• Journal of computational fluids engineering
• /
• v.2 no.1
• /
• pp.46-53
• /
• 1997

The flow field around a three dimensional minivan-like body has been simulated. This study solves 3-D unsteady incompressible Navier-Stokes equations on a non-orthogonal curvilinear coordinate system using second-order accurate schemes for the time derivatives, and third/second-order scheme for the spatial derivatives. The Marker-and-Cell concept is applied to efficiently solve continuity equation. A H-H type of multi-block grid system is generated around a three dimensional minivan-like body. Turbulent flows have been modeled by the Baldwin-Lomax turbulent model. To validate present procedure, the flows around the Ahmed body with 12.5° of slant angle are simulated. A good agreement with other numerical results is achived. After code validation, the flows around a mimivan-like body are simulated. The simulation shows three dimensional vortex-pair just behind body. The flow separation is also observed on the rear of the body. It has concluded that the results of present study properly agreed with physical flow phenomena.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.34-39
• /
• 2014

A study is analyzed on the design factor of center-body diffuser and performed on conceptual design of center-body diffuser with computational fluid dynamic. The flow field of center-body diffuser is calculated using axisymmetric two-dimensional Navier-Stokes equation with $k-{\epsilon}$ turbulencemodel. The center-body diffuser is compared with second throat exhaust diffuser in terms of starting pressure, the degree of vacuum pressure and the design factors. The counter flow jet on cone-tip of the center-body is applied for thermal protection system in the center-body diffuser.

• Korean Journal of Materials Research
• /
• v.16 no.11
• /
• pp.668-675
• /
• 2006

In the partial squeeze casting process, the filling behavior of liquid metal and solidification pattern in thick area have significant influence on the quality of casting products and die life. For the optimal casting design of automobile transmission gear housing, various analyses were performed in this study by using computer simulation code, MAGMAsoft and the simulation results were compared and analyzed with experimental results. By air pressure criteria, internal porosities caused by air entrap during the mold filling were predicted and reduced remarkably by modification of gating system. Also, optimal squeeze-time lag to apply partial squeeze pin in thick area was calculated and the castings was free from shrinkage defects with the result of solidification analysis. Consequently, casting design for automobile transmission gear housing was optimized and approved by Computer Tomography.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.126-132
• /
• 2016

This study numerically investigates the characteristics of chemical reactions and thermal deformation in a steam reformer. These phenomena are significantly affected by the high-temperature burner gas and the process gas conditions. Because the high temperature of the burner gas ranges from 800 to 1000 K, the reformer tubes undergo substantial thermal deformation, eventually resulting in structural failure. Thus, it is necessary to understand the characteristics of the reaction and thermal deformation under the operating conditions to evaluate the reformer tubes for sustainable, stable operation. Extensive numerical simulations were carried out using commercial CFD code (ANSYS FLUENT/MECHANICA Ver. 13.0) while considering three-dimensional turbulent flows and combined heat transfer including conduction, convection, and radiation. Structural analysis considering conjugated heat transfer between solid tubes and fluid flows was conducted using the Fluid-Solid Interaction (FSI) method. The results show that when the injection temperature of the process gas and burner gas decreased, the hydrogen production rate decreased significantly, and thermal deformation decreased by at least 15 to 20%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.113-116
• /
• 1992

소음의 발생 원인은 공기역학적 측면과 구조적 측면으로 나누어지는데, 실제 로는 유동장에서 발생되는 음원과 구조물에서 발생되는 진동과의 상호 간섭 에 의해 보다 복잡한 형태로 발생된다. 음장 문제를 두가지 범주로 구분하면 첫째는 음원과 구조물과의 상호교란에 의한 산란문제(Scattering)와 둘째로 구조물의 자체 진동에 의한 음의 전파현상과 구조물내부에 회전체와 같은 음원이 존재하는 경우에 음의 전파를 관측하는 방사문제(Radiation)가 있다. 실제로 산업용 터빈이나 비행기 엔진 흡입구에서 발생되는 소음, 또는 자동 차의 배기구를 통해 발생되는 소음 그리고 엔진의 진동에 의한 구조적 소음, 기타 가전제품의 회전체(Fan & Motor)에 의한 소음은 방사(Radiation)의 문 제로서 중요 관심 과제이다 수치적 기법으로 근래에 많이 사용하는 방법으 로 BEM(경계요소법), FEM(유한요소법), FDM(유한차분법)이 있는데 본 연 구에서는 유한요소법을 이용하기로 한다. 지금까지는 주로 BEM을 통해서 Far-Field의 음향장을 해석하였지만 복잡한 형상을 갖는 구조물내부에서의 음향장 변화나 구조물 내부에 음원이 존재하는 경우 또는 구조물 자체가 갖 는 물리적 특성치 변화 즉 물체표면에서의 부분 진동문제의 음향장 해석에 있어서 가장 잘 대체해 나갈 수 있는 방법이 유한 요소법이라고 여겨진다. 본 연구에서는 2차원 또는 기하학적으로 축대칭인 3차원 Duct내부에 음원이 존재하는 경우 음원전파에 따른 Near-field와 far-field에서 음의 방향성을 예측하기 위해 먼저 기본적인 유한요소법에 의한 Robin 경계조건을 사용하 여 계산된 결과와 Infinite Element를 도입하여 계산할 결과를 비교하여, Infinite Element가 보다 효율적이며 타당한 결과를 얻음을 확인해 보기로 한다.다 복합적인 측면에서 치료에 임하여야 할 것으로 사료된다. with such configuration.trap with 2.88[eV] deep of injected space charge from the chathode in the crystaline regions. The origin of ${\alpha}$$_2$ peak was regarded as the detrapping process of ions trapped with 0.9[eV] deep originated from impurity-ion remained in the specimen during production process of the material, in the crystalline regions. The origin of ${\beta}$ peak was concluded to be due to the depolarization process of "C=0"dipole with the activation energy of 0.75[eV] in the amorphous regions. The origin of ${\gamma}$ peak was responsible to the process combined with the depolarization of "CH$_3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과 0.05 - 0.10 mm/hr 의 범위로서 이로 인한 강우손실량은 큰 의미가 없음을 알았다.재발이 나타난 3례의 환자

