• Journal of the Society of Disaster Information
• /
• v.14 no.3
• /
• pp.343-351
• /
• 2018

Purpose: Recently, As the size of the structure increased, the necessity of reducing its weight was raised. To reduce weight In concrete structures, a hollow slab is proposed as an alternative for weight reduction effect. Method: It is difficult to construct the hollow body due to buoyancy, and the shear performance is insufficient due to the decreased cross section. Slabs were fabricated using unidirectional hollow bodies such as PVC pipes, and experiments were conducted about construction performance and structural performance. Results: The buoyancy preventive device has been improved the construction performance by preventing floating hollow body, it has been confirmed that it has adequate performance to be used as a hollow slab system because it has enough expected shear performance. Coclusion: Hollow ratio has a little connection with bending performance, but after the yielding load, it is necessary to consider the secondary stiffness of structure, and is is supposed that the decrease of shear performance with the increase of hollow core ratio can be complemented with shear reinforcement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.17-24
• /
• 2024

This paper assesses the structural performance of the Daeungbojeon Hall of Magoksa in Gongju, a representative multi-tiered roof traditional timber structure from the Joseon Dynasty, under vertical loads. Employing midas Gen, a structural analysis software, we developed a three-dimensional analysis model closely resembling the actual structure. Static analysis was employed to evaluate the safety and serviceability of the main vertical and horizontal members under vertical loads. While all members met the safety and serviceability criteria, structural weaknesses were identified in the Daelyang of the lower floor, particularly as a transitional beam, necessitating improvement. For the evaluation of dynamic behavior characteristics, eigenvalue analysis was conducted, assuming a relative rotational stiffness of 5% at the main joints. The natural period was determined to be 1.105 seconds, placing it within the category of a Hanok of similar size. The first mode manifested as a translational movement in the forward and backward direction of the building.

• Ocean and Polar Research
• /
• v.25 no.3
• /
• pp.315-329
• /
• 2003

During the 1st Korea-Russia Arctic Expedition from 3 to 26 August, 2000 phytoplankton biomass and nutrient concentration were measured in the Barents and Kara Seas. Total of 57 surface samples were collected f3r the phytoplankton related measurements. Chlorophyll a (chi a) concentraitons were measured to investigate the relations between physico-chemical factors and phytoplankton biomass distribution. Chl a values ranged from 0.14 to $2.34mg\;m^{-3}$ (mean of $0.65{\pm}0.42mg\;m^{-3}$) over the surface stations. The elevated values of the chi a concentrations $(1.49{\sim}2.34mg\;m^{-3})$ were found in the southeastern Barents Sea near the Pechora River. Nanoplanktonic $(<20{\mu}m)$ phytoflagellates were the important contributors for the increase of the chi a. The nano-sized phytoflagellates accounted for more than 80% of the total chi a biomass in the study area. Mean chi a concentration in the Barents Sea $(0.72{\pm}0.57 mg\;m^{-3})$ was higher than in the Kan Sea $(0.52{\pm}0.45mg\;m^{-3})$, but there was no big difference between two areas. Surface temperatures and salinities ranged from 4.1 to $11.7^{\circ}C$ (mean of $8.8{\pm}1.9^{\circ}C$) and from 23.8 to 32.5psu (mean of $30.3{\pm}1.9^{\circ}C$ psu), respectively. The physical factors were not highly correlated with phytoplankton distribution. It is speculated that the insignificant correlation between phytoplankton biomass and physical factor was due to the same current which introduced similar water mass with higher water temperature and lower salinity into the study area. The mean values of major nutrients such as ammonia, nitrite, nitrate, phosphate, and silicate were $0.42{\pm}0.31{\mu}M,\;0.10{\pm}0.03{\mu}M,\;1.44{\pm}1.03{\mu}M,\;0.35{\pm}0.12{\mu}M,\;10.99{\pm}3.45{\pm}M$, respectively. The relations between phytoplankton biomass and nutrient concentration were not close, indicating that the surface nutrient concentrations during the study seem to be controlled by other physical factors such as input of fresh water (i.e. dilution effects).

