• 소성∙가공
• /
• 제22권3호
• /
• pp.133-142
• /
• 2013

Recently, electric vehicles and hybrid cars are being promoted as alternatives to reduce automobile emissions. Generally, thin sheet materials such as aluminum alloy AA300X and cold-rolled steel sheet such as JIS-G-3141 are used for the container for the lithium-ion secondary batteries. In this study, a multi-stage deep drawing process is used to produce a rectangular cup from thin stainless steel sheet material, SUS409L, with an initial blank thickness of 0.4mm for the battery container application. Numerical simulations of the first through the fifth stages for the multi-stage deep drawing with thin SUS409L sheet were conducted using LS-Dyna3D Implicit/Explicit. Special consideration was given to the deformation characteristics due to the normal anisotropy of the sheet material. The numerical simulations were conducted with both isotropic properties and the anisotropic properties of the initial blank material. An unexpected forming failure, barreling in the bottom region of the deep drawn rectangular cup, was observed. This failure mode can be avoided by additional ironing thickness control during the process.

• Bulletin of the Korean Chemical Society
• /
• 제33권8호
• /
• pp.2523-2528
• /
• 2012

Green phosphors $(Zn_{1-a-b}M_aM^{\prime}_b)_xGa_yS_{x+3y/2}:Eu^{2+}$ (M, M' = alkali earth ions) with x = 2 and y = 2-5 were prepared, starting from ZnO, MgO, $SrCO_3$, $Ga_2O_3$, $Eu_2O_3$, and S with a flux $NH_4F$ using a conventional solidstate reaction. A phosphor with the composition of $(Zn_{0.6}Sr_{0.3}Mg_{0.1})_2Ga_2S_5:Eu^{2+}$ produced the strongest luminescence at a 460-nm excitation. The observed XRD patterns indicated that the optimized phosphor consisted of two components: zinc thiogallate and zinc sulfide. The characteristic green luminescence of the $ZnS:Eu^{2+}$ component on excitation at 460 nm was attributed to the donor-acceptor ($D_{ZnGa_2S_4}-A_{ZnS}$) recombination in the hybrid boundary. The optimized green phosphor converted 17.9% of the absorbed blue light into luminescence. For the fabrication of light-emitting diode (LED), the optimized phosphor was coated with MgO using magnesium nitrate to overcome their weakness against moisture. The MgO-coated green phosphor was fabricated with a blue GaN LED, and the chromaticity index of the phosphor-cast LED (pc-LED) was investigated as a function of the wt % of the optimized phosphor. White LEDs were fabricated by pasting the optimized green (G) and the red (R) phosphors, and the commercial yellow (Y) phosphor on the blue chips. The three-band pc-WLED resulted in improved color rendering index (CRI) and corrected color temperature (CCT), compared with those of the two-band pc-WLED.

• Journal of Ginseng Research
• /
• 제36권3호
• /
• pp.298-307
• /
• 2012

Panax ginseng has been cultivated for centuries, and nine commercial cultivars have been registered in Korea. However, these nine elite cultivars are grown in less than 10% of ginseng fields, and there is no clear authentication system for each cultivar even though their values are higher than those of local landraces. Here, we have developed 19 microsatellite markers using expressed gene sequences and established an authentication system for all nine cultivars. Five cultivars, 'Chunpoong', 'Sunpoong', 'Gumpoong', 'Sunun', and 'Sunone', can each be identified by one cultivar-unique allele, gm47n-a, gm47n-c, gm104-a, gm184-a (or gm129-a), and gm175-c, respectively. 'Yunpoong' can be identified by the co-appearance of gm47n-b and gm129-c. 'Sunhyang' can be distinguished from the other eight cultivars by the co-appearance of gm47n-b, gm129-b, and gm175-a. The two other cultivars, 'Gopoong' and 'Cheongsun', can be identified by their specific combinations of five marker alleles. This marker set was successfully utilized to identify the cultivars among 70 ginseng individuals and to select true F1 hybrid plants between two cultivars. We further analyzed the homogeneity of each cultivar and phylogenetic relationships among cultivars using these markers. This marker system will be useful to the seed industry and for breeding of ginseng.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권4호
• /
• pp.425-435
• /
• 2016

This paper describes a spread-spectrum clock generation method by utilizing a ${\Delta}{\Sigma}$ digital PLL (DPLL) which is solely based on binary phase detection and does not require a linear time-to-digital converter (TDC) or other linear digital-to-time converter (DTC) circuitry. A 1-bit high-order ${\Delta}{\Sigma}$ modulator and a hybrid finite-impulse response (FIR) filter are employed to mitigate the phase-folding problem caused by the nonlinearity of the bang-bang phase detector (BBPD). The ${\Delta}{\Sigma}$ DPLL employs a two-point modulation technique to further enhance linearity at the turning point of a triangular modulation profile. We also show that the two-point modulation is useful for the BBPLL to improve the spread-spectrum performance by suppressing the frequency deviation at the input of the BBPD, thus reducing the peak phase deviation. Based on the proposed architecture, a 3.2 GHz spread-spectrum clock generator (SSCG) is implemented in 65 nm CMOS. Experimental results show that the proposed SSCG achieves peak power reductions of 18.5 dB and 11 dB with 10 kHz and 100 kHz resolution bandwidths respectively, consuming 6.34 mW from a 1 V supply.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4102-4110
• /
• 2022

