• Annual Conference of KIPS
• /
• 2003.05a
• /
• pp.393-396
• /
• 2003

삼각형 스트립은 삼각형 메쉬에 대한 간결한 표현을 제공하는 데이터 구조이다 스킵 스트립은 실시간으로 삼각형 스트립을 이용하여 3차원 모델을 다해상도로 표현하는 효율적인 방법이다. 그렇지만 스킵 스트립은 모델이 점점 단순화될수록 삼각형 스트립의 과정에서 동일한 정점이 여러 번 축적된다. 이 정접들은 렌더렁에 불필요한 정점의 수를 증가시키는 퇴화 삼각형을 만들게 된다. 본 논문에서는 이러한 퇴화된 삼각형을 줄이기 위해서 퇴화 삼각형 제거 필터를 제안하며, 실험결과 단순 삼각형 스트립 스캐너의 방법보다 평균 22.2%의 정점 감소 효과를 얻을 수 있었다.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2017.11a
• /
• pp.343-344
• /
• 2017

우리나라는 산악지형 특성상 붕적층이 발달한 지역이 많아 도로나 건축물이 계획될 경우 일반적으로 이러한 지역을 배제하는 계획을 수립하게 된다. 그러나 현장 여건상 불가피하게 붕적층 구간을 포함한 건설 계획이 수립될 경우 지반 굴착, 사면 절취로 인해 지반 거동특성이 불안정할 수 있으므로 상세한 사전 조사와 적절한 토공 및 굴착 계획과 시공 중 Feed Back 등이 면밀히 이루어져야 한다. 붕적층 지반은 소량의 토사에 자갈, 호박돌, 전석 등이 혼재되어 있는 상태로 주로 테일러스에 의해 생성되며, 암괴의 함량이 매우 높으며 소량의 풍화된 잔류토사가 혼재된 양상을 보인다. 본 연구에서는 붕적층이 깊게 분포하는 지역, 특히 배면에 지장물(상수도관 등)문제로 인해 발생한 가시설 붕괴지역을 사례로 역해석을 통한 붕적층의 지반정수 재평가를 실시하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.05a
• /
• pp.216-221
• /
• 1998

슈퍼임포즈는 개인식별 방법으로 신원 미상의 두개골의 발견 시, 두개골의 사진과 용의자 생전 사진의 동일 비율로 확대, 축소 후 두 영상을 중첩하므로서 동일인 여부를 비교, 판별하는 기법이다. 삼풍백화점 붕괴사고와 Guam KAL기 추락사고와 같이 대형사건에서의 개인식별에 매우 중요한 문제이다. 본 연구는 비디오 카메라로 입력한 두개골 영상과 스캐너로 입력한 생전 사진의 중첩을 위한 H/W 시스템의 구축과 영상처리 기법을 응용한 응용 프로그램을 개발하였다 슈퍼임포즈의 영상처리 기법으로는 두개골 및 생전 사진의 윤곽선 추출, 중첩점 조정, 상,하,좌,우 각도조정, 윤곽선보정, Hue 조정, 히스토그램 조정 등 다양한 영상처리 기법을 응용하였다. 또한, 이들 영상처리기법은 법의학 체제에 입각한 슈퍼임포즈 영상합성이 개인식별 감정시 필요한 최적의 영상 비교가 가능하도록 DB 시스템 구축과 분석시스템을 개발하였다. 그리고, 실제 감정시 본 영상시스템으로 감정해 본 결과로 보다 정확하고 실시간으로 감정이 가능하다. 본 슈퍼 임포즈 영상시스템은 슈퍼 임포즈 영상자료의 처리와 축적 기술의 발전으로, 두개골 영상과 생전 사진을 이용한 생전의 3차원 실 영상의 복원연구가 가능하리라 사료된다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.3
• /
• pp.186-191
• /
• 2016

This paper addresses the development of 3D data acquisition system (3D scanner) based laser structured-light image. The 3D scanner consists of a stripe laser generator, a conventional camera, and a rotation table. The stripe laser onto an object has distortion according to 3D shape of an object. By analyzing the distortion of the laser stripe in a camera image, the scanner obtains a group of 3D point data of the object. A simple semiconductor stripe laser diode is adopted instead of an expensive LCD projector for complex structured-light pattern. The camera has an optical filter to remove illumination noise and improve the performance of the distance measurement. Experimental results show the 3D data acquisition performance of the scanner with less than 0.2mm measurement error in 2 minutes. It is possible to reconstruct a 3D shape of an object and to reproduce the object by a commercially available 3D printer.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.10
• /
• pp.811-816
• /
• 2016

In light of recently developed 3D printers for rapid prototyping, there is increasing attention on the 3D scanner as a 3D data acquisition system for an existing object. This paper presents a prototypical 3D scanner based on a striped laser light image. In order to solve the problem of shadowy areas, the proposed 3D scanner has two cameras with one laser light source. By using a horizontal rotation table and a rotational arm rotating about the latitudinal axis, the scanner is able to scan in all directions. To remove an additional optical filter for laser light pixel extraction of an image, we have adopted a differential image method with laser light modulation. Experimental results show that the scanner's 3D data acquisition performance exhibited less than 0.2 mm of measurement error. Therefore, this scanner has proven that it is possible to reconstruct an object's 3D surface from point cloud data using a 3D scanner, enabling reproduction of the object using a commercially available 3D printer.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.24 no.6
• /
• pp.895-906
• /
• 2000

