• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.35-40
• /
• 2019

In this study, the mass flow rate of the heat release rate equation, which is the major factor of the oxygen consumption method, was analyzed for the fundamental investigation of the cone-calorimeter (5 m length and 0.3 m diameter). The shapes of a completely empty inside, 3 mm pore diameter mesh and pore diameter 10 mm honeycomb with 0.76 porosity were constructed using the cone-calorimeter. To calculate the mass flow rate, four bi-directional probes and thermocouples were installed in a uniform position in the vertical direction of flow. The velocity gradient and flow perturbation were measured from the increase in Reynolds number. As the flow capacity increased, the speed gradient increased in all three shapes relative to the turbulence intensity. In addition, the deviation of extended uncertainty to the mass flow was completely low in the order of empty space, mesh (d_p = 3 mm) and honeycomb (d_p = 10 mm and 𝜖 = 0.76) at the 95% confidence level. The results can be used in designs to improve the flow stability of the cone calorimeter.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2018.04a
• /
• pp.54-54
• /
• 2018

억새(Miscanthus spp.)는 우리나라 등 동아시아가 원산이며 바이오매스량이 많아 바이오에너지 원료작물로서 잠재성이 크기 때문에 2세대 바이오에탄올 생산 원료로 주목을 받고 있고, 축산깔개 및 토양개량제 등으로도 이용되고 있다. 미국과 유럽 등에서는 생태계 교란 방지를 위해 4배체 물억새(M. sacchariflorus)와 2배체 참억새(M. sinensis)의 종간 교잡 이질 3배체인 불임성 억새(M. x giganteous)을 주로 재배하고 있으나, 단일 유전형의 품종으로 병해충과 자연재해에 취약하여 다양한 억새 품종의 개발이 시급한 실정이다. 본 연구는 억새를 재료로 하여 반수체 및 배수체 확보를 통한 배수성 별 특성 평가와 함께 기내배양을 통해 탈분화 및 재분화 시스템을 구축하여 억새의 육종 효율을 높이기 위해서 실시하였다. 억새 종자로부터 캘러스의 유도는 MS배지와 N6배지에 1mg/L 2.4-D를 첨가하였을 때 비배발생 캘러스(nonembryogenic callus)가 유도되었고, N6배지에 3~5 mg/L 2,4-D를 첨가하였을 때 배발생 캘러스(embryogenic callus)가 발생하였다. MS배지보다는 N6배지에서 캘러스 유도율이 높았으며, 식물생장조절제로 2,4-D와 BA 조합처리 보다 2,4-D 단용 처리하였을 때 캘러스 유도율이 더 높았다. 억새 종에 따른 캘러스 유도율은 물억새가 25.2~49.3%, 참억새는 30.3~52.0%였고 거대억새는 62.6~81.1%로 나타났다. 억새 신초 및 줄기로부터의 캘러스 유도율은 물억새가 4.4~17.2%, 참억새는 1.8~7.7%, 거대억새는 15.3~19.9%로 나타나 종자에 비해 매우 낮았다. 미성숙화기로부터의 캘러스 유도는 억새 종에 따른 차이가 없었으며, 3mg/L 2,4-D 첨가 배지에서 캘러스 유도율이 비교적 낮았고(60~80%), 1mg/L와 5mg/L의 2,4-D가 첨가된 배지에서 캘러스 유도율이 높게(90~95%) 나타났다.

• Korean Journal of Remote Sensing
• /
• v.31 no.3
• /
• pp.215-226
• /
• 2015

Normally, aero photography using UAV uses about 430 MHz bandwidth radio frequency (RF) modem and navigates and remotely controls through the connection between UAV and ground control system. When using the exhausting method, it has communication range of 1-2 km with frequent cross line and since wireless communication sends information using radio wave as a carrier, it has 10 mW of signal strength limitation which gave restraints on life my distance communication. The purpose of research is to use communication technologies such as long-term evolution (LTE) of smart camera, Bluetooth, Wi-Fi and other communication modules and cameras that can transfer data to design and develop automatic shooting system that acquires images to UAV at the necessary locations. We conclude that the android based UAV filming and communication module system can not only film images with just one smart camera but also connects UAV system and ground control system together and also able to obtain real-time 3D location information and 3D position information using UAV system, GPS, a gyroscope, an accelerometer, and magnetic measuring sensor which will allow us to use real-time position of the UAV and correction work through aerial triangulation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.3
• /
• pp.503-515
• /
• 2017

Underground structures that have recently become larger are required to be stable not only during normal times but also during earthquakes. Especially, it is very important to maintain the stability of the subsea tunnels during the earthquake. The objective of this paper is to verify the effectiveness of the flexible segment, which is one of the breakthrough facilities to maintain the stability of the subsea tunnel during the earthquake using the shaking table test. Another goal of this paper is to propose the optimum position of the flexible segment through 3D dynamic numerical analysis based on the verified results from shaking table tests. The 1g shaking table test considering the similarity ratio (1:100) to the cross section of the selected artificial subsea tunnel was carried out considering the Geongju and Artificial seismic waves, longitudinal and lateral wave, and with/without flexible segments eight times or more. As a result of the shaking table test, it was confirmed that the flexible segment is effective in improving the seismic performance of the undersea tunnel in all the experimental results. In addition, 3D dynamic numerical analysis was performed to select the optimum position of the flexible segment which is effective for improving seismic performance. As a result, it was confirmed that the seismic acceleration is attenuated when the flexible segment is installed adjacent to the branch section in subsea tunnel.