Aiming at high-power and long-pulse operation up to 1000 s, some improvements have been made for both 2.45 GHz and 4.6 GHz lower hybrid (LH) systems during the recent 5 years. At first, the guard limiters of the LH antennas with graphite tiles were upgraded to tungsten, the most promising material for plasma facing components in nuclear fusion devices. These new guard limiters can operate at a peak power density of 12.9 MW/m². Strong hot spots were usually observed on the old graphite limiters when 4.6 GHz system operated with power >2.0 MW [B. N. Wan et al., Nucl. Fusion 57 (2017) 102019], leading to a reduction of the maximum power capability. With the new limiters, 4.6 GHz LH system, the main current drive (CD) and electron heating tool for EAST, can be operated with power >2.5 MW routinely. Long-pulse operation up to 100 s with 4.6 GHz LH power of 2.4 MW was achieved in 2021 and the maximal temperature on the guard limiters measured by an infrared (IR) camera was about 540 ℃, much below the permissible value of tungsten material (~1200 ℃). A discharge with a duration of 1056 s was achieved and the 4.6 GHz LH energy injected into the plasma was up to 1.05 GJ. Secondly, the fully-active-multijunction (FAM) launcher of 2.45 GHz system was upgraded to a passive-active-multijunction (PAM), for which the density of optimum coupling was relatively low (below the cut-off value). Good coupling with reflection coefficient ~3% has been achieved with plasma-antenna distance up to 11 cm for the new PAM. Finally, in order to eliminate the effect of ion cyclotron range of frequencies (ICRF) wave on 4.6 GHz LH wave coupling, the location of the ICRF launcher was changed to a port that is located 157.5° toroidally from the 4.6 GHz LH system and is not magnetically connected.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2003년도 하계학술대회
• /
• pp.286-288
• /
• 2003

In this paper, in order to obtain a large differential phase shift with a little change in applied voltage, a ferroelectric reflective load circuit has been designed on top of barium strontium titanate $(Ba,Sr)TiO_3$ [BST] thin film. The design of the ferroelectric reflection-type phase shifter is based on a reflection theory of terminating circuit, which has a reflection-type analogue phase shifter with two ports terminated in symmetric phase-controllable reflective networks. To achieve large amounts of phase shift in low bias-voltage range, the effects of change of capacitance and transmission line connected with two coupled ports of a 3-dB $90^{\circ}$ branch-line hybrid coupler have been investigated. A large phase shift with a small capacitance change in the parallel terminating circuit has been demonstrated in the paper.

• Bulletin of the Korean Chemical Society
• /
• 제34권4호
• /
• pp.1043-1046
• /
• 2013

Prediction of physicochemical properties of organic molecules is an important process in chemistry and chemical engineering. The MSEP approach developed in our lab calculates the molecular surface electrostatic potential (ESP) on van der Waals (vdW) surfaces of molecules. This approach includes geometry optimization and frequency calculation using hybrid density functional theory, B3LYP, at the 6-31G(d) basis set to find minima on the potential energy surface, and is known to give satisfactory QSPR results for various properties of organic molecules. However, this MSEP method is not applicable to screen large database because geometry optimization and frequency calculation require considerable computing time. To develop a fast but yet reliable approach, we have re-examined our previous work on organic molecules using two semi-empirical methods, AM1 and PM3. This new approach can be an efficient protocol in designing new molecules with improved properties.

• 원예과학기술지
• /
• 제30권2호
• /
• pp.224-228
• /
• 2012

분화용 바위떡풀 신품종 '크리스탈(Crystal)'은 꽃색이 연녹색 바탕에 연한 핑크색을 나타내는 품종인 '도태랑'을 모본으로 하고 역시 화색이 유사한 '록선' 품종을 부본으로 하여 2004년에 인공 교배하여 선발한 계통으로부터 육성하였다. 2005-2007년까지 3년에 걸쳐 생육 및 개화특성을 검정한 후 최종적으로 선정하여 '크리스탈(Crystal)'로 명명하였다. '크리스탈' 품종의 개화는 9월 21일부터 시작하여 10월 하순까지 약 31일간 피며 꽃 수는 279개로 많고 화경수도 11.2개로 많았으며 화경장은 15.3cm로 작아 전체적으로는 안정적인 초형이었다. 화색은 연한 녹색 바탕에 밝은 핑크색(R-P 62D + G-W 157B)을 띠며 화장 1.8cm, 화폭이 2.1cm로 작은 편이고 꽃잎 수는 7.0개로 비대(大)자형을 이루며 엽장은 3.5cm, 엽폭은 3.8cm의 크기였고 엽수는 133.7개로 많았다.

