• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.15-20
• /
• 2011

This study was conducted to evaluate the characteristics of installation dimensions of speed control humps based on the theoretical dynamic analyses. The field surveys of speed control humps were performed first to compare their sizes with those suggested in the installation standard. Then, the displacement response spectra under impact loads were obtained using the single degree of freedom models where the vehicle and human were assumed to combine completely. The analysis results showed that the human perception became larger as the width and height of the humps increased, but the extremely higher uncomfortableness should be avoided. In addition, the ratio between the width and height should be considered when the humps are designed and installed because the ratio governs the vertical acceleration magnitude.

• Wind and Structures
• /
• v.37 no.1
• /
• pp.57-78
• /
• 2023

In this study, a generalized three-degree-of-freedom (3-DoF) analytical model is formulated to predict linear aerodynamic instabilities of a prism under quasi-steady (QS) conditions. The prism is assumed to possess a generic cross-section exposed to turbulent wind flow. The 3-DoFs encompass two orthogonal horizontal directions and rotation about the prism body axis. Inertial coupling is considered to account for the non-coincidence of the mass center and the rotation center. The aerodynamic force coefficients-drag, lift, and moment-depend on the Reynolds number based on relative flow velocity, angle of attack, and the angle between the wind and the cable. Aerodynamic forces are linearized with respect to the static equilibrium configuration and mean wind velocity. Routh-Hurwitz and Liénard and Chipart criteria are used in the eigenvalue problem, yielding an analytical solution for instabilities in galloping and static divergence types. Additionally, the minimum structural damping and stiffness required to prevent these instabilities are numerically determined. The proposed 3-DoF instability model is subsequently applied to a conductor with ice accretion and a full-scale dry inclined cable. In comparison to existing models, the developed model demonstrates superior prediction accuracy for unstable regions compared with results in wind tunnel tests.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1667-1672
• /
• 2009

The spherical motor is an electric machine which is able to tilt its shaft on 3-dimensional space as using electromagnetic force. Recently a permanent magnet is remarkable material for applying electric machinery, because of high magnetic flux density. In this paper, a spherical motor, which has permanent magnet on its rotor, is researched. As known, the spherical motor has a special feature as 3 degrees of freedom (D.O.F) operation. This performance can be realized by using electromagnetic torque between coils and magnets. Therefore, in this paper, a permanent magnet spherical wheel motor is introduced and performance characteristics are analyzed for improving of operation stability.

• Journal of Broadcast Engineering
• /
• v.24 no.6
• /
• pp.1035-1052
• /
• 2019

Recently, as the demand for immersive videos increases, efficient video processing techniques for omnidirectional immersive video is actively developed by MPEG-I. While the omnidirectional video provides a larger degree of freedom for a free viewpoint, the size of the video increases significantly. Furthermore, in order to compress 6 degree-of-freedom (6 DoF) videos that support motion parallax, it is required to develop a codec to yield better coding efficiency. In this paper, we develop a 6 DoF codec using Versatile Video Coding (VVC) as the next generation video coding standard. To the authors' best knowledge, this is the first VVC-based 6 DoF video codec toward the future ISO/IEC 23090 Part 7 (Metadata for Immersive Media (Video)) MPEG-I standardization. The experiments were conducted on the seven test video sequences specified in Common Test Condition (CTC) in two operation modes of TMIV (Test Model for Immersive Media) software. It is demonstrated that the proposed codec improves coding performance around 33.8% BD-rate reduction in the MIV (Metadata for Immersive Video) mode and 30.2% BD-rate reduction in the MIV view mode as compared to the state-of-the-art TMIV reference software. We also show the performance comparisons using Immersive Video PSNR (IV-PSNR) and Mean Structural Similarity (MSSIM).

