• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.86-93
• /
• 2008

A low-power, low-noise, highly-linear hybrid balun circuit is proposed for 2.4-GHz fully differential CMOS direct conversion receivers. The hybrid balun is composed of a passive transformer and loss-compensating auxiliary amplifiers. Design issues regarding the optimal signal splitting and coupling between the transformer and compensating amplifiers are discussed. Implemented in $0.18{\mu}m$ CMOS process, the 2.4 GHz hybrid balun achieves 2.8 dB higher gain and 1.9 dB lower noise figure than its passive counterpart and +23 dBm of IIP3 only at a current consumption of 0.67 mA from 1.2 V supply. It is also examined that the hybrid balun can remarkably lower the total noise figure of a 2.4 GHz fully differential RF receiver only at a cost of 0.82 mW additional power dissipation.

• Explosives and Blasting
• /
• v.41 no.3
• /
• pp.38-61
• /
• 2023

An Excavation Damaged Zone(EDZ) caused by blasting impact changes rock properties, in situ stress distribution, etc., and its effects are noticeable at around a radioactive waste repository located at deep underground. In particular, the increase in permeability due to the formation of cracks may significantly increase the amount of groundwater inflow and the possibility of radioactive nuclide outflow. In this study, FLAC2D and FLAC3D were used to analyze the mechanical and thermal behaviors for three categories: a)No EDZ, b)Uniform EDZ, and c)Random EDZ. It was found that the tunnel displacement in the Random EDZ case was 423% higher than that in the No EDZ case and was 16% higher than that in the Uniform EDZ case. Tunnel inflow in the Random EDZ was also 17.3% and 10.8% higher than that in the No EDZ and the Uniform EDZ case, respectively. The permeability around the tunnel was increased by up to 10 times in the corner of the tunnel wall and roof due to the stress redistribution after excavation. From the computer simulation, it was found that the permeability around the tunnel wall was partially increased but the overall tunnel inflow was decreased with increase of stress ratio. Mechanical analysis using FLAC 3D showed similar results. Slight difference between 2D and 3D could be explained with the development of plastic zone during the advance of tunnel excavation in 3D.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.4
• /
• pp.229-233
• /
• 2015

In this paper, in order to develop outstanding Pb-free piezoelectric composition ceramics, the $(Na_{0.525}K_{0.443}Li_{0.037})(Nb_{0.883}Sb_{0.08}Ta_{0.037})O_3+0.3wt%Bi_2O_3+0.4wt%Fe_2O_3+xwt%CuO$ (x= 0~0.8 wt%)(abbreviated as NKL-NST) lead-free piezoelectric ceramics have been synthesized using the ordinary solid state reaction method. The effects of CuO-doping on the structure and electrical properties of the NKL-NST ceramics were systematically studied. The results show that the ceramics exhibit a pure perovskite structure with orthorhombic phase at room temperature, and secondary phase was found in the ceramics. The 0.4 wt%CuO added ceramics sintered at $950^{\circ}C$ showed the optimum properties of piezoelectric constant($d_{33}$), planar piezoelectric coupling coefficient(kp) and mechanical quality factor(Qm) : $d_{33}=213$[pC/N], kp= 0.43, Qm= 423,respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.219-220
• /
• 2006

In this study, m order to develop multilayer ceramics vibrator for ultrasonic nozzle, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the aomunt of PbO. With increasing PbO contents. secondary phases were increased and phase structure were changed from tetragonal structure to rhombohedral structure and also electromechanical coupling factor were linearly decreased. At the composition ceramics with the sintering temperature of $870^{\circ}C$ and 1 mol% excess PbO, density, electromechanical coupling factor, dielectric constant, piezoelectric d constant and mechanical quality factor showed the optimum value of $7.879g/cm^2$, 0.55, 1149, 328pC/N, 1224, respectively for multilayer ceramics vibrator application for ultrasonic nozzle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.205-209
• /
• 2016

In this paper, piezoelectric ceramics with the composition of $(Na_{0.525}K_{0.4425}Li_{0.0375})(Nb_{0.8975}Sb_{0.065}Ta_{0.0375})O_3+0.3wt%\;CoO+x\;CuO$ ($0.005{\leq}x{\leq}0.025$) (abbreviated to NKL-NST) were fabricated for ultrasonic sensor application. The effects of CuO addition and sintering on the microstructure and the piezoelectric properties of the NKL-NST ceramics were systematically studied. Excellent piezoelectric properties such as electromchanical coupling $factor(k_p)=0.415$, piezoelectric constant $(d_{33})=166pC/N$ and piezoelectric figure of merit $d_{{33}*}g_{33}=5.47pm^2/N$ were obtained from the 2.5 mol% CuO doped NKL-NST+0.3 wt%CoO ceramics sintered at $1,000^{\circ}C$ for 3 h.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.1000-1004
• /
• 2008

