• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3B
• /
• pp.277-284
• /
• 2011

The limitations of existing Markov chain model for reproducing extreme rainfalls are a known problem, and the problems have increased the uncertainties in establishing water resources plans. Especially, it is very difficult to secure reliability of water resources structures because the design rainfall through the existing Markov chain model are significantly underestimated. In this regard, aims of this study were to develop a new daily rainfall simulation model which is able to reproduce both mean and high order moments such as variance and skewness using a piecewise Kernel-Pareto distribution. The proposed methods were applied to summer and fall season rainfall at three stations in Han river watershed in Korea. The proposed Kernel-Pareto distribution based Markov chain model has been shown to perform well at reproducing most of statistics such as mean, standard deviation and skewness while the existing Gamma distribution based Markov chain model generally fails to reproduce high order moments. It was also confirmed that the proposed model can more effectively reproduce low order moments such as mean and median as well as underlying distribution of daily rainfall series by modeling extreme rainfall separately.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.3
• /
• pp.59-72
• /
• 2014

For circular rigid footings with a rough base on sand, combined vertical - moment loading capacity was studied by three-dimensional numerical modelling. Mohr-Coulomb plasticity model with the associated flow-rule was used for the soil. After comparing the results of the swipe loading method, which can construct the interaction diagram with smaller number of analyses, and those of the probe loading method, which can simulate the load-paths in the conventional load tests, it was found that both loading methods give similar results. Conventional methods based on the effective width or area concept and the results by eccentricity factor ($e_{\gamma}$) were reviewed. The results by numerical modelling of this study were compared with those of previous studies. The combined loading capacity for vertical (V) - moment (M) loading was barely affected by the internal friction angle. It was found that the effective width concept expressed in the form of eccentricity factor can be applied to circular footings. The numerical results of this study were smaller than the previous experimental results and the differences between them increased with the eccentricity and moment load. Discussions are made on the reason of the disparities between the numerical and experimental results, and the areas for further researches are mentioned.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.10 no.4
• /
• pp.204-210
• /
• 1998

This paper presents the development of the probability density function applicable for wave heights (peak-to-trough excursions) in finite water depth including shallow water depth. The probability distribution applicable to wave heights of a non-Gaussian random process is derived based on the concept of the maximum entropy method. When wave heights are limited by breaking wave heights (or water depth) and only first and second moments of wave heights are given, the probability density function developed is closed form and expressed in terms of wave parameters such as $H_m$(mean wave height), $H_{rms}$(root-mean-square wave height), $H_b$(breaking wave height). When higher than third moment of wave heights are given, it is necessary to solve the system of nonlinear integral equations numerically using Newton-Raphson method to obtain the parameters of probability density function which is maximizing the entropy function. The probability density function thusly derived agrees very well with the histogram of wave heights in finite water depth obtained during storm. The probability density function of wave heights developed using maximum entropy method appears to be useful in estimating extreme values and statistical properties of wave heights for the design of coastal structures.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2062-2072
• /
• 1991

The effect of free stream turbulence on the flow characteristics behind a circular cylinder is investigated in the present experimental study. The various free stream turbulent intensities are generated by different combinations of cylinder locations and grid shapes. Split film sensor with constant temperature anemometer is used to measure the local instantaneous velocity components. Experimental results demonstrate the large scale coherent structures are rapidly distorted and the Strouhal number is decreased with increasing free stream turbulent intensity.

• The KIPS Transactions:PartB
• /
• v.12B no.6 s.102
• /
• pp.715-720
• /
• 2005

This paper presents a hybrid recognition method of first moment of face image and principal component analysis(PCA). First moment is applied to reduce the dimension by shifting to the centroid of image, which is to exclude the needless backgrounds in the face recognitions. PCA is implemented by single layer neural network which has a teaming rule of Foldiak algorithm. It has been used as an alternative method for numerical PCA. PCA is to derive an orthonormal basis which directly leads to dimensionality reduction and possibly to feature extraction of face image. The proposed method has been applied to the problems for recognizing the 48 face images(12 Persons $\ast$ 4 scenes) of 64$\ast$64 pixels. The 3 distances such as city-block, Euclidean, negative angle are used as measures when match the probe images to the nearest gallery images. The experimental results show that the proposed method has a superior recognition performances(speed, rate). The negative angle has been relatively achieved more an accurate similarity than city-block or Euclidean.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.2
• /
• pp.251-259
• /
• 2002

