• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.3 s.151
• /
• pp.447-457
• /
• 2006

The purpose of this study is to document and preserve an unidentified textile purchased at a flea market. This study object is important because it is one of the very rare silk insert series from 1930s which were created for commercial use(as inclusion in cigarette packages). The investigation was conducted by researching the limited publications that discuss silk inserts, visiting many sites on the internet that offer such inserts for sale or catering to the collectors of these silk inserts, and especially visiting the collection of silk inserts, named the J.R. Burdick Collection, at the Metropolitan Museum of Art, New York. Several pieces matched the patches used in the study piece. But Buidick's description on time frame(1912-1915) did not indicate the full range of production of silk inserts. After the identification of object, the conservation treatment was carefully done using adhesives. The results of this study can be summarized as follows; 1. The silk inserts of the study object were included as promotions by some company owned by the American Tobacco Company, probably at some time between 1934 and 1939. 2. The initial stage in the conservation treatment was mechanical surface cleaning using a vacuum cleaner. After vacuuming, humidification was conducted to reduce creases in the top of the object. The damaged areas were backed with stabiltax coated with a solution of Elvace 45675 since the fiber of this object was too deteriorated. 3. Adhesive treatments using Elvace showed satisfactory results: flexibility, strength, no damaging effects on the study object, removability without damaging the object.

• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.99-104
• /
• 2011

Currently, automotive pre-primed coatings has been developed to overcome environmental regulations and to reduce manufacturing cost in automotive industry. By these reasons, an automotive pre-primed system has been investigated to remove the wash and pre-treatment process using a roll coating application. It is required to develop non-weldable pre-primed system for automotive structural adhesives, because pre-primed sheet coated with organic compounds is hard to be assembled by welding process. Primer 1 (polyester type) and primer 2 (urethane type) were designed to satisfy flexibility and formability for non-weldable pre-primed system. According to the results of physical property test of the primers, adhesion test such as single-lap shear test and T-peel test, primer 1 (polyester type) had better physical properties such as pencil hardness, solvent resistance, flexibility and adhesion with automotive adhesive than that of primer 2 (polyurethane type). In addition, the possibility of the non-weldable pre-primed system was applicable to automotive assembly process in place of welding process.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1A
• /
• pp.11-18
• /
• 2012

This paper deals with the numerical determination of the stress intensity factors of cracked aluminum plates under the mixed mode of $K_I$ and $K_{II}$ in glass-epoxy fiber reinforced composites. For the stress intensity factors, two different models are reviewed such as VCCT and two-step extension method. The p-convergent partial layerwise model is adopted to determine the fracture parameters in terms of energy release rates and stress intensity factors. The p-convergent approach is based on the concept of subparametric element. In assumed displacement field, strain-displacement relations and 3-D constitutive equations of a layer are obtained by combination of 2-D and 1-D higher-order shape functions. In the elements, Lobatto shape functions and Gauss-Lobatto technique are employed to interpolate displacement fields and to implement numerical quadrature. Using the models and techniques considered, effects of composite laminate configuration according to inclined angles and adhesive properties on the performance of bonded composite patch are investigated. In addition to these, the