• Structural Engineering and Mechanics
• /
• 제19권3호
• /
• pp.337-346
• /
• 2005

The paper reports on a study of bond strength between reduced-water-content concrete and tensile reinforcement in spliced mode. Three different diameters (12, 16 and 22 mm) of tensile steel were spliced in the constant moment zone, where there were two bars of same size in tension. For each diameter of reinforcement, a total of nine beams ($1900{\times}270{\times}180mm$) were tested, of which three beams were with no axial force (positive bending) and the other six beams were with axial force (combined bending). The splice length was selected so that bars would fail in bond, splitting the concrete cover in the splice region, before reaching the yield point. It was found that there was a considerable size effect in the experimental results, i.e., as the diameter of the reinforcement reduced the bond strength and the deflection recorded at the midspan increased significantly, whilst the stiffness of the beams reduced. It was also found for all reinforcement sizes that higher bond strength and stiffness were obtained for beams tested in combined bending than that of the beams tested in positive bending only.

• 비파괴검사학회지
• /
• 제29권5호
• /
• pp.415-420
• /
• 2009

이 논문은 표면파의 비선형특성을 이용하여 재료 표면의 열화손상을 평가한 사례 연구의 결과를 보고한다. 이 연구에서는 3점 굽힘 피로시험에 의해 표면에 피로열화를 가한 알루미늄 T6 시편을 대상으로 표면파의 음향 비선형 파라미터를 측정하기 위한 실험장치를 구성하였으며, 피로시험 전후에서 측정된 비선형파라미터의 크기를 비교하였다. 특히 3점 굽힘 피로시험에 의한 표면피로손상은 시편의 중앙부 표면에 집중 될 것이 예상되므로 이 주변에서의 비선형 파라미터의 변화를 세밀히 관찰하였다. 실험결과 피로손상이 거의 없는 시편의 가장자리에서는 비선형 파라미터가 피로시험 전후에서 큰 변화가 없었지만, 표면 피로열화가 집중된 중앙부에서는 뚜렷하게 증가하는 것으로 나타났다.

• 한국분말재료학회지
• /
• 제11권5호
• /
• pp.412-420
• /
• 2004

The purpose of the present study is to determine an optimum composition using cheaper powders keeping with high performance of hard rock cutting diamond saw blade. With 50Fe-20(Cu . Sn)-30Co specimen, a part of Co was replaced by Ni(5%, 10%, and 15%, respectively). These specimens were hot pressed and sintered for predetermined time at various temperature. Sintering is performed by two different methods of temperature controlled method and specimen dimension controlled method. In order to determine the property of the sintered diamond saw blade, 3 point bending tester, X-ray diffractometer, and SEM were used. As the Co in the bond alloy was replaced by Ni, the hardness of the specimen increased. Thus the 50Fe-20(CuㆍSn)-15Co-15Ni specimen showed the maximum hardness of 104(HRB). The results of 3 point bending test showed that flexure strength decreased along with increase in Ni content. This is attributed to the formation of intermetallic compound(Ni$_{x}$Sn) determined by X-ray diffraction. The fracture surface after 3 point bending test showed that diamond was fractured in the specimen containing 0%, 5%, and 10%Ni, and the fracture occurred at the interface between diamond and matrix in the specimen containing 15%Ni. The cutting ability test showed that the abrasive property was not changed in the specimen containing 0%, 5%, and 10%Ni. The optimum composition determined in this study is 50Fe-20(CuㆍSn)-20Co-10Ni.

• 한국산학기술학회논문지
• /
• 제20권7호
• /
• pp.166-172
• /
• 2019

금속 일체형 판재 도어 임팩트 빔 개발을 위해 단면 형상의 최적설계를 진행하였다. 기존의 도어 임팩트는 충격을 흡수하는 강관과 양쪽에 브라켓을 용접하여 자동차에 설치하는 구조로 이루어졌다. 하지만, 브라켓을 설치하기 위한 용접작업은 생산성을 떨어뜨리고 생산단가를 증가시키는 과정이다. 이러한 단점을 극복하기 위해 일체형 판재 도어 임팩트 빔의 개발은 반드시 필요한 공정이다. 본 논문에서는 일체형 판재 도어 임팩트의 단면 형상을 수치해석의 방법으로 제안하는 연구를 진행하였다. 외부 충격에 대한 반력 하중 및 생산성을 고려하여 엔지니어의 직관적인 설계 형상 6가지에 대하여 수치해석을 진행하였다. 객관적인 비교를 위해 3점 굽힘 하중 실험을 모사하는 유한요소해석을 진행하였다. 형상과 치수가 상이한 6가지의 단면 형상 중 최적의 형상을 선정하고, 상세 설계를 위해 단면형상의 높이와 폭의 치수를 변화시키며 해석을 진행하였다. 이를 통해, 일체형 판재 도어 임팩트의 최적의 단면 형상을 제안하였다.

• 한국압력기기공학회 논문집
• /
• 제11권2호
• /
• pp.40-44
• /
• 2015

The fatigue behavior of thermal butt fusion in safety class III high-density polyethylene (HDPE) buried piping for nuclear power plants was investigated using load-controlled bending fatigue on four-point bend test specimens. Based on the results, the presence of thermal butt fusion beads was confirmed to reduce the fatigue lifetime in the low- and medium-cycle fatigue regions while having a negligible effect in the high-cycle fatigue regions.

