• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.527-539
• /
• 2018

The subway used by many passengers is required to maintain a safe and comfortable environment and PSD (Platform Screen Door) must be installed in the platform after reinforcing the standard in 2003. In the previous research, in case of subway fire to control it, it is necessary to design the optimal ventilation and smoke exhaust system according to equipment capacity of the smoke exhaust system. Therefore, in this study, based on the results of previous research, three-dimensional numerical analysis was performed for the CO gas and smoke flow by the subway ventilation system in case of platform fire. As a result of this study, it was found that in case of emergency, if only the upper-level smoke exhaust system is activated, the risk of evacuation is high due to CO gas (653.8 ppm) and smoke concentration ($768.4mg/m^3$). And when all the smoke exhaust systems are activated and only the fire side PSD is opened, CO gas (36.0 ppm) and smoke concentration ($26.2mg/m^3$) are detected and the propagation range of smoke flow was reduced. When all the smoke exhaust systems are activated and only the fire side PSD is closed, it was analyzed as the most effective ventilation mode in the evacuation environment due to the absence of smoke-recirculation.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.51-59
• /
• 2002

This paper deals with development of a damage risk assessment system for adjacent buildings to under-passing tunnel face considering 3D-ground movement. The system consists of building and ground information module, monitoring data module, settlement evaluation module, and building damage risk assessment module. The major modules, settlement evaluation module and building damage assessment module, are based on settlement estimation model suggested by Attewell et al (1982) and the building damage assessment method by Mair et al. (1996). After estimating 3D-ground movements due to tunneling with settlement evaluation module, damage assessment far buildings is performed using building damage risk assessment module. The developed system has two major functions; 1) calculation of 3D-settlement with ground loss ($V_{s}$)or maximum settlement ($w_{max}$) and inflection point (i) using various empirical formulae, monitoring data, numerical results, and so on; 2) assessment of damage risk for adjacent buildings of arbitrary section with position change of tunnel face. The field data given by Boscadin and Cording (1989) leer the case of two-storied masonry building near the Metro tunnel in Washington D.C. was simulated to verify the applicability of the developed system.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.41-53
• /
• 2016

Stability of the braced earth wall in the composite ground, which is composed of the jointed base rocks and the soil strata depends on the earth pressure acting on it. In most cases, the earth pressure is calculated by the empirical method, in which base rocks are considered as a soil strata with the shear strength parameters of base rocks. In this case the effect of the joint dips of the jointed base rocks is ignored. Therefore, the calculated earth pressure is smaller than the actual earth pressure. In this study, the magnitude and the distribution of the earth pressure acting on the braced wall in the composite ground depending on the joint dips of the base rocks and the ratio of soil strata and base rocks were experimentally studied. Two dimensional large-scale model tests were conducted in a large scale test facility (height 3.0 m, length 3.0 m and width 0.5 m) by installing 10 supports in a scale of 1/14.5. The test ground was presumed with the base rock ratio of the composite ground of 65%:35% and 50%:50% and with the joint dips for each base rock layer, $0^{\circ}$, $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$, respectively. And then finite element analyses were performed in the same condition. As results, the earth pressure on the braced wall increased as the base rock layer's joint dips became larger. And earth pressure at the rock layer increased as the rock rate became larger. The largest earth pressure was measured when the base rock rate was 50% (R50) and the rock layer's joint dips was $60^{\circ}$. Based on these results, a formular for the calculation of the earth pressure in the composite ground could be suggested. Distribution of earth pressure was idealized in a quadrangular form, in which the magnitude and the position of peak earth pressure depended on the rock ratio and the joint dips.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.4
• /
• pp.355-364
• /
• 2016

Recently, a 3,250 meter-long tunnel was constructed beneath the sea bed formed of composite sedimentary soils to transport reusable waste heat gas of industrial complex in the west coast of Korea. Some risks such as machine settlement always exist due to the uncertainties of geological and construction factors during the subsea shield TBM tunnelling. In this construction site, the deviation of tunnel alignment caused by shield TBM settlement was occurred during excavation. It was examined that the lack of bearing capacity of soft clay was a main cause. This paper evaluates the risk of shield TBM tunnelling considering the ground conditions. Correlation between machine settlement and its advance rate was evaluated through the analytical equation in which bearing capacity is considered and a 3-D numerical analysis which can simulate the TBM advance condition (in other words, the dynamic condition). It was found out that a shield TBM could settle due to the insufficient bearing capacity of soft clay layers. In order to prevent such the problem, the best advance rate proper to the ground characteristics is needed to be applied. In the ground conditions of the section of interest, it was turned out that if the shield TBM advance rate was maintained between 35 mm/min and 40 mm/min, the machine settlement could be avoided.