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.3 s.73
• /
• pp.223-231
• /
• 2006

This study deals with behavior characteristics of laminated composite folded structures according to ratio of folded length based on a higher-order shear deformation theory. Well-known mixed finite element method using Lagrangian and Hermite shape interpolation functions is a little complex and have some difficulties applying to a triangular element. However, a higher-order shear deformation theory using only Lagrangian shape interpolation functions avoids those problems. In this paper, a drilling degree of freedom is appended for more accurate analysis and computational simplicity of folded plates. There are ten degrees of freedom per node, and four nodes per element. Journal on folded plates for effects of length variations is not expressed. Many results in this study are carried out according to ratio of folded length. The rational design is possible through analyses of complex and unpredictable laminated composite folded structures.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.3
• /
• pp.161-163
• /
• 2014

We consider the device-to-device (D2D) communication underlaying multi-cell interference system, in which the cellular downlink (DL) resource is reused by K cells and two D2D transmission links within each cell. In this paper, it has been shown that the downlink intra-cell and inter-cell interference can be effectively handled by interference alignment (IA) technique, as long as the simultaneous D2D links are properly selected or power-controlled so that they may not incur interference to the base stations in the same and neighbor cells. In particular, we provides the IA technique that can achieve the theoretically maximum possible degree of freedom (DOF), demonstrating that a total of (K+1)M degrees of freedom (DOFs) can be achieved for K-cell interference system with two underlaying D2D links, where base stations, cellular UE's, and D2D UE's all have M transmit and receive antennas.

• Structural Engineering and Mechanics
• /
• v.49 no.3
• /
• pp.329-353
• /
• 2014

Increasing usage of tank cars and their intrinsic instability due to sloshing of contents have caused growing maintenance costs as well as more frequent hazards and defects like derailment and fatigue of bogies and axels. Therefore, varieties of passive solutions have been represented to improve dynamical parameters. In this task, assuming 22 degrees of freedom, dynamic analysis of partially filled tank car traveling on a curved track is investigated. In order to consider stochastic geometry of track; irregularities have been derived randomly by Mont Carlo method. More over the fluid tank model with 1 degree of freedom is also presented by equivalent mechanical approach in terms of pendulum. An active suspension system for described car is designed by using linear quadratic optimal control theory to decrease destructive effects of fluid sloshing. Eventually, the performance of the active suspension system has been compared with that of the passive one and a study is carried out on how active suspension may affect the dynamical parameters such as displacements and Nadal's derailment index.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.2
• /
• pp.118-126
• /
• 2014

In this paper, a new method is proposed for the five-degree-of-freedom precision alignment and stitching of three-dimensional surface-profile data sets. The control parameters for correcting thealignment error are calculated from the surface profile data for overlapped areas among the adjacent measuring areas by using the "least squares method" and "maximum lag position of cross correlation function." To ensure the alignment and stitching reliability, the relationships betweenthe alignment uncertainty, overlapped area, and signal-to-noise level of the measured profile data are investigated. Based on the results of this uncertainty analysis, an appropriate size is proposed for the overlapped area according to the specimen's surface texture and noise level.

• Smart Structures and Systems
• /
• v.7 no.3
• /
• pp.169-184
• /
• 2011

We review the current understanding of modularity in biological motor control and its forms, and then relate this modularity to proposed modular control structures for biomimetic robots. We note the features that are different between the robotic and the biological 'designs' with features which have evolved by natural selection, and note those aspects of biology which may be counter-intuitive or unique to the biological controls as we currently understand them. Biological modularity can be divided into kinematic modularity comprised of strokes and cycles: primitives approximating a range of optimization criteria, and execution modularity comprised of kinetic motor primitives: muscle synergies recruited by premotor drives which are most often pulsatile, and which have the biomechanical effect of instantiating a visco-elastic force-field in the limb. The relations of these identified biological elements to kinematic and force-level motor primitives employed in robot control formulations are discussed.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.823-824
• /
• 2006

This paper proposes a novel structured 3-DOF(Degree-of-Freedom) spherical motor. 3-DOF spherical motor presents some attractive features by combining pitch, roll, yaw motion in a single joint. The proposed motor has pole which is electromagnetic in stator and rotor. poles produce magnetic flux through by exciting current then produce torque. We show a novel structured rotor to avoid mechanical overlapping of each coil in rotor. The validity of the analysis is confirmed by 3D finite element method.