• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.3
• /
• pp.233-238
• /
• 2008

In this paper, a shape design optimization method for linearly elastic problems is developed using isogeometric approach. In many design optimization problems for practical engineering models, initial raw data usually come from a CAD modeler. Then, designers should convert the CAD data into finite element mesh data since most of conventional design optimization tools are based on finite element analysis. During this conversion, there are some numerical errors due to geometric approximation, which causes accuracy problems in response as well as design sensitivity analyses. As a remedy for this phenomenon, the isogeometric analysis method can be one of the promising approaches for the shape design optimization. The main idea of isogeometric approach is that the basis functions used in analysis is exactly the same as the ones representing the geometry. This geometrically exact model can be used in the shape sensitivity analysis and design optimization as well. Therefore the shape design sensitivity with high accuracy can be obtained, which is very essential for a gradient-based optimization. Through numerical examples, it is verified that the shape design optimization based on an isogeometic approach works well.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.14 no.3
• /
• pp.174-187
• /
• 2011

The flowed soil is able to be estimated from topographic data of before and after the debris flow. However, it is often difficult to obtain airborne LiDAR data before the debris flow area. Thus, this study tries to develop a topographic restoration method that can provide spatial distribution of flowed soil and reconstruct the topography before the debris flow using airborne LiDAR data. The topographic restoration method can express a numerical formula induced from a Gaussian mixture model after extracting the cross sections of linear or non-linear in debris flowed area. The topographic restoration method was verified by two ways using airborne LiDAR data of before and after the debris flow. First, each cross section extracted from the debris flow sites to restore the topography was compared with airborne LiDAR data of before the debris flow. Also, the topographic data produced after the topographic restoration method applied to the debris flow sites was verified by airborne LiDAR DEM. Verifying the results of the topographic restoration method, overall fitting accuracy showed high accuracy close to 0.5m.

• Composites Research
• /
• v.28 no.4
• /
• pp.204-211
• /
• 2015

This paper presents a theory related to a two-dimensional linear cross-sectional analysis, recovery relationship and a one-dimensional nonlinear beam analysis for composite wing structure with initial twist. Using VABS including a related theory, the design process of the composite rotor blade has been described. Cross-sectional analysis was performed at cutting point including all the details of geometry and material. Stiffness matrix and mass matrix were linked to each section to make 1D beam model. The 3D strain distributions within the structure were recovered based on the global behavior of the 1D beam analysis and visualize numerical results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.98-105
• /
• 2013

This paper presents a finite-difference time-domain(FDTD) simulation and a data processing technique for radar sensing of the internal structure of a wall using an ultra-wide band antenna. We first designed an ultra-wide band anti-podal vivaldi antenna with a frequency range of 0.3~7 GHz which is chosen to be relatively low after considering the characteristics of wave attenuation, wall penetration, and range resolution. In this study the two-dimensional FDTD technique was used to simulate a wall-penetration-radar experiment under practical conditions. The next, the measured radiation pattern of the practical antenna is considered as an equivalent source in the FDTD simulation, and the reflection data of a concrete wall and targets are obtained by using the simulation. Then, a data processing technique has been applied to the FDTD reflection data to get a radar image for remote sensing of the internal structure of the wall. We compared the two different source excitations in the FDTD simulation; (1) commonly-used isotropic point sources and (2) polynomial curve fitting sources of the measured radiation pattern. As a result, when we apply the measured antenna pattern into the FDTD simulation, we could obtain about 2.5 dB higher signal to noise level than using a plane wave incidence with isotropic sources.