• Smart Media Journal
• /
• v.9 no.4
• /
• pp.176-186
• /
• 2020

The size and shape of crops are diverse, and the growing environment is also different. Therefore, when one uses a drone to spray pesticides, the characteristics of each crop must be considered, and flight conditions such as the flight height and forwarding velocity of the drone should be changed. The droplet flow of pesticides is affected by various flight conditions, and a large change occurs in the sprayed area. As a result, an uneven distribution of liquid may be formed at the wake, and the transport efficiency will be decreased as well as there would be a risk of toxic scatter. Therefore, this paper analyzes the degree of distribution of pesticides to the crops through numerical analysis when pesticide is sprayed onto the selected three crops with different characteristics by using agricultural drones with different flight conditions. On the purpose of establishing a guideline for spraying pesticides using a drone in accordance with the characteristics of crops, this paper compares the amount of pesticides distributed in the crops at the wake of nozzle flow using the figure of merit, and the sum of transported liquid rate divided by the root mean square of the probability density function.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.69-74
• /
• 2015

The study investigated numerically the heat transfer and chemical reaction characteristics of a methane-steam reforming by using a 3-dimensional computational fluid dynamics (CFD) code (Fluent ver. 16.1). The fuel temperature and its species mole fractions were estimated for various Reynolds number in the reformer tube at different burner temperatures. The catalysts were modeled as the porous medium of nicrome in the reformer tube. We considered radiation effect as well as conduction and convective heat transfer because the methane-steam was reformed at very high temperature condition above 1000 K. For two different Reynolds numbers of 49,000 and 88,000 and the burner temperatures were in the range from 1,100 K to 1,300 K. At a low Reynolds number, the fuel temperature increased, leading to increase in hydrogen reforming. However, fuel temperature and hydrogen reforming decreased because of higher convective heat transfer from relatively low fuel temperature. Moreover, the hydrogen reforming also increased with burner temperature.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.4
• /
• pp.319-345
• /
• 2011

In case of tunnels in cold regions, a freeze of groundwater around tunnel may act as a barrier of tunnel drainage in winter, or may cause the inner extrusion of lining. In spite of that, a design of insulation for preventing the frost damage of tunnel lining has not been introduced in Korea, while foreign countries such as Norway and so on have a standard on insulation. In this study, a few freezing cases of road tunnels have been reviewed, and the results show that the freezing protection is necessary. In order to characterize the thermal distribution in the tunnel, following measurements have been performed at Hwa-ak tunnel; the temperature distribution by longitudinal lengths, the internal temperature of lining and the temperature distribution of the ground under pavement. From these measurements, the characteristics of the tunnel's internal temperature distribution due to temperature change in the air has been analyzed. Based on the measurement results on the temperature distribution at Hwa-ak tunnel, thermal flow tests on the rock specimen with and without insulation have been performed in the artificial climate chamber to investigate the performance of the insulation. Also, a number of 3D numerical analyses have been performed to propose appropriate insulation and insulation thicknesses for different conditions, which could prevent the frost damage of tunnel lining. As a result of the numerical analysis, air freezing index of 291$^{\circ}C{\cdot}$ Hr has been suggested as the threshold value for freezing criteria of groundwater behind the tunnel lining.

• 한국해양학회지
• /
• v.29 no.2
• /
• pp.95-106
• /
• 1994

Tidal and wind-driven currents in Chinhae Bay are investigated using a three-dimensional numerical model developed by Kim et al. (1993). The simulations indicate that the flow patterns in the bay are predominated by the bathymetry, wind and river inflow, and the effects of wind on the flow pattern in the inner bay are much stronger than those in the entrance channel. Computed tidal currents coincide with the field measurements. The horizontal and vertical velocities of tidal and residual currents are strong in the entrance channel of the bay, whereas the velocities are relatively weak in the western and northern parts of the bay. Computed velocity fields show the expected phase difference between the velocities in the surface and those in the bottom layer, and these characteristics are more remarkable during the spring tide than the neap tide. The surface currents in the bay depend strongly on the wind and river inflow, and such phenomena are more remarkable during the neap tide than the spring tide.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.88-96
• /
• 2017

The subway can transport a lot of people at a certain route at once, and the railway and the platform are underground, so it is advantageous to use the ground space efficiently. But If a fire occurs in a subway that is used by an unspecified number of people, such as the Daegu Subway Fire Disaster, many casualties can occur. As a result of the previous research, it was confirmed that the performance of the ventilation system of the old subway platform was remarkably degraded. Therefore, in this study, based on the experimental results of the previous research, we confirmed the flow of the hot and CO flows according to the ventilation mode in the case of fire by three - dimensional numerical analysis. As a result, it was found that the old ventilation system could not maintain the hot air temperature below the reference value for 4 minutes based on the evacuation time of the platform, and when the ventilation performance was enhanced by adding Oversized Exhaust Ports at the upper part of the platform, And the temperature of the heat flow can be maintained.