In this paper, the influences of poling electric field on piezoelectric properties of $0.95(K_{0.5}Na_{0.5})NbO_3$-$0.05Li(Sb_{0.8}Nb_{0.2})O_3$ (abbreviated as KNN-LSN) ceramics were investigated. The specimens was sintered at sintering temperature of $1050^{\circ}C$. They showed orthorhombic phase structure without secondary phase. Electromechanical coupling factor (kp), dielectric and piezoelectric constant($d_{33}$) increased with poling electric field. However, mechanical quality factor (Qm) decreased. Take into account of poling conditions and piezoelectric properties of KNN-LSN ceramics, the optimum poling condition for KNN-LSN ceramics was poling electric field of 4.5 kV/mm. At the time, kp of 0.458, Qm of 43.97, $d_{33}$ of 278 pC/N, and dielectric constant of 1079 were shown, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.455-459
• /
• 2001

In this paper, the dielectric and pizoelectric properties of 0.05Pb(M $n_{04}$ $W_{0.2}$N $b_{0.4}$) $O_3$-0.95(PbZ $r_{x}$ $Ti_{1-x}$ ) $O_3$+yN $b_2$ $O_{5}$ , are investigated as a function of the mole ratio of Zr and the amount of N $b_2$ $O_{5}$ . Also, the phase is analyzed by XRD. When the mole ratio of Zr is 0.51, the electromechanical coupling coefficient( $k_{p}$ ), relative dielectric constant ($\varepsilon$$^{T}$ $_{33}$ /$\varepsilon$$_{0}$ ), piezoelectric stain constrain ( $d_{33}$ and dielectric loss tangent show maximum, while the mechanical quality factor shows minimum value ; $k_{p}$ =56.5%, $d_{33}$ =258pC/N, $\varepsilon$$^{T}$ $_{33}$ /$\varepsilon$$_{0}$ =1170, $Q_{m}$ =1150, tan$\delta$=0.51%. At that composition, MPB which rhombohedral and tetragonal phase coexist in this ternary system is shown by the results of XRD analysis. Also, when the amount of N $b_2$ $O_{5}$ is 0.3wt%, the mechanical quality factor is increased to about 2000. The phase transition temperature of the ternary piezoelectric ceramic system showed about 35$0^{\circ}C$.TEX>.>.>.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.901-905
• /
• 2008

In this study, $0.95(K_{0.5}Na_{0.5})NbO_{3}-0.05Li(Sb_{0.8}Nb_{0.2})O_{3}+0.2\;wt%Ag_{2}O$ were investigated as a variations of sintering times in order to improve dielectric and piezoelectric properties of lead-free piezoelectric ceramics. $Ag_{2}O$ were used as sintering aids and the specimens were sintered during 3, 5, 7, 9 and 11 hours, respectively. At the specimen sintered during 7 hour, Electromechanical coupling factor ($k_p$), density, dielectric constant (${\epsilon}_{\gamma}$), piezoelectric constant ($d_{33}$) and curie temperature ($T_c$) of composition ceramics showed the optimal value of 0.450, 4.274 $[g/cm^3]$, 1007, 257 [pC/N] and $396^{\circ}C$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.146-153
• /
• 1998

The optical near-field patterns, propagation loss and mode sizes of x-cut $Ti:LiNbO_3$ optical waveguide which was fabricated by Ti-diffusion varying with Ti strip thickness in wet oxygen atmosphere were discussed at optical wavelength 1550nm. As Ti thickness increased from $760{\AA}$, the insertion loss of waveguide was decreased. But at Ti thickness $1500{\AA}$, mode sizes are widely broadened. The Ti thickness of below $1100{\AA}$ and above $1500{\AA}$ showed negative effects to propagation loss and fiber coupling. The best Ti thickness for fabricating low propagation loss and good fiber coupling was inferred to be between $1100{\AA}-1500{\AA}$ in our conditions. And for Ti thickness $1150{\AA}$, its propagation loss, horizontal/vertical mode sizes were showed 1.61 dB/cm, $11.9/8.9{\mu}m$ for TM, 0.22 dB/cm, $12.0/9.1{\mu}m$ for TE respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.60-63
• /
• 1997

Dieletric ailed piezoelectric properties of Pb[$Zr_{0.45}$/ $Ti_{0.5-x}$/L $u_{x}$ (M $n_{1}$3//S $b_{2}$3)$_{0.05}$] $O_3$(0$\leq$x $\leq$0.03) were investigated. The partial substitution of $Ti^{4+}$ by a L $u^{3+}$ permitted improvement of the piezoelectric constant( $d_{33}$ ), electromechanical coupling factor ( $k_{p}$ ) and dielectric constant($\varepsilon$$_{33}$ /Sup T/). The dielectric loss(tan $\delta$ ) increased and mechanical quality factor(Qm) decreased with an increase of x were observed. A new piezoelectric material for actuator application was developed at x=0.02 with $d_{33}$ =370$\times$10$^{-2}$ /C/N, $k_{p}$ =58.5%, $\varepsilon$$_{33}$ $^{T}$ =1321, $Q_{m}$ =714 and tan $\delta$ =0.98%.%..%.%.