• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.2
• /
• pp.16-21
• /
• 1993

A newly advanced method of characterizing large signal S-parameters of TR using the overall gain of normally operating TR is proposed based on the load pull method which gives the matching network only. Large signal S-parameters of TR are characterized from the circuit which consists of TR and 3dB Coupler Tuners at the input and output ports, and which is B class biased with 0dBminput signal. Amplifier can be designed to have 8.5dB gain at 770MHz using the calculated large signal S-parameters with the resulting gain of 8.786dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2016

In this paper, the tunable filter based on high power cavity using mechanical switch for 1.5 GHz band is presented. The LPF is inserted to eliminate the spurious wave, coupler is embeded to extract the output power, and then the tunable filter system is configured using mechanical switch. The LPF obtains attenuation over 40 dB between 4 GHz and 12.75 GHz, Coupler is satisfied with coupling value 40 dB and coupling isolation over 55 dB. The tunable filter system using mechanical switch obtains insertion loss 0.88 dB at bypass mode between 1,495.9 MHz and 1,510. 9 MHz, 3.29 dB at fil mode between 1,495.9 MHz and 1,500.9 MHz. It is also satisfied with output power of 132 W at the center frequency 1,498.4 MHz, and switching time below 10 ms.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.94-100
• /
• 2002

In this paper, we proposed a 3 dB coupler using N-section parallel-coupled lines and designed a very compact one based on the analysis results. The coupled line has been analyzed by spectral domain method. After we obtain the s-parameters of N-section parallel-coupled lines by using port reduction method 4-port s-parameters are derived. The 3 dB couplers, which were fabricated, are not necessary to implement high impedance lines and tight coupling gaps as Lange Couplers because loose coupling is used. To realize a minimum section, we used the PCB that has high a dielectric constant and a thickness. The experimental results show that it has wide bandwidth of about 42 %(0.5 dB unbalance) from 3.6 GHz to 5.5 GHz and phase difference within 1 degree. Also, The isolation characteristics about 15 dB at its pass-band are obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.688-693
• /
• 1999

This paper presents a very simple coupled line structure for MMIC which uses stacked microstrip line and does not employ any dielectric process step. For the analysis and optimization of these coupled line structure, HP-Momentum was used. The measured performance of 3 dB coupler shows 23 to 45 GHz broadband characteristics. Additionally, a balanced 2-stage Ka-Band power amplifier which uses the proposed 3 dB coupler, was also fabricated.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.11-16
• /
• 2014

In this paper, we proposed and demonstrated $1{\times}7$ type plastic optical fiber(POF) coupler incorporating a tapered acrylic cylinder which works optical combining and dividing region. A fabricated POF coupler showd 2.27~3.31 dB of insertion loss for optical combining and 8.67~11.27dB of insertion loss for optical spitting.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.41-48
• /
• 2005

We design and fabricate 3-dB tandem directional coupler using the coplanar waveguide structure which is applicable to balanced amplifiers and mixers for 60 GHz wireless local area network system. The coupler comprises the multiple-sectional parallel-coupled lines to facilitate the fabrication process, and enable smaller device size and higher directivity than those of the conventional 3-dB coupler employing the edge-coupled line. In this study, we adopt the structure of two-sectional parallel-coupled lines of which each single-coupled line has a coupling coefficient of -8.34 dB and airbridge structure to monolithically materialize the uniplanar coupler structure instead of using the conventional multilayer or bonded structure. The airbridge structure also supports to minimize the parasitic components and maintain desirable device performance in V-band (50$\~$75 GHz). The measured results from the fabricated couplers show couplings of 3.S$\~$4 dB and phase differences of 87.5$^{\circ}{\pm}1^{\circ}$ in V-band range and show directivities higher than 30 dB at a frequency of 60 GHz.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.9
• /
• pp.685-691
• /
• 1991

A broad-band 3-dB directional coupler is implemented by using cascaded exponential transmission line as branch lines. Compared with that of the uniform transmission line, the bandwidth of the proposed 3-dB branch-line directional cpoupler increases 2.96 times.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.1
• /
• pp.47-52
• /
• 2011

In this paper, to evaluate the design properties of 3D optical multimode interference (MMI) couplers with ultracompact width, modal transmission line theory and effective dielectric method are combined with together. A coupling efficiency based on the composed approach is defined, and the coupling length is numerically determined for the design of 3 dB coupler, cross coupler and bar coupler. The simulation result shows that the designed MMI coupler has a low insertion loss and a high splitting ratio.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.10
• /
• pp.1036-1043
• /
• 2003

In this paper, novel lumped equivalent circuits for a conventional parallel directional coupler are proposed. This novel equivalent circuits only have self inductance and self capacitance, so we can design exact lumped equivalent circuit. The equivalent circuit and design formula for the presented lumped element coupler is derived based on the even- and odd-mode properties of a parallel-coupled line. By using the derived design formula, we have designed the 3 dB and 10 dB lumped element directional couplers at the center frequency of 100 MHz and 2 GHz, respectively a chip type directional coupler has been designed with multilayer configurations by employing commercial EM simulator. Designed chip-type directional couplers have a 3 dB-coupling value at the center frequency of 2 GHz and fabricated lumped directional coupler on fr4 organic substrate has a 3 dB, 10 dB-coupling values at the center frequency of 100 MHz. Excellent agreements between simulation results and measurement results on the designed directional couplers show the validity of this paper. Furthermore, in order to adapt to multi-layer process such as Low Temperature Cofired Ceramic (LTCC), chip-type lumped element couplers have been designed by using this method.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.2
• /
• pp.13-18
• /
• 1998

In this paper, a new type microstrip directional coupler has been designed and a 3dB coupler has been fabricated and measured. The measured and analysed results are agree well each other except difference of 1 dB insertion loss. There are two eigenmodes, e.g. even and odd mode in coupled microstrip lines. By using the difference between these two eigenmodes phase constants, the directional coupler can be designed by adjusting coupling length, which has a desired coupler has a disdvantage that its coupling length is longer than conventional oe, but it may be used as a useful coupler in millimeter wave range. And it has the merit of less discontinuity effects, becuase it is simpler than the other couplers in structure.