoelectric ceramics were fabricated by a solid state reaction method. $LaFeO_3$ additives were added to $Bi_{0.5}(Na_{0.78}K_{0.22})_{0.5}TiO_3$ for volatile compensation of bismuth and sodium ions in the sintering process. To create A-site vacancies, the mole ratio and charge valence of A-site ions ($Bi^{3+}$, $Na^+$ and $K^+$) were controlled. The improved piezoelectric properties were observed by addition of $LaFeO_3$ and control of A-site vacancies. In particular, a $d_{33}^*(S_{max}/E_{max})$ value of 614pm/V and an electric field induced strain of 0.33% was observed in $0.97Bi_{0.505}(Na_{0.78}K_{0.22})_{0.485}TiO_3-0.03LaFeO_3$ ceramic.