• 한국해양공학회지
• /
• 제10권4호
• /
• pp.38-50
• /
• 1996

Recently carbon fiber reinforced plastic (CFRP) has been used structural materials in corrosive environment such as for water, chemical tank and pipes. However, mechanical properties of such materials may be change when CFRP and exposed to corrosive environment for long periods of time. The degradation behavior of carbon fiber/epoxy resin composite material in distilled water is investigated using acoustic emission (AE) technique, Fracture toughness tests are performed on the compact tension specimens that are pilled by two types of $[O_2/9O_2]_{3s}$ and $[O/9O]_6s$. During the testes, AE test was carried out to monitor the damage of CFRP by moisture absorption. The data was treated by 2-parameter Weibull distribution and the fracture surface was observed by scanning electron microscope.

• 한국공작기계학회논문집
• /
• 제12권4호
• /
• pp.9-16
• /
• 2003

In this study, the decision of dressing time for diamond wheel was analyzed by observing with acoustic emission signals and surface roughness, and also obtained the machining characteristics by weibull distribution plot for the values of bending strength. From the experimental study, it was possible to predict the time of re-dressing for the diamond grinding wheel with the analysis of acoustic emission signals and surface roughness values, and following conclusions were obtained. The root-mem-square values of acoustic emission signals were obtained low as the increased of table speed for different abrasive grain size. This is caused by the lack of grinding power which is not able to get rid of all real grinding mass of depth as the table speed is increased. The values of bending strength for ground $Si_3 N_4$ specimens were decreased for gain size of #400 than that of #60, but it was found that the surface roughness values for gain size of #60 were better than that of #400. As compared the shape parameter of weibull distribution plot for the values of bending strength, it was found that the reliability of bending strength for grain size of #60 increased than that of #400.

• 한국농공학회논문집
• /
• 제51권4호
• /
• pp.49-55
• /
• 2009

This paper is to induce design floods through L-moment with 3 and 4 parameter Kappa distributions including test of independence by Wald-Wolfowitz, homogeneity by Mann-Whitney and outlier by Grubbs-Beck on annual maximum flood flows at 9 water level gaging stations in Han, Nakdong and Geum Rivers of South Korea. After analyzing appropriateness of the data of annual maximum flood flows by Kolmogorov-Smirnov test, 3 and 4 Kappa distributions were applied and the appropriateness was judged. The parameters of 3 and 4 Kappa distributions were estimated by L-moment method and the design floods by water level gaging station was calculated. Through the comparative analysis using the relative root mean square errors (RRMSE) and relative absolute errors (RAE) calculated by 3 and 4 parameter Kappa distributions with 4 plotting position formulas, the result showed that the design floods by 4 parameter Kappa distribution with Weibull and Cunnane plotting position formulas are closer to the observed data than those obtained by 3 parameter Kappa distribution with 4 plotting position formulas and 4 parameter Kappa distribution with Hazen and Gringorten plotting position formulas.

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.681-688
• /
• 2019

SM45C steel, which is widely used for mechanical structure, was carburized at 870℃ for 4 hours and tempered at 300℃ and 400℃ for 1, 3 and 6 hours. The tempered materials were evaluated for tensile test, hardness test and impact test. In particular, the hardness and the absorption energy were evaluate the reliability by the Weibull statistical analysis. 300℃-1h specimen is considered to be the best heat treatment condition in the tensile stress and the observation of fracture surface. 300℃-1h specimen showed larger shape and scale parameter than the other specimens, and Rockwell hardness variance was small and showed the best characteristics. 400℃-3h specimen showed larger shape and scale parameter than the other specimens, the dispersion of impact absorption energy is small, and showed excellent characteristics.

• 품질경영학회지
• /
• 제9권1호
• /
• pp.3-11
• /
• 1981

동일한 부품 K개를 갖고 있으며, 그 중에서 S개 이상의 스트렝스(strength)가 스트레스(stress) 보다 크게 될 경우 신뢰성이 유지되는 시스템에서 스트레스와 스트렝스가 모두 와이블(weibull) 분포를 하고 있을 때의 시스템 신뢰성을 고찰하였다. 2 절에서는 시스템 신뢰성의 최소분산불편추정량(MVU estimator)을 구하였고, 3 절에서는 최소분산불편추정량의 점근분포(asymototic distribution)를 구하고 표본크기가 클때 시스템 신뢰성의 최소분산불편추정량과 최우추정량(MLE)과의 관계를 구하였으며, 4 절에서는 시스템 신뢰성의 일양최적불편신뢰구간(uniformly most accurate unbiased confidence interval) 을 구하였고, 5 절에서는 몬데 카를로 씨뮤레이션(Monte Carlo Simulation)을 사용하여 작은 표본에서의 최우추정량과 최소분산불편추정량의 편기(bias)와 평균자승오차(MSE)를 비교하였고 6 절에서는 결과를 간단히 요약하고 본 논문을 더 확장할 경우에 문제점을 제시하였다.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2421-2428
• /
• 2002