• The Journal of Korean Society for Radiation Therapy
• /
• v.31 no.1
• /
• pp.57-65
• /
• 2019

Purpose: The purpose is to clarify the effect of additional scattering ratio on the edge of the block according to the increasing block thickness with low melting point lead alloy and pure lead in electron beam therapy. Methods and materials: $10{\times}10cm^2$ Shielding blocks made of low melting point lead alloy and pure lead were fabricated to shield mold frame half of applicator. Block thickness was 3, 5, 10, 15, 20 (mm) for each material. The common irradiation conditions were set at 6 MeV energy, 300 MU / Min dose rate, gantry angle of $0^{\circ}$, and dose of 100 MU. The relative scattering ratio with increasing block thickness was measured with a parallel plate type ion chamber(Exradin P11) and phantom(RW3) by varying the position of the shielding block(cone and on the phantom), the position of the measuring point(surface ans depth of $D_{max}$), and the block material(lead alloy and pure lead). Results : When (depth of measurement / block position / block material) was (surface / applicator / pure lead), the relative value(scattering ratio) was 15.33 nC(+0.33 %), 15.28 nC(0 %), 15.08 nC(-1.31 %), 15.05 nC(-1.51 %), 15.07 nC(-1.37 %) as the block thickness increased in order of 3, 5, 10, 15, 20 (mm) respectively. When it was (surface / applicator / alloy lead), the relative value(scattering ratio) was 15.19 nC(-0.59 %), 15.25 nC(-0.20 %), 15.15 nC(-0.85 %), 14.96 nC(-2.09 %), 15.15 nC(-0.85 %) respectively. When it was (surface / phantom / pure lead), the relative value(scattering ratio) was 15.62 nC(+2.23 %), 15.59 nC(+2.03 %), 15.53 nC(+1.67 %), 15.48 nC(+1.31 %), 15.34 nC(+0.39 %) respectively. When it was (surface / phantom / alloy lead), the relative value(scattering ratio) was 15.56 nC(+1.83 %), 15.55 nC(+1.77 %), 15.51 nC(+1.51 %), 15.42 nC(+0.92 %), 15.39 nC(+0.72 %) respectively. When it was (depth of $D_{max}$ / applicator / pure lead), the relative value(scattering ratio) was 16.70 nC(-10.87 %), 16.84 nC(-10.12 %), 16.72 nC(-10.78 %), 16.88 nC(-9.93 %), 16.90 nC(-9.82 %) respectively. When it was (depth of $D_{max}$ / applicator / alloy lead), the relative value(scattering ratio) was 16.83 nC(-10.19 %), 17.12 nC(-8.64 %), 16.89 nC(-9.87 %), 16.77 nC(-10.51 %), 16.52 nC(-11.85 %) respectively. When it was (depth of $D_{max}$ / phantom / pure lead), the relative value(scattering ratio) was 17.41 nC(-7.10 %), 17.45 nC(-6.88 %), 17.34 nC(-7.47 %), 17.42 nC(-7.04 %), 17.25 nC(-7.95 %) respectively. When it was (depth of $D_{max}$ / phantom / alloy lead), the relative value(scattering ratio) was 17.45 nC(-6.88 %), 17.44 nC(-6.94 %), 17.47 nC(-6.78 %), 17.43 nC(-6.99 %), 17.35 nC(-7.42 %) respectively. Conclusions: When performing electron therapy using a shielding block, the block position should be inserted applicator rather than the patient's body surface. The block thickness should be made to the minimum appropriate shielding thickness of each corresponding using energy. Also it is useful that the treatment should be performed considering the influence of scattering dose varying with distance from the edge of block.

• The Journal of Korean Society for Radiation Therapy
• /
• v.22 no.2
• /
• pp.135-144
• /
• 2010

Purpose: The purpose of this study is that through production of phantom for respiration gated radiotherapy, assessing appropriacy of exposure dose for the therapy using RPM (Real-time Position Management). Materials and Methods: We located measurement object on the phantom for respiration gated radiotherapy made of 2 linear actuator, acrylic panel, stanchion, iron plate ets. to drive (up, down, front, back). Using 4D CT scan, we analyzed patient's respiration and reproduced the movement by computer. On the phantom, we located a 2D-Array (PTW) and an White water phantom (4.5 cm) and used DMLC (interval 2 cm) in the field size $10{\times}10\;cm$, then exposed 21EX X-ray 100 MU, in the case of phantom was (1) static (2) moving (3) gated using RPM respectively gantry $0^{\circ}$ and $90^{\circ}$ We measured with a 0.125 CC ionization chamber (PTW) on the phantom (7.5 cm) in the same condition. Results: Ionization chamber: There were within 0.3% of error with gating respiration and approximately 2% of error without gating in the same condition. 2D-Array: Gantry $90^{\circ}$, field size $10{\times}10\;cm$, using DMLC. There were within 3% of error with gating respiration and approximately 16% of error without gating. Conclusion: The phantom for respiration gated radiotherapy makes plans considering patient's movement, quantitative analysis of exposure dose and proper assessment therapy for IMRT patients using RPM possible.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.40 no.4
• /
• pp.260-267
• /
• 2013