• 한국세라믹학회지
• /
• 제35권6호
• /
• pp.551-558
• /
• 1998

Detection of microcrack in {{{{ {Al }_{2 } {O }_{3 } }} ceramics were studided by AE(acoustic emission) technique with 4-point bending test in order to evaluate the fracture process and formation of microcrack. Fully-dense alu-mina ceramics having a different grain size were fabricated by varing the hot-pressing temperature. The grain size of alumina increased with increasing the hot-pressing temperature whereas the bending strength decreasd. The microcracks were observed by SEM and TEM. The generation of AE event increased with increasing the applied load and many AE event was generated at maximum applied load. Alumina with smaller grain size shows the generation of many AE event resulting in an increase of microcrack formation. An intergranular fracture is predominantly observed in fine-grained alumina whereas intragranular fracture occurs predominantly in coarse-grained alumina,. Analysis of micorstructure and AE prove that primary mi-crocracks occur within grain-boundaries of alumina. The larger microcracking were formed by the growth and/or coalesence of primary microcracks. Then the materials become to fracuture by main crack gen-eration at the maximum applied load.

• 한국세라믹학회지
• /
• 제36권9호
• /
• pp.997-1005
• /
• 1999

• 한국농공학회지
• /
• 제24권3호
• /
• pp.92-99
• /
• 1982

The objective of this study was to investigate the compressive and bending strength characteristics of epoxy resin mortar, which is still in an early stage of its use and study in Korea. The results obtained are summarized as follows; 1. The compressive strengths of epoxy resin mortar after 1 day, 2 days and 3 days were gained 87%, 91% and 95%, respectively, in view of that of mortar at the age of 7 days. This result showed that the initial compressive strength within 1 day was very high. 2. The highest compressive strength of epoxy resin mortar was 914 kg/cm2 at the point of having the mixing ratio of one to two. It reached up to 3.7 times that of the normal portland cement mortar at the age of 28 days. 3. The bending strengths of epoxy resin mortar after 1 day, 2 days and 3 days came up to 88%, 93% and 97%, respectively, in comparing that of mortar at the age of 7 days. It was expressed to be simielar to the tendency of compressive strength. 4. The highest bending strength of epoxy resin mortar was 384 kg/cm2 at mixing ratio of one to two. It came up to as much as 6.5 times in comparing with that of the normal portland cement mortar at the age of 28 days. Therefore, the epoxy resin mortar would be effective for promoting the bending strength of structural members. 5. The regression equation between compressive and bending strength was obtained as follows; oo~=0.391 oc+27.54 (r=0.99) And the estimated value of bending strength was corresponded to about 44 per cent in comparing with that of the compressive strength.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.957-962
• /
• 2009

Sialon was produced by hot-pressing the mixtures of $Si_3N_4$, AlN and $Y_2O_3$ powders. All fracture tests were performed on a three-point loading system with a 30 mm bending span. Fracture toughness and Vickers hardness of smooth specimen were average 7.05 $MPa{\cdot}m^{0.5}$ and Hv = 1580, respectively. Density of three kinds of specimens, smooth specimen, smooth and healed specimen, smooth with $SiO_2$ colloidal coating and healed specimen, had beyond 99 % of theoretical density. Bending strength of smooth healed specimens had high strength more than 1 GPa. Crack healed specimens recovered as strength as smooth specimen. That is, cracked specimen with $SiO_2$ colloidal coating on cracked part recovered strength by heat treatment, completely. Crack healing of $Si_3N_4$ composite ceramics had contributed glassy $SiO_2$ to strength recovery. Limiting high temperature for bending strength of heat treated smooth specimen for bending strength was about 1273 K.

• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.63-67
• /
• 2016

본 논문에서는 폴리머 기반의 유연 기판 위 적층 된 다양한 필름의 굽힘 탄성계수의 간접 측정법을 소개한다. 패키징 기판의 다양한 적층 재료들의 탄성계수는 기계적으로 신뢰성 있는 전자기기 개발에 결정적이지만, 기판과 매우 견고히 접합하고 있는 적층 필름을 온전히 떼어 내어 자유지지형(free-standing) 시편을 만들기 어렵기 때문에 그 측정이 쉽지 않다. 이를 해결하기 위해 본 연구에서는 필름-기판의 복합체 시편에 대한 3점 굽힘을 진행하였고 시편 단면에 면적 변환법(area transformation rule)을 적용한 응력 해석을 수행하였다. 탄성계수를 알고 있는 기판에 대하여, 굽힘 시험으로 얻은 다층 시편의 강성으로부터 필름과 기판의 탄성계수 비를 계산하였으며, 전기 도금 구리 시편을 이용하여 양면 적층, 단면 적층의 두 가지 해석 모델이 실험 평가되었다. 또한 주요 절연체 적층 재료인 prepreg (PPG)와 dry film solder resist (DF SR)의 굽힘 탄성계수가 양면 적층 시편 형태로 측정 되었다. 결과로써 구리 110.3 GPa, PPG 22.3 GPa, DF SR 5.0 GPa이 낮은 측정 편차로 측정 됨으로써 본 측정법의 정밀도와 범용성을 검증하였다.