The study planned to testify the accuracy of the 3D scanner through analyzing the human body measurement method and the evaluation of flare skirt with 3D scanner. The results obtained from this study were as follows; First, the results of measurement for the dress form and human body by 3D scanner were more accurate than one or two dimensional measurement method. Second, from the results of the scan for the flare skirts as worn the human body, we could obtain very accurate horizontal section map. Third, in the clothing ergonomics viewpoint, the accuracy of the 3D scanner was very excellent and its utility was higher than that of the moir photography method. Therefore, the 3D scanner is very useful for the human body measurement and the wearing evaluation. In a nutshell, this study illustrates that we have to develop a program of automatic human body measurement system which will enhance the application of the 3D scanner.

• Journal of dental hygiene science
• /
• v.15 no.5
• /
• pp.673-678
• /
• 2015

The purpose of this study was to evaluate the reliability and accuracy of linear measurements in digital models compared to master model. A master model (ANKA-4; Frasaco GmbH, Tettnang, Germany) with the prepared upper full arch tooth was used. Four linear measurements were recorded between landmarks, directly on the master model and the digital models by a single examiner. Measurements were made with a digital caliper from manual model and with the software from the virtual models. The t-test for paired samples and intraclass correlation coefficient (ICC) were used for statistical analysis. The measurement of two methods showed good reliability. The mean differences between master and digital model were 0.06~0.12 mm. These in vitro studies show that accuracy and reliability of the digital impression is similar to that of the gold standard. Therefore digital impression was also considered to be a acceptable for placement clinically.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.38 no.4
• /
• pp.233-241
• /
• 2022

Purpose: The purpose of this study was to assess the dimensional change of 3D-printed dentures after post-curing. Materials and Methods: The upper and lower dentures were designed in Exocad DentalCAD software and exported as STL files. The upper and lower dentures were printed from 10 STL files using a DLP-type dental 3D printer. The printed upper and lower dentures were cleaned, and a scan file was created using a model scanner before and after post-curing. The dimensional change was evaluated by superimposing the scanned denture files before and after post-curing and measuring the distance between measurement points on the denture. SPSS was used for statistics, and the level of significance was 5%. Results: The maxillary denture reduced in size during post-curing, with the most notable color change occurring in the posterior palatal region. The reduction in anteroposterior maxillary denture length (A-D, A-E, A-F), as well as the distance between the first molars on both sides (B-C), was statistically significant. After post-curing, the mandibular denture showed more noticeable color change in the posteriorly buccal and lingual region. The decrease of length on the posterior (A-M, A-D, A-E, A-L, A-H, A-I, H-I) and lingual (J-K, L-M) sides of the denture were statistically significant. Conclusion: There was significant dimensional change in both the length and width of the 3D-printed maxillary and mandibular dentures after post-curing in this experiment. Consequently, it is seemed necessary to develop post-curing techniques and materials that reduce such denture deformation.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.14 no.1
• /
• pp.81-96
• /
• 2012

The purpose of this study is to provide fundamental information for standardization of 3D body measurement. This research analyzes errors occurring in the process of extracting body size from 3D body scan data. First, as a result of analyzing basic state of the 3D body scanner's calibration, the point number of each section was almost the same, while the right and left as well as the front and back coordinates of the center of gravity are not, showing unstable data. Nevertheless, the latter does not influence on the size of cylinder such as width and circumference. Next, we analyzed point coordinates variations of scan data on a mannequin nude by life casting. The result was great deflection in case of complicated or horizontal sections including the reference point beyond proper distance from centers of four cameras. In case of the mannequin's size, accuracy proves comparatively high in that measurement errors in height, width, depth, and length dimension occurred all within allowable errors, only except chest depth, while there were a lot of measurement errors in a circumference dimension. Secondly, analysis of accuracy of automatic extraction identification program algorithm presented that a semi-automatic measurement program is better than an automatic measurement program. While both of them ate very acute in parts related to crotch, they are not in armpit related parts. Therefore, in extracting of human body size from 3D scan data, what really matters seems to parts related to armpits.

• Explosives and Blasting
• /
• v.37 no.4
• /
• pp.26-35
• /
• 2019

In designing a gravity-type anchorage of earth-anchored suspension bridge, the contact friction between a blasted rock mass and the concrete anchorage plays a key role in the stability of the entire anchorage. Therefore, it is vital to understand the shear behavior of the interface between the blasted rock mass and concrete. In this study, a portable 3D LiDAR scanner was utilized to scan the blasted bottom surfaces, and rock surface roughness was quantitatively analyzed from the scanned profiles to apply to 3D FEM modelling. In addition, based on the 3D FEM model, a three-dimensional dynamic fracture process analysis (DFPA-3D) technique was applied to study on the shear behavior of the interface between blasted rock and concrete through direct shear tests, which was analyzed under constant normal load (CNL). The effects of normal stress and the joint roughness on shear failure behavior are also analyzed.