• Tunnel and Underground Space
• /
• v.26 no.5
• /
• pp.396-408
• /
• 2016

Rock fracture mechanics has been widely applied to various fields of rock and civil engineering. But most researches covered mode I behavior, though mode II behavior is dominant in rock engineering. Until now, there is only one ISRM suggested method for mode II toughness of rock. A new SCC (Short Core in Compression) mode II toughness test method was developed considering 1) application of confining pressure, 2) easiness of notch creation, 3) utilization of existing equipment, 4) simple test procedure. The stress intensity factors were determined by 3D finite element method considering line and distributed loading conditions. The tests with granite specimens were carried out using MTS 815 rock test system with a loading rate of 0.002 mm/s. The mean value of mode II fracture toughness of granite showed $2.33MPa{\sqrt{m}}$. Mode I toughness of the same granite was $1.12MPa{\sqrt{m}}$, determined by Brazilian disk test and $K_{IIC}/K_{IC}=2.08$. The smooth fracture surface with rock powder formation also supported mode II behavior of SCC method. The SCC method can be used for the determination of mode II fracture toughness of rocks based on the current results.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.403-411
• /
• 2016

A three-dimensional finite element analysis was conducted to analyze the predictable distances of a fault zone by using longitudinal displacement on tunnel face, trend line, L/C ratio, and C/C₀ ratio at tunnel crown. The analysis used 28 numerical models with various fault attitudes. As a result, those faults that have drives with dip could be predicted earliest in L/C and C/C₀ ratio analysis. And those faults that have drives against dip could be predicted earliest in L/C ratio and longitudinal displacement analysis. In addition, the fault zone ahead of tunnel was predicted in most models by using longitudinal displacement, trend line, L/C ratio, and C/C₀ ratio. However, the longitudinal displacement among these methods may be most usefully predict a fault zone since it is displacements can be measured immediately after tunnel excavation.

• Proceedings of the KOR-KST Conference
• /
• 1998.10b
• /
• pp.508-508
• /
• 1998

위험물 차량사고는 일반차량의 교통사고시 발생하는 인명피해, 재산피해, 교통지체 외에 부가적으로 환경적 영향에 의한 엄청난 인명 및 재산손실을 유발시킬 수 있다. 따라서 이러한 위험물차량사고를 예방하고 피해를 최소로 줄이기 위해서는 위험물수송경로의 신중하고 체계적인 결정이 필수적이라 할 수 있다. 외국의 경우, 위험물의 방출이 미치는 환경적 영향에 대한 인식이 확대되면서 위험물 수송시 응급처리에 관한 연구, 위험물 수송에 따른 위험도 평가에 관한 연구, 위험물 수송시 고려해야할 여러 조건에 관한 연구, 위험물 수송경로 설정에 관한 연구 등이 진행되고 있다. 반면에 우리 나라는 위험물차량관리와 사고처리에 대해 실시간적인 관리를 목표로 하는 국가차원의 계획을 수립하고는 있지만, 현재 이와 관련된 연구는 거의 없는 실정이다. 앞으로 산업발달에 따른 위험물수송량의 증가와 환경의식의 변화에 따라 위험물수송 및 사고처리 등에 관한 연구가 필요할 것이다. 따라서, 본 연구는 위험물차량의 운송경로를 결정할 때 고려해야 할 여러 가지의 기준 및 목표에 따라 위험물수송경로를 설정하는 모형을 제시함으로써 위험물수송에 수반되는 위험을 최소화하면서 위험물차량의 통행시간, 거리, 비용 등을 최적화하여 위험물수송의 안전 및 운영효율성을 향상시키고자 한다. 먼저, 위험물 수송경로의 기준지표로 사용될 위험도를 산정하기 위해 링크 주변노출인구, 밀도 등을 변수로 하는 모형식을 제안하고, 두 번째로 산정된 위험도를 기반으로 최적경로를 결정하는 알고리즘을 제안하였다. 마지막으로 가상 네트웍에 본 연구에서 제안된 모형을 적용하고 현재 일반적으로 사용되는 최단경로와 비교·분석하였다.것은 운송거리와 운송비용이 각각 주요한 변수라는 것이다. 모형의 타당성을 검증하기 위해서는 logilikelihood 값을 구하여 $\rho$^2분석을 시행하였다. 여기서는 각 품목별로 $\rho$^2값이 약 0.15~0.3의 비교적 높은 수치를 보여주고 있으므로 모형의 설명력이 어느 정도 있다는 것이 아울러 증명이 되었다. 상관관계에 대한 분석에서는 영업용 차량간의 상관관계가 높게 나타났으며, 이는 곧 영업용 화물차량을 적재중량별로 구분하는 것이 별 의미가 없음을 의미한다. 다시 말하면 자가용 차량을 보유하고 있지 않은 회사는 다른 운송전문업체에 화물운송을 의뢰하게 되므로 출하중량에 따라 화물차량을 구분하는 것에 대해서 그다지 큰 고려를 하지 않는 것으로 해석할 수가 있다.적합함을 재확인함. 6. 혼잡초기를 제외한 혼잡기간 중 대기행렬길이는 밀도데이터 없이도 혼잡 상류부의 도착교통량과 병목지점 본선통과교통량만을 이용하여 추정이 가능함. 7. 이상에 연구한 결과를 토대로, 고속도로 대기행렬길이를 산정할 수 있는 기초적인 도형을 제시함.벌레를 대상으로 처리한 Phenthoate EC가 96.38%의 방제가로 약효가 가장 우수하였고 3월중순 및 4월중순 월동후 암컷을 대상으로 처리한 Machine oil, Phenthoate EC 및 Trichlorfon WP는 비교적 약효가 낮았다.>$^{\circ}$E/$\leq$30$^{\circ}$NW 단열군이 연구지역 내에서 지하수 유동성이 가장 높은 단열군으로 추정된다. 이러한 사실은 3개 시추공을 대상으로 실시한 시추공 내 물리검층과 정압