• Progress in Medical Physics
• /
• v.16 no.1
• /
• pp.24-31
• /
• 2005

The stereotactic radiosurgery (SRS) describes a method of delivering a high dose of radiation to a small tar-get volume in the brain, generally in a single fraction, while the dose delivered to the surrounding normal tissue should be minimized. To perform automatic plan of the SRS, a new method of multi-isocenter/shot linear accelerator (linac) and gamma knife (GK) radiosurgery treatment plan was developed, based on a physical lattice structure in target. The optimal radiosurgical plan had been constructed by many beam parameters in a linear accelerator or gamma knife-based radiation therapy. In this work, an isocenter/shot was modeled as a sphere, which is equal to the circular collimator/helmet hole size because the dimension of the 50% isodose level in the dose profile is similar to its size. In a computer-aided system, it accomplished first an automatic arrangement of multi-isocenter/shot considering two parameters such as positions and collimator/helmet sizes for each isocenter/shot. Simultaneously, an irregularly shaped target was approximated by cubic structures through computation of voxel units. The treatment planning method by the technique was evaluated as a dose distribution by dose volume histograms, dose conformity, and dose homogeneity to targets. For irregularly shaped targets, the new method performed optimal multi-isocenter packing, and it only took a few seconds in a computer-aided system. The targets were included in a more than 50% isodose curve. The dose conformity was ordinarily acceptable levels and the dose homogeneity was always less than 2.0, satisfying for various targets referred to Radiation Therapy Oncology Group (RTOG) SRS criteria. In conclusion, this approach by physical lattice structure could be a useful radiosurgical plan without restrictions in the various tumor shapes and the different modality techniques such as linac and GK for SRS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5C
• /
• pp.413-421
• /
• 2008

The paper derives asymptotic formulas for the MSE distortion and the signal-to-noise ratio of a mismatched fixed-rate minimum MSE Laplacian quantizer. These closed-form formulas are expressed in terms of the number N of quantization points, the mean displacement $\mu$, and the ratio $\rho$ of the standard deviation of the source to that for which the quantizer is optimally designed. Numerical results show that the principal formula is accurate in that, for rate R=$log_2N{\geq}6$, it predicts signal-to-noise ratios within 1% of the true values for a wide range of $\mu$, and $\rho$. The new findings herein include the fact that, for heavy variance mismatch of ${\rho}>3/2$, the signal-to-noise ratio increases at the rate of $9/\rho$ dB/bit, which is slower than the usual 6 dB/bit, and the fact that an optimal uniform quantizer, though optimally designed, is slightly more than critically mismatched to the source. It is also found that signal-to-noise ratio loss due to $\mu$ is moderate. The derived formulas can be useful in quantization of speech or music signals, which are modeled well as Laplacian sources and have changing short-term variances.

• Applied Biological Chemistry
• /
• v.22 no.2
• /
• pp.101-108
• /
• 1979

The viscosity of mucilage of Abelmoschus Manihot, Medic root decreased by the influence of various mechanical, physical and chemical conditions. It was experimented by viscosity decrease of mucilage connected with hydrogen ion concentration, bacterial multiplication, disinfection with 70% ethanol, some antibiotics, such as streptomycin, penicillin, ganamycin and chloramphenicol and mucilage derived from autoclaved Abelmoschus Manihot, Medic root. The results obtained were as follows: 1. It was clear that the viscosify of mucilage decreased notably under the influence of infected bacteria and bacterial multiplication. 2. By the inoculation of Bacillus subtilis ATCC 6633 and Escherichia coli ML 1410 to the mucilage the viscosify decrease fast but the viscosity of mucilage derived from autoclaved, Abelmoschus Manihot, Medic root. 3. The small quantity of reducing sugar in the mucilage was detected. 4. Hydrogan ion concentration in the mucilage remained $6.5{\sim}8.0$ in spite of the viscosity decrease.

• Journal of Navigation and Port Research
• /
• v.36 no.5
• /
• pp.371-378
• /
• 2012

This paper presents a timing recovery method using Gardner TED (Timing Error Detector) with a Peak Detector using Parabola Peak Interpolation in underwater acoustic communication. This method will have an eye to improve phase converge speed of timing recovery and reduced amount of Tx data. The OQPSK(Offset Quadrature Phase Shift Keying) modulation technique was considered. The proposed algorithm has faster recovery speed and more accurate than Gardner TED because the sampling values in the proposed algorithm are moved persistingly to maximum or minimum point using parabolic peak interpolation. when simulation performed using Preposed method, it improved BER (Bit Error Rate) performance about 23% And to evaluate the performances of the proposed algorithm the sea trial was performed in the Korean East Sea. And distance of a transmitter-receiver is 3 km each other. As a result, the proposed algorithm outperforms better BER performance about 20% of timing recovery than the Gardner method. Also Proposed method improved converge speed of timing recovery about 1.4 times better than Gardner method.