In this study, the failure probability of the degraded LP turbine blade steel was performed using the Monte Carlo simulation to apply variation of applied stress and strength. For this purpose, applied stress under the service condition of steady state was obtained by theoretical stress analysis and the maximum Von-Mises stress was 219MPa. The fatigue strength under rotating-bending load was evaluated by the staircase method. Furthermore, 3-parameter Weibull distribution was found to be most appropriate among assumed distributions when the probabilistic distributions of tensile and fatigue strength were determined by the proposed analysis. The failure probability with various loading conditions was derived from the strength-stress interference model and the characteristic factor of safety was also estimated.

• 신재생에너지
• /
• 제4권3호
• /
• pp.15-22
• /
• 2008

The effects of design parameters for small scale hydro power (SSHP) plants due to rainfall condition have been studied. The model to predict hydrologic performance for SSHP plants is used in this study. The results from analysis for rainfall conditions based on Weibull distribution show that the capacity and load factor of SSHP site had large difference between the variation of shape and scale parameter. Especially, the hydrologic performance of SSHP site due to variation of shape parameter varied more sensitive than the case of variation of scale parameter. And also, the methodology represented in this study can be used to decide the primary design specifications of SSHP sites.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.143-151
• /
• 1999

The shape of surface micro-crack is very irregular due to nonhomogeneous microstructure but is very important in respect to qualitative estimation of fatigue life. Fractal geomety can quantify the shape of surface mciro-crack. Fractal dimension is measured for surface micro-cracks with coast line and box counting method and estimates cycle ration in Al 2024-T3. The average fractal dimension $D_{favg}$ of surface micro-cracks has 3-parameter weibull distribution and location parameter is nearly constant but shape parameter decreases as cycle ration increases. The fractal dimension by coast line method is measured for individual surface micro-crack but the fractal dimension by box countin method is measured for all the surface micro-cracks under sampling area. Therefore, This paper shows fractal dimension $D_{fb}$ can predict cycle ratio $N/N_f$ more convenient than fractal dimension $D_{favg}$.

• 대한기계학회논문집A
• /
• 제38권9호
• /
• pp.999-1004
• /
• 2014

본 연구에서는 마찰교반용접된 AA7075-T651 판재의 피로균열전파저항의 공간적 불규칙성에 미치는 초기균열위치의 영향에 대하여 고찰되었다. 본 연구의 목적은 3가지 다른 초기균열위치에 따른 피로균열전파저항의 통계적 성질을 특성화하는 것이다. 본 연구에서는 피로균열전파저항 계수를 하나의 확률과정으로 취급하였다. 본 연구를 통하여 모든 초기균열위치의 시험편에 대한 피로균열전파저항 계수는 2-파라메터 Weibull 분포에 잘 따름을 알 수 있었다. 피로균열전파저항 계수의 확률분포의 형상 파라메터는 BM-ICL 시험편이 7.50으로 가장 크게 나타났으며, WM-ICL 시험편이 2.61로 가장 낮았다. 또한 피로균열전파저항 계수의 자기상관함수는 초기균열위치 시험편에 관계없이 모두 지수함수로 평가될 수 있음을 알았다.

• Asian Journal of Atmospheric Environment
• /
• 제9권4호
• /
• pp.288-297
• /
• 2015

In this study, wind conditions and its energy potential have been assessed by conducting a Weibull analysis of the wind speed data (over the period of 2002-2011) measured from a port city (Mongla) and an isolated island (Sandwip) in Bangladesh. The monthly mean wind speed at Mongla ranged from 1.60 m/s (December) to 2.47 m/s (April). The monthly values of Weibull shape parameter (k) were from 1.27 to 2.53. In addition, the values of the scale parameter (c) and the monthly wind power density ranged from 1.76 to 2.79 m/s and 3.95 to $17.45W/m^2$, respectively. The seasonal mean wind speed data varied from 1.72 (fall) to 2.29 m/s (spring) with the wind power density from 5.33 (fall) to $14.26W/m^2$ (spring). In the case of Sandwip, the results were comparable to those of Mongla, but moderate reductions in all the comparable variables were observed. The wind data results of these two areas have been compared with those of eight other locations in the world with respect to wind power generation scale. According to this comparison, the wind power generation scale for Mongla and Sandwip was adequate for stand-alone small/micro-scale applications such as local household consumption, solar-wind hybrid irrigation pumps, and battery charging.