A new splicing technique by the secondary moment which is intentionally induced by the tensioning effect of continuous tendons and the releasing effect of temporary beam tendons was developed. The tensioning and releasing works are essential and the decisions of the magnitude and order about them may be important engineering problems in this technique. In this paper, it was studied lot the practically optimum procedure of the tensioning and releasing works. As the result, it is concluded that the gradual progress through the three stages is reasonable for the procedure and the tensioning work have to precede the releasing work. Additionally, the magnitude of preceding tensioning force should be obtained by the sensitivity analysis and the minimum limit is more critical than the minimum limit.

• Journal of Korea Water Resources Association
• /
• v.34 no.2
• /
• pp.119-130
• /
• 2001

At-site and regional frequency analyses of annual maximum 1-, 2-, and 3-days rainfall in Han River basin was performed and compared based on the regional L-moments algorithm. To perform regional frequency analysis, Han River basin was subdivided into 3 sub-basins such as South Han River, North Han River, and downstream regions. For each sub-basin, the discordancy and homogeneity tests were performed. As the results of goodness of fit tests, lognormal model was selected as an appropriate probability distribution for both South Han River and downstream regions and gamma-3 model for North han River region. From Monte carlo simulation, RBIAS and RRMSE of the estimated quantiles from regional frequency analysis and at-site frequency analysis were calculated and compared each other. Regional frequency analysis shows less RRMSE of the estimated quantiles than at-sites frequency analysis in overall return periods. The differences of BRMSE between two approaches increase as the return period increases. As a result, it is shown that regional frequency analysis performs better than at-site analysis for annual maximum rainfall data in Han River basin.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.3
• /
• pp.273-288
• /
• 1997

In this work, the electromagnetic waves scattered from 2-dimensional random rough surfaces are characterized by the $4\times4$ Mueller matrix elements. The full wave solutions are used to compute these elements. The results of the full wave solutions for 1-dimensional random rough surfaces were shown to agree well with those of the experiment and the method of moments. The Mueller matrix elements are related to the like and cross polarized radar cross sections as well as to the relative phase of the vertically and horizontally polarized waves. The $4\times4$ Mueller matrix elements completely characterize electromagnetic scattering from target. The computed results of this paper can be useful to the field of active remote sensing or RCS.

• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.173-177
• /
• 2021

In this study, the torsional rigidity and durability of the stabilizer models with the hollow axis of light and large sized cars were compared and investigated each other. Model 1 was applied with the moment more than three times as much as model 2, but the maximum deformation of model 1 was seen to be about 2.6 times larger than that of model 2. Commonly, models 1 and 2 are seen to get the most stress at the neck of stabilizer bar link. Also, the maximum stress of model 1 was about 2.9 times larger than that of model 2. Model 1 at large car showed more than 20 times more deformed energy than model 2 at small car. Overall, it could be examined that the deformation energy of the bracket part on the side where the moment fixing the stabilizer bar was applied was greater than that of the stabilizer. It is thought that the analysis results in this study can be helped at the design of its convergent research as a durable component of the stabilizer at a light or large sized car.

• Journal of the Korea Concrete Institute
• /
• v.15 no.1
• /
• pp.11-16
• /
• 2003

The objective of this study is to clarify the seismic capacity and the characteristics in the hysteretic behavior of RC structures with non-seismic detailing. To do this, an exterior beam-column subassemblage was selected from a ten story RC building and six 1/3-scale specimens were manufactured with three variables; (1) with and without slab, (2) upward and downward direction of anchorage for the bottom bar in beams, and (3) with and without hoop bars in the joint region. The test results have shown that (1) the existence of slab increased the strength in positive and negative moment, 25% and 52%, respectively; (2) the Korean practice of anchorage (downward and 25 $d_{b}$ anchorage length) caused the 8% reduction of strength and the early strength degradation in comparison with the case of seismic details; and (3) the existence of hoop bars in the joint region shows significant role in preventing the pull-out.t.