• Journal of the KSME
• /
• v.27 no.6
• /
• pp.504-514
• /
• 1987

복잡한 전자부품의 조립시에 필요한 열적 디자인에 관한 정보는 오래전부터 실험을 통하여 얻어지고 있다. 실험적 데이터를 이용하여 무차원 파라미터로 표시된 실험결과는 꼭 같지는 않지만 현상적으로는 비슷한 상황에 응용될 수 있다. 여기서는 학술문헌에 나타나 있는 자연대류에 관한 실험적인 상관관계식들과 프레임에 수직으로 꽂혀있는 균일가열 전자회로기판의 모델에서 얻어진 무차원 자료들을 비교하고자 한다. 대부분의 자료들은 수정채널 Rayleigh수(Ra")가 15~100범위에 속하며, 이러한 범위는 부품이 조밀하게 배치된 기관이 서로 좁은 채널을 이루고 있으며, 동시에 상당한 전력을 소비하고 있는 경우에 해당한다. Wirt와 Stutzman, Bar-Cohen과 Rohsenow의 일반상관관계식은 AT'||'&'||'T Bell 연구소에서 개발된 전자기기를 이용하여 수집한 실험데이터를 잘 표현하고 있으며 10 < Ra" <1,000범위에서 추천될 수 있다. 두개의 유사한 상관관계식과 비교할 때 상당히 좋은 예측을 보였으며 또한 Sparrow와 Gregg의 연구결과와도 잘 일치하므로 Ra" < 10인 경우에 Aung의 완전발달층류의 채널유동방식, Ra" > 1,000인 경우에는 Aung등의 단일 수직평판 근사식이 추천될 수 있다. Coyne의 알고리즘에 의한 계산치는 10

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.32-32
• /
• 2011

최근 국내외에서 친환경건축물에 관한 관심이 매우 높아짐으로 인해 콘크리트의 물량을 절감하여 이산화탄소량을 줄이는 중공슬래브는 다양한 형태로 세계적으로 개발이 되고 있는 추세이다. 특히 이방향 중공슬래브는 환경적인 측면에서 이방향 중공슬래브는 중공부 생성에 재생플라스틱을 활용하여 폐자원을 재사용하고, 콘크리트와 철근의 사용량 절감에 따른 화석에너지 및 이산화탄소 발생량을 감소한다는 장점이 있다. 또한 시스템 측면에서 이방향 중공슬래브는 기존의 철근콘크리트 플랫플레이트 바닥구조 시스템의 자중을 절감하여 구조체를 경량화 시키고, 이에 따라 장스팬 구현이 가능하며, 단열효과가 뛰어나다. 이와 같이 이방향 중공슬래브는 장점이 많지만 플랫플레이트 슬래브의 취약점인 뚫림전단 파괴에 주의해야 한다. 이에 본 연구에서는 선행으로 실시된 이방향 중공슬래브-기둥 접합부 뚫림전단 성능평가 실험을 바탕으로 하여 경량체가 이방향 중공슬래브-기둥 접합부 뚫림전단 성능에 미치는 영향을 살펴보기 위해 범용 유한요소해석 프로그램인 ABAQUS를 사용하여 경량체량 및 위치를 주요변수로 한 해석적인 변화를 검토하였다. 본 연구를 통해 경량체가 삽입된 이방향 중공슬래브의 뚫림전단 성능에 대해, 해석결과 경량체 량과 위치에 따라 최대 뚫림전단강도는 기준 실험체에 비해 74.3%, 73%의 강도저하를 나타내는 것으로 알 수 있었다. 이는 실험상의 강도저하 값인 84.1%, 56.4%와 다소 차이가 있으며, 해석에서 중공부 주위의 응력집중 현상이 제대로 반영되지 않은 것으로 판단된다. 또한 이방향 슬래브에 경량체를 삽입 할 경우 경량체가 시작하는 부분에서 응력이 급격히 감소하는 현상이 나타났으며, 이러한 급격한 응력감소는 기둥 주위 위험단면의 변화를 가져오는 것으로 추정된다. 즉, 위험단면의 변화는 기둥으로부터 경량체 사이의 거리에 따라 달라지며, 위험단면 내의 콘크리트 단면 손실은 뚫림전단 강도를 감소시킨다. 본 연구에서는 이방향 중공슬래브의 뚫림전단강도를 산정할 수 있는 근사식을 제안하였으며, 보다 정확한 이방향 중공슬래브의 뚫림전단강도의 산정식을 위해서는 위험단면의 변화와 콘크리트 단면손실로 인한 전단강도 저하의 관계에 대한 추가적인 연구가 필요하다.