• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.146-150
• /
• 2005

A nano-stereolithouaphy (NSL) apparatus has been developed for fabrication of microstructures with the resolution of 150 nanometers. In the NSL process, a complicated 3D structure can be fabricated by building layer by layer, so it does not require any sacrificial layer or any supporting structure. A laminated layer was fabricated by means of solidifying liquid-state monomers using two-photon absorption (TPA) which was induced by a femtosecond laser. When the fabrication of a 3D laminated structure was finished, unsolidified liquid-stage resins were removed to develop the fabricated structure by dropping several droplets of solvent, then the polymerized structure was only left on the glass substrate. A microstructure is fabricated by vector scanning method to save the fabrication time. The shell thickness of a structure is very thin within 200 nm, when it is fabricated by a single contour scanning (SCS) path. So, a fabricated structure can be deformed easily in the developing process. In this work, a double contour scanning (DCS) method was proposed to reinforce the strength of a shell typed structure, and a microcup was fabricated to show the usefulness of the developed NSL system and the DCS method.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.2
• /
• pp.41-47
• /
• 1990

최근 열에너지를 기계에너지로 변환이 가능한 신소재인 형상기억합금으로 제작된 새로운 형태의 actuator를 이용한 해저로봇의 개발에 관하여 많은 연구들이 행하고 있다. 저자들은 로봇의 모양을 실제 동물의 형태인 "게" 모양으로 하고, 로봇을 구동시키는 게의 다리의 모든 연결부분의 인공근육을 Ni-Ti계 형상기억합금 스프링 또는 와이어로 구성되어져 있으며, 마이크로 컴퓨터에 의하여 구동이 자유로이 조절이 가능한 게 형태의 모양 로봇을 실제의 1/20크기로 제작하였다. 이 로봇의 특징은 구조가 간단하고, 고강도, 고내식성 그리고 부드럽고 자유롭게 3차원적 동작이 가능하다는 것을 들 수 있다. 해저 로봇의 최종목표는 심해자원의 탐사 및 채굴이 이용하는 것이다. 따라서 본 연구에서는 그 가능성 및 기술적 문제 그리고 미래의 이러한 형상기억합금 로봇에 의한 심해자원 탐사를 위한 국제적인 협력의 필요성에 대하여 연구 검토하고자 한다. 검토하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.9
• /
• pp.623-629
• /
• 2017

Flow structure and mixing characteristics in a micro combustor with a multi-hole baffle were numerically studied using the Reynolds stress model. The multi-hole baffle has geometrical features to produce multiple three-dimensional vortices inside combustion chamber. When the thickness of the baffle's geometrical factors changes, variations of vortical structures occur variously. Among these vortices, the vortex generated from the fuel stream exerts a critical influence on the mixing enhancement. The three-dimensional vortical structure, in its development state, was strongly dependent on the baffle thickness. In particular, as the baffle thickness decreases to values less than the diameter of the fuel hole, the jet stream in baffle holes changes from the parabolic to saddleback profile type. The sizes of recirculation zones inside combustion chamber and the mixing state were closely affected by the structure of the jet streams.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.5
• /
• pp.405-414
• /
• 2015

Fluid transport is a key issue in the development of microfluidic systems. Recently, Myong (2014) has proposed a new concept for droplet transport without external power sources and numerically validated the results for a hypothetical 2D, initially having a hemicylindrical droplet. In this paper, the movement of an actual water droplet, initially having a 3D hemispherical shape, on horizontal hydrophilic/hydrophobic surfaces is simulated using a commercial computational fluid dynamics (CFD) package, Fluent, with VOF (volume of fluid) method. The results are compared with the 2D analysis of Myong (2014), and the transport mechanism for the actual water droplet is examined based on the numerical results of the time evolution of the droplet shape, as well as the total kinetic, gravitational, surface free and pressure energies inside the droplet.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.65-67
• /
• 2006