• 대한화장품학회지
• /
• 제30권2호
• /
• pp.181-187
• /
• 2004

화장품에서 유기 화합물인 OMC(octyl methoxy cinnamate)와 무기 소재인 TiO$_2$가 자외선 차단제로 가장 보편적으로 사용되고 있다. 그러나 OMC는 skin trouble이 있고, TiO$_2$는 첨가량에 비해서 자외선 차단 효율이 OMC보다 낮고 입자의 크기효과에 의해 백탁 현상이 나타나는 단점이 있다. 본 연구에서는 이러한 두 성분이 갖는 단점을 보완하는 방법으로 OMC를 나노에멀젼시키고, 이 나노에멀젼-OMC를 나노-TiO$_2$ 미립자로 포접하여 자외선 차단효과를 극대화 하면서, 피부에 OMC가 직접적으로 적용하지 못하도록 하는 방법을 연구하였다. 특히 계면활성제를 boundary로 하는 유기/무기 hybrid nano-material에서 TiO$_2$ 미립자와 OMC-에멀젼이 나노 크기가 되면 백탁 현상이 나타나지 않는 투명한 화장품을 제조할 수 있을 뿐만 아니라 나노-에멀젼 OMC를 TiO$_2$로 포집하는 과정에서 hydrophilic character를 갖는 레시친으로 TiO$_2$를 안정화하여 보습성을 더욱 향상시켰다. 합성한 inorganic-organic hybrid nano-material는 TEM을 이용하여 나노 미립자의 morphologies를 규명하였고, UV-Visible spectrometer를 이용하여 자외선 흡수를 측정하였다. 또한 X-ray diffractometer를 이용하여 나노-에멀젼 OMC를 포집하고 있는 TiO$_2$ 미립자가 갖는 특성인 pore의 크기와 구조를 측정하였다. 화장품적인 응용으로서 SPF analyzer 측정결과 기존의 powder-OMC에 비하여 우수한 자외선 차단 효과를 나타내었으며, OMC의 피부 침투도 훨씬 줄일 수 있어 OMC의 피부 부작용을 크게 줄일 수 있을 것이다.>$\pm$0.06 $\mu$g/g 범위였다. 4. 날결명자 분말첨가군 각 조직에 축적된 카드뮴 함량이 제일 낮았던 C4를 Cl과 비교한 결과 뇌, 심장, 비장, 간, 폐, 고환, 신장, 대퇴부근육, 다리뼈에 각각 49.03, 22.56, 36.02, 35.75, 41.75, 36.20, 37.00, 22.77, 56.67 %의 감소를 보였으며, 각 장기의 함량은 뇌<다리뼈<대퇴부 근육<고환<폐<심장<비장<신장<간 순 이었다. 5. 카드뮴 총 섭취량으로 장기 및 조직의 카드뮴 평균함량에 대한 축적율은 카드뮴만 섭취한 군(Cl) 의 경우 7.14%이었으며, 결명자 분말 첨가군인 C2, C3, C4군의 경우 각각 4.91, 4.81, 4.50 %이었다. 6. 체모의 카드뮴 함량은 Cl군이 가장 높았고, 결명자 첨가군들의 카드뮴 함량은 6주째까지 모든 시험군에서 증가하는 경향을 보였으며, 6주 이후에는 감소되는 경향을 보였다. 7. 분변 중 카드뮴 함량은 C4군이 가장 높았고, 결명자 첨가군들의 카드뮴 함량은 C3군과 C4군을 제외한 나머지 군들에서 완만하게 증가하는 경향을 보였으며, 6주째에 카드뮴 함량이 감소되는 경향을 보였다가 6주 이후에 다시 카드뮴 함량이 증가하는 경향이었다.erefore the guidelines for iron supplementation and nutritional education to improve their iron status should be provided.한 질소제거를 N-balance로부터 구해보면, R3 반응조의 경우가 가장 높은 제거율(40.9%)을 보였다. 이상의 결과들을 볼 때, Bncillus 균주는 호기적 탈질을 일으킬 수 있는 가능성이 있고, Bncillus 균주를 이용한 B3 공정은 탈질에 이용되는 탄소량이 거의 없고, 적은 alkalinity 소모에 의한 경제적 이익 등 장점을 가진 공정으로 보여 진다.수록 푹신한 감이 있는

• Asian-Australasian Journal of Animal Sciences
• /
• 제17권10호
• /
• pp.1344-1349
• /
• 2004

Titin-cap (TCAP), one of the abundant transcripts in skeletal muscles, was nvestigated in this study in cattle because of its role in regulating the proliferation and differentiation of myoblasts by interacting with the myostatin gene. From the 5, and 3, RACE experiments, full-length TCAP coding sequence was identified, comprising 166 amino acids. The amino acid comparison showed high sequence similarities with previously identified human (95.8%) and mouse (95.2%) TCAP genes. The TCAP expression, addressed by northern blot, is limited in muscle tissues as indicated by Valle et al. (1997). The radiation hybrid analysis localized the gene on BTA19, where the comparative human and porcine counterparts are on HSA17 and SSC12. A few muscle-related genetic disorders were mapped on HSA17 and some growth-related QTLs were identified on SSC12. The bovine TCAP gene found in this study opens up new possibilities for the investigation of muscle-related genetic diseases as well as meat yield traits in cattle.