• Clean Technology
• /
• v.18 no.2
• /
• pp.162-169
• /
• 2012

Pt-Sn/${\theta}-Al_2O_3$ catalyst for n-butane dehydrogenation reaction was prepared by incipient wetness method. To confirm the physicochemical properties of Pt-Sn/${\theta}-Al_2O_3$ catalyst, the characterization was performed using X-ray diffraction (XRD), $N_2$ sorption analysis, temperature programmed desorption of $NH_3$ ($NH_3$-TPD), temperature programmed reduction of $H_2$ ($H_2$-TPR) techniques. Also, the catalytic activities of Pt-Sn/${\theta}-Al_2O_3$ for n-butane dehydrogenation was tested as a function of pretreatment temperature, pretreatment time, reaction temperature, and the partial pressure of n-butane and hydrogen. The sum of selectivities to n-butenes consisting of 1-butene, cis-2-butene, and trans-2-butene was almost constant 95% in the range of conversion of n-butane 5-55%. The activation energy calculated from Arrhenius equation was $82.4kJ\;mol^{-1}$ and the reaction orders of n-butane and hydrogen from Power's law were 0.70 and -0.20, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.9-14
• /
• 2009

The effects of post-annealing temperature on the optical and electrical properties of P-doped ZnO thin films grown on sapphire substrate have been investigated under oxygen ambient. The XRD shows that regardless of the post-annealing temperature, all P-doped ZnO thin films indicate the c-axis orientation. The results of hall effect measurements indicate the P-doped ZnO thin film annealed at $850^{\circ}C$ exhibits p-type behavior with hole concentration of $1.18{\times}1016cm^{-3}$ and hole mobility of $0.96cm^2/Vs$. The low-temperature (10K) Photoluminescence results reveal that the peak related to the neutral-acceptor exciton (A0X), free electrons to neutral acceptor (FA) and donor acceptor pair (DAP) at 3.351ev, 3.283eV and 3.201eV are observed in the films showing p-type behavior with acceptor. The optimization of deposition and post-annealing conditions will certainly make the P-doped ZnO thin films promising materials for the application to the next generation of optical devices.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.6
• /
• pp.1095-1100
• /
• 2021

In this study, ITZO thin films were deposited on glass, sapphire, and PEN substrates by RF magnetron sputtering, and their electrical and optical properties were investigated. The resistivity of the ITZO thin film deposited on the glass and sapphire substrates was 3.08×10-4 and 3.21×10-4 Ω-cm, respectively, showing no significant difference, whereas the resistivity of the ITZO thin film deposited on the PEN substrate was 7.36×10-4 Ω-cm, which was a rather large value. Regardless of the type of substrate, there was no significant difference in the average transmittance of the ITZO thin film. Figure of Merits of the ITZO thin film deposited on the glass substrate obtained using the average transmittance in the absorption region of the amorphous silicon thin film solar cell and the absorption region of the P3HT : PCBM organic active layer were 10.52 and 9.28×10-3 Ω-1, respectively, which showed the best values. Through XRD and AFM measurements, it was confirmed that all ITZO thin films exhibited an amorphous structure and had no defects such as pinholes or cracks, regardless of the substrate type.

• Economic and Environmental Geology
• /
• v.40 no.4
• /
• pp.473-490
• /
• 2007

Strata of the Kachi-1 well, Kunsan Basin, offshore western Korea, were analyzed by using integrated stratigraphy approach. As a result, five distinct unconformity-bounded units are recognized in the well: Triassic, Late Jurassic-Early Cretaceous, Early Cretaceous, Late Cretaceous, and Middle Miocene units. Each unit represents a tectono-stratigraphic unit that provides time-sliced information on basin-forming tectonics, sedimentation, and basin-modifying tectonics of the Kunsan Basin. In the late Late Jurassic, development of second- or third-order wrench faults along the Tan-Lu fault system probably initiated a series of small-scale strike-slip extensional basins. Continued sinistral movement of these wrench faults until the Late Cretaceous caused a mega-shear in the basin, forming a large-scale pull-apart basin. However, in the Early Tertiary, the Indian Plate began to collide with the Eurasian Plate, forming a mega-suture zone. This orogenic event, namely the Himalayan Orogeny, continued by late Eocene and was probably responsible for initiation of right-lateral motion of the Tan-Lu fault system. The right-lateral strike-slip movement of the Tan-Lu fault caused the tectonic inversion of the Kunsan Basin. Thus, the late Eocene to Oligocene was the main period of severe tectonic modification of the basin. After the Oligocene, the Kunsan Basin has maintained thermal subsidence up to the present with short periods of marine transgressions extending into the land part of the present basin.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.578-584
• /
• 2017