압전현상을 응용하여 설계, 제작되는 기존의 초음파 모터는 기계적인 구조가 단순하여 설계가 비교적 용이한 장점을 갖추고 있는 반면, 그 해석에 있어서는 전통적일 수치해석적인 방법을 사용하고 trial-and-error에만 의존하는 설계 방식으로 인하여 과학적으로 최적화된 설계가 이루어지지 않음으로써 초음파 모터의 효과적인 설계가 이루어지지 않는 문제점이 존재 하였다. 따라서 본 연구에서는 3차원 유한요소법과 확률론적 최적화 기법인 진화전략 알고리즘을 이용하여 초음파 모터의 설계에 대한 최적화 기법을 제시하고 제시된 최적화 기법을 이용하여 소형 초음파 모터 중 Micro-Positioning Actuator(MPA)의 설계 및 해석을 수행하여 그 타당성을 검증하였다.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.531-534
• /
• 2006

This study is concerned with radial turbine design and performance improvement of a turbo generator system, which is used for maximizing performance of a 250kW MCFC fuel cell system. A preliminary design of a radial turbine has been performed under the thermodynamic and fluid-dynamic conditions determined by a cycle analysis of the MCFC BOP system. Basic demensions are determined by a meanline analysis and calculation of radial variation at the exit of the turbine. The turbine impeller is designed and modified by iterative processes of three dimensional flow analysis.

• The korean journal of orthodontics
• /
• v.38 no.4
• /
• pp.228-239
• /
• 2008

Objective: The aim of this study was to evaluate the strain induced in the cortical bone surrounding an orthodontic microimplant during insertion. Methods: A 3D finite element method was used to model the insertion of a microimplant (AbsoAnchor SH1312-7, Dentos Co., Daegu, Korea) Into 1 mm thick cortical bone with a pre-drilled hole of 0.9 mm in diameter. A total of 1,800 analysis steps was used to simulate the 10 turns and 5 mm advancement of the microimplant. A series of remesh in the cortical bone was allowed to accommodate the change in the geometry accompanied by the implant insertion. Results: Bone strains of well higher than 4,000 microstrain, the reported upper limit for normal bone remodeling, was observed in the bone along the whole length of the microimplant. At the bone in the vicinity of the screw tip, strains of higher than 100% was recorded. The insertion torque was calculated at approximately 1.2 Ncm which was slightly lower than those measured from the animal experiment using rabbit tibias. Conclusions: The insertion process of a microimplant was successfully simulated using the 3D finite element method which showed that bone strains from a microimplant insertion might have a negative impact on physiological remodeling of bone.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.5
• /
• pp.331-338
• /
• 2020

In this study, the characteristic of a 3-D micro-woven material, which is one of the newly developed periodic open-cell structure, is analyzed through various computational simulations. To increase the accuracy of the numerical simulations, the distance between each directional wire is parameterized using six design variables, and its model geometry is precisely discretized using tetrahedron elements. Using the improved computational model, the material properties of the mechanical, thermal, and fluidic behavior are investigated using commercial software and compared with the previous experimental results. By changing the space between the x- and y-directional wires, a parametric test is performed to determine the tendency of the change in the material properties. In addition, the correlation between two different material properties is investigated using the Ashby chart. The result can further be used in determining the optimal pattern and wire spacing in 3-D micro-woven materials.

• Transactions of Materials Processing
• /
• v.15 no.9 s.90
• /
• pp.673-678
• /
• 2006

Demands for micro parts have increased with recent advances in IT and machinery industries. However, the present technology loaves much to be desired to effectively produce parts with the volume of $1mm^{3}$ and less by mechanical method in large quantities. This paper provides a method for efficient quantity production of complete micro 3D structure using micro end-milling cutting process. The possibility has proven via manufacturing experiment of a multistage micro complex gear structure of $500{\mu}m$ in length, $500{\mu}m$ in maximum external diameter and a volume of $1mm^{3}$ and less.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.943-951
• /
• 2014

The tip geometries of the pyramidal and conical indenters used for micro/nano-indentation tests are not sharp. They are inevitably rounded because of their manufacturability and wear. In many indentation studies, the tip geometries of the pyramidal indenters are simply assumed to be spherical, and the theoretical solution for spherical indentation is simply applied to the geometry at a shallow indentation depth. This assumption, however, has two problems. First, the accuracy of the theoretical solution depends on the material properties and indenter shape. Second, the actual shapes of pyramidal indenter tips are not perfectly spherical. Hence, we consider the effects of these two problems on indentation tests via finite element analysis. We first show the relationship between the Poisson's ratio and load-displacement curve for spherical indentation, and suggest improved solutions. Then, using a possible geometry for a Berkovich indenter tip, we analyze the characteristics of the load-displacement curve with respect to the indentation depth.