• The Journal of the Convergence on Culture Technology
• /
• v.5 no.3
• /
• pp.345-349
• /
• 2019

In Korea, the mountainous area occupies more than 70% of the whole country, cutting of earth slope that cuts a part of the ground surface is widely used when building infrastructures such as road, railroad, and industrial complex construction. In recent years, regulations on environmental damage have become more strict, and various methods have been developed and applied. Among them, Concrete-Panel Retaining Wall technique is actively applied. Concrete-Panel Retaining Wall is a method to resist horizontal earth pressure by forming a wall by attaching a precast retaining wall to the front of the support material and increasing the shear strength of the disk through reinforcement of the support material. Soil nailing, earth bolt, and ground anchor are used as support material. Among them, ground anchor is a more aggressive reinforcement type that introduces tensile load in advance to the steel wire, and a large concentrated load acts on the front panel. This concentrated load is a factor that creates cracks in the concrete panel and reduces the durability of the retaining wall itself. In this study, steel pipe sleeves and reinforcements were purchased at the anchorage of the panel to prevent cracks, and by applying bumpy shear keys to the end of the panel, the weakness of the individual behavior of the existing grout anchors was improved. The problem of degraded landscape by exposure to front concrete of retaining wall and protrusion of anchorage was solved by the production of natural stone patterns and the construction of sections that do not protrude the anchorage. In order to verify the effectiveness of anti-crack sleeves and reinforcements used in the null, indoor testing and three-dimensional numerical analysis have been performed, and the use of steel pipe sleeves and reinforcements has demonstrated the overall strength increase and crack suppression effect of panels.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.113-132
• /
• 1999

Recently in Korea, application of the soil nailing is gradually extended to the sites of excavations and slopes having various ground conditions and field characteristics. Design of the soil nailing is generally carried out in two steps, The First step is to examine the minimum safety factor against a sliding of the reinforced nailed-soil mass based on the limit equilibrium approach, and the second step is to check the maximum displacement expected to occur at facing using the numerical analysis technique. However, design parameters related to the soil nailing system are so various that a reliable design method considering interrelationships between these design parameters is continuously necessary. Additionally, taking into account the anisotropic characteristics of in-situ grounds, disturbances in collecting the soil samples and errors in measurements, a systematic analysis of the field measurement data as well as a rational technique of the optimum design is required to improve with respect to economical efficiency. As a part of these purposes, in the present study, a procedure for the optimum design of a soil nailing excavation wall system is proposed. Focusing on a minimization of the expenses in construction, the optimum design procedure is formulated based on the genetic algorithm. Neural network theory is further adopted in predicting the maximum horizontal displacement at a shotcrete facing. Using the proposed procedure, various effects of relevant design parameters are also analyzed. Finally, an optimized design section is compared with the existing design section at the excavation site being constructed, in order to verify a validity of the proposed procedure.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.3
• /
• pp.159-168
• /
• 2005

In the previous studies, settlement behaviors of granular compaction piles have generally been analyzed with an evaluation of the settlement reduction factor based on tile load-sharing ratio and the replacement ratio. In this approach, however, since the reinforced ground with granular compaction piles is simplified as the composite ground, only the difference of a relative vertical strength between piles and soils is taken into account without reflecting lateral behaviors of granular compaction piles. In the companion research paper, the method of estimating the settlement of granular compaction piles was proposed by synthetically considering a vertical strength of the ground, lateral behaviors of granular compaction piles, the strength of pile materials, a pile diameter, and an installation distance of the pile. In the presented study, to validate a propriety of the previously proposed method, large scale field load tests and three dimensional numerical analyses are performed. The results are analyzed in detail and compared with the predicted settlements by the proposed method. Finally, a simple method to estimate the settlement of granular compaction piles is suggested for an easy application of the practical design.