The aim of this study was to analyze the three dimensional characteristics of the size, shape and location of mesiodens and their effect on permanent teeth arrangement using Cone-beam computed tomography(CBCT). 191 patients under 15 years old who had visited the hospital between June 2006 and December 2012 and taken CBCT were investigated. Among them, 43 patients with diastema were analyzed to investigate the correlation between the amount of diastema and the mesiodens. The results showed that mesiodens were found in males 3.9 times more than females and found most in 7 years old. The mean length of mesiodens was 13 mm and the width was 6.8 mm. The conical shape comprised of 52.9%. Many mesiodens were located in the palatal side rather than the labial side and located vertically near the crown. 63.0% of mesiodens were reversed and the common complications were delayed eruption followed by diastema, and teeth rotation. And the amount of diastema had correlation with size and mesiodistal position of the mesiodens. The current study used 3D analysis to show the size and position of mesiodens and occurrence distribution of complication. Among these, the amount of diastema had shown the correlation with the size and mesiodistal position of mesiodens.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8A
• /
• pp.712-719
• /
• 2012

This paper presents Single-bit Third order Delta-Sigma Modulator, which can be applied to the Low speed High resolution ADC in Audio signal Process System. Whereas the Operational Amplifier in modulator consumed static power dissipation in operating, this modulator used Switching on/off techniques, which makes the Power dissipation of the modulator reduced. Also proposed modulator minimizes frequency characteristic variation by optimizing switch position. And this modulator chooses Single-bit type to guarantee stability. The designed ADC went through 0.35um CMOS n-well 1-poly 4-metal process to be a final product, and the final product has shown 17.1mW of power dissipation with 3.3V of Supply Voltage, 6.4MHz of conversion rate. And 84.3dB SNDR and 13.5bit ENOB with 20KHz of input frequency.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.11
• /
• pp.3335-3339
• /
• 2013

Boron-doped ZnO (BZO) nanorods were grown on quartz substrates using hydrothermal synthesis, and the temperature-dependence of their photoluminescence (PL) was measured in order to investigate the origins of their PL properties. In the UV range, near-band-edge emission (NBE) was observed from 3.1 to 3.4 eV; this was attributed to various transitions including recombination of free excitons and their longitudinal optical (LO) phonon replicas, and donor-acceptor pair (DAP) recombination, depending on the local lattice configuration and the presence of defects. At a temperature of 12 K, the NBE produces seven peaks at 3.386, 3.368, 3.337, 3.296, 3.258, 3.184, and 3.106 eV. These peaks are, respectively, assigned to free excitons (FX), neutral-donor bound excitons ($D^{\circ}X$), and the first LO phonon replicas of $D^{\circ}X$, DAP, DAP-1LO, DAP-2LO, and DAP-3LO. The peak position of the FX and DAP were also fitted to Varshni's empirical formula for the variation in the band gap energy with temperature. The activation energy of FX was about ~70 meV, while that of DAP was about ~38 meV. We also discuss the low temperature PL near 2.251 eV, related to structural defects.

• PNF and Movement
• /
• v.16 no.3
• /
• pp.485-493
• /
• 2018

Purpose: This study provides a treatment for central nervous system development in patients with chronic stroke by investigating changes in the upper limb function over time. The correlations among the activities, participation, and environmental factors of the international classification of functioning (ICF), disability and health are also examined. Methods: The subjects of this study are 18 patients with chronic stroke who were hospitalized and treated at 00 hospital in the Chungcheongbuk-do province. Their upper extremity functions are evaluated using the manual function test (MFT). The activities, participation, and environmental factors are evaluated using the ICF generic form. The correlations between the total scores of the affected and unaffected sides and the ICF items are analyzed using the Pearson correlation analysis. The significance level is p<0.05. Results: When the correlations between the activities and participation areas of ICF and the total score of the affected side of MFT were examined, significant correlations (p<0.05) were found in the following items: changing basic body position (D410), lifting and carrying objects (D430), moving around using equipment (D465), using transportation (D470), washing oneself (D510), caring for body parts (D520), and dressing (D540). When the correlations between the activities and participation areas of ICF and the total score of the unaffected side of MFT were examined, significant correlations (p<0.05) were found among writing (D170), speaking (D330), eating (D550), and drinking (D560). In addition, when the correlation between the environment area of ICF and the total score of the unaffected side of the MFT were examined, significant correlations (p<0.05) were found between products and technology for personal use in daily living (E115) and immediate family (E310). Conclusion: The MFT of patients with chronic stroke is closely correlated with the activities, participation, and environmental factors of ICF. This result suggests that ICF can be used as a useful tool to comprehensively evaluate the abilities of the patient, including the upper extremity function.