• Journal of electromagnetic engineering and science
• /
• v.15 no.3
• /
• pp.185-193
• /
• 2015

In this paper, a hybrid multiple input multiple output (MIMO) antenna for eight-band mobile handsets is designed and implemented. For the MIMO antenna, two hybrid antennas are laid symmetrically and connected by an interconnection tie, thereby enabling complementary operation. The tie affects both the impedance and radiation characteristics of each antenna. Further, printed circuit board (PCB) embedded type is applied to the antenna design. To verify the results of this study, we designed eight bands-LTE class 12, 13, and 14, CDMA, GSM900, DCS1800, PCS, and WCDMA-and implemented them on a bare board the same size as the real board of a handset. The voltage standing wave ratio (VSWR) is within 3:1 over the entire design band. Antenna isolation is less than -15 dB at the lower band, and -12 dB at the WCDMA band. Envelope correlation coefficient (ECC) of 0.0002-0.05 is obtained for all bands. The average gain and efficiency are measured to range from -4.69 dBi to -2.88 dBi and 33.99% to 51.5% for antenna 1, and -4.74 dBi to -2.97 dBi and 33.45% to 50.49% for antenna 2, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1455-1461
• /
• 2008

We implemented a subminiature internal antenna that is around 1 cc volume for the mobile phone. The fundamental type of studied antenna is IFA(Inverted F Antenna), and this antenna is designed to be improved efficiency and gain due to minimum current cancellation by the avoidance of multiple bending pattern. For the implementation of multiple band, helix is applied to compensate for short antenna length for low frequency band, and a 3 dimensional pattern is used for high frequency band. We made two kinds of 3D structure antenna. One is a 1 cc volume antenna for GSM/DCS band on the bare board set, and the other is a 1.5 cc volume for the GSM/USPCS mobile phone set. Measurements showed good gain performance that average gain of two antenna on each band are $-3.46{\sim}-0.45\;dBi$ and $-4.80{\sim}-3.29\;dBi$ respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.811-818
• /
• 2002

In this paper, a shorting pin and slot-loaded microstrip patch antenna is designed and fabricated. A shorting pin and slots are used for harmonic suppression on an inset fed antenna. A shorting pin and slot properties are analyzed by cavity model of the rectangular patch and the characteristics of the designed antenna are described. The designed antenna provides a gain of 7 dBi at the fundamental frequency, 5.8 GHz. In the second and third harmonic frequencies, the proposed antenna has gain suppression properties of -3.3 dB and -14.3 dB at each harmonic frequency, respectively.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.79-85
• /
• 2010

In this paper, a directive antenna design with a combination of electric-magnetic radiators for an radio frequency identification(RFID) system is presented. To generate a directive antenna radiation pattern, a structure combining a dipole and loop antenna is presented. A reader antenna and tag antenna are proposed for the RFID system. For the reader antenna, the frequency bandwidth defined by $S_{11}$<-10 dB is approximately from 820~990 MHz. The forward and backward gain differences are 1.5~2 dBi. For the tag antenna, the frequency bandwidth is approximately from 860~920 MHz with a maximum gain of 3.58 dBi at 910 MHz. In both cases, directive radiation characteristics are observed.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.293-296
• /
• 2005

This paper presents the design of linear and circular polarization baseball- shaped circular microstrip antenna (BCMA) with 3-dimensional structure using perturbation effect to reduce its size, which runs at 1.575GHz frequency bandwidth. As a result, the size of linear polarized antenna could be reduced up to 23.7% in patch diameter and 41.8% in its area. Linear polarized antenna has -26.04dB of return loss, 69MHz(4.38%) of -l0dB bandwidth, 4.51dBd of gain, and its -3dB beamwidth are 99$^{\circ}$ in E-plane, 83$^{\circ}$ in H-plane. Circular polarized antenna has -17.43dB of return loss, 113.7MHz(7.2%) of -l0dB bandwidth, 2dBd of gain, 2dB of axial ratio and its -3dB beamwidth are 87$^{\circ}$, 86$^{\circ}$ x-axis polarized, 80$^{\circ}$, 84$^{\circ}$ y-axis polarized. It has 82mm of diameter, which is 28.5% of linear polarized CMPA. Therefore, in this paper we verified that baseball-shaped 3-dimensional structure of circular microstrip patch antenna applied with perturbation effect is appropriate for miniaturization.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.3
• /
• pp.282-288
• /
• 2014

Recently there have been much interest in the GPS antenna performance improvement. In this paper, we propose very small patch antenna for GPS band. The proposed antenna resonance frequency was adjusted using the ground plane and variable capacitor connected the frame. The fabricated antenna was used a FR4 substrate by considering the difficulty and economical efficiency. Antenna measurement results was obtained good characteristics of VSWR 1.2, the passive antenna gain -0.60 dBi, the active antenna gain of 29 dB in center frequency of 1575.42 MHz GPS band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.930-935
• /
• 2009

This paper describes a miniaturezed metamaterial BT chip antenna for mobile devices. The size of the proposed antenna is $3.0\;mm(W){\times}2.0\;mm(L){\times}1.2\;mm(H)$. And it is fabricated by chip type. The zeroth-order resonant properties are analyzed by magnitude and phase distributions of the surface current using surface current scanning system. The antenna offers omni-directional radiation patterns and measured 3D average gain is over - 1.7 dBi.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.63-70
• /
• 2012

This paper discussed on the directive gain improvement method of the U-type ultra wide-band(UWB) planar patch antenna model with CPW feeding. For directive gain improvement, the U-type printed patch antenna model with CPW feeding is reconstructed as a microstrip structure by adding a reflection plane with aperture slot. The reflection coefficient of the reconstructed antenna is less than -6.5 dB(VSWR < 3.3) to the characteristic impedance of $50.08{\Omega}$ and showed the directive radiation patterns with the directive gain of 7.5 dBi ~ 10.1 dBi, the front-back ratio of 17.8 dB ~ 28.7 dB and the range of -3dB radiation angle over ${\pm}30^{\circ}$ to the main beam direction of ${\theta}=0^{\circ}$.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.173-176
• /
• 2012

This paper introduces a novel horn antenna for circular polarization using a planar-type radiator. This antenna can be divided to two parts, microstrip antenna and square horn. The microstrip antenna has the role of feeder and polarizer of the horn antenna, and it is designed to stacked type having metal spacer for high gain, high isolation and wideband characteristic. Using the proposed antenna structure, the horn antenna needs not additional structure such as feeder and polarizer, and the size of it can be considerably reduced. The horn antenna has typical gain of 8dBi and 3-dB axial-ratio bandwidth around 4.9%.This antenna can widely used for various antenna system for mobile and satellite communication using circular polarization expecially in high frequency band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1034-1039
• /
• 2002

In this paper, the design of a dual-polarization rectangular microstrip patch antenna with high isolation between two feeding ports excited by using both an aperture-coupled feed (port 1) and a 3-dimensional microstrip feed (port 2) is presented. From the simulation using the commercial program IE3D, the optimum values of the antenna parameters are investigated at both two feed structures and the optimum antenna is designed and fabricated. Experimental results confirmed that an bandwidth of the antenna is about 17 % and the isolation of two ports is great than 30 dB over all frequency bands.