$SiO_2$ buffer layer (100 nm) has been deposited on PET substrate by electron beam evaporation. And then, IZTO (In-Zn-Sn-O) thin film has been deposited on $SiO_2$/PET substrate with different RF power of 30 to 60 W, working pressure, 1 to 7 mTorr, by RF magnetron sputtering. Structural, electrical and optical properties of IZTO thin film have been analyzed with various RF powers and working pressures. IZTO thin film deposited on the process condition of 50 W and 3 mTorr exhibited the best characteristics, where figure of merit was $4.53{\times}10^{-3}{\Omega}^{-1}$, resistivity, $4.42{\times}10^{-4}{\Omega}-cm$, sheet resistance, $27.63{\Omega}/sq.$, average transmittance (400-800 nm), 81.24%. As a result of AFM, all the IZTO thin film has no defects such as pinhole and crack, and RMS surface roughness was 1.147 nm. Due to these characteristics, IZTO thin film deposited on $SiO_2$/PET structure was found to be a very compatible material that can be applied to the next generation flexible display device.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.17-32
• /
• 2002

The purpose of this study was to find the rational method to analyze golf swing with specific property of club shaft. Three subjects were filmed by two high speed digital cameras with 500 fps. The phase analyzed was downswing of each subject. The three-dimensional coordinates of the anatomical landmarks were obtained with motion analysis system Kwon3d 3.0 version and smoothed by lowpass digital filter with cutoff frequency 6Hz. From these data, kinematic and kinetic variables were calculated using Matlab(ver 5.0) The variables for this study were angular velocity and accelerations, which were calculated and following conclusions have been made : 1) Golf swing time of stiff club is faster than that of regular club. 2) In shoulder joint motion of swing with the stiff club, x-stiff showed mort rapid negative acceleration than that of regular club. 3) In regular club, the velocity of club head would be more effective velocity, which was increasing, than those of other clubs before impact. 4) In wrist joint motion of swing with stiff club, x-stiff club showed faster than regular club in the downswing and impact more rapid negative acceleration.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.19 no.4
• /
• pp.97-105
• /
• 2011

A wide diversity of liquid fertilizers and composts produced from the livestock manure in Korea is commonly applied to agricultural lands as an alternative of chemical fertilizers. However, their effects on the crop production and environmental impacts are still vague. The current study was investigated the property changes of paddy soils in sandy loam and silty loam treated with 1) control (no treatment), 2) chemicals, 3) storage liquid fertilizer and 4) SCB liquid fertilizer located in Gyeong-gi province, Korea. The chemical properties of soils in sandy loam and silty loam before the treatment were similar with the ones in the average paddy fields in Korea. Contrary to this, the amount of available phosphorus in sandy loam was higher than the one in the average paddy fields. The number of living organisms in sandy loam and silty loam treated with storage liquid fertilizer and SCB liquid fertilizer were higher than the ones in sandy loam and silty loam with no-treatment and chemicals. Significant difference (P<0.05) among the treatments and no-treatment was observed in sandy loam rather than in silty loam. The amounts of heavy metals were the highest in both sandy loam and silty loam treated with storage liquid fertilizer and SCB liquid fertilizer. The comparison of heavy metals showed that the ones in silty loam were little bit higher than sandy loam. The leaf lengths and dry weights of rices were increased over time, however, no significant difference was observed among each treament. In addition, the rice yield in sandy loam treated with SCB liquid fertilizer was higher than the ones in sandy loam. The highest rice yield was obtained from sandy loam treated with chemicals, but there was no significant difference between storage liquid fertilizer and SCB liquid fertilizer. While the rate of nutrient absorption by rices was the highest in sandy loam and silty loam treated with chemicals, there was no significant difference in sandy loam and silty loam treated with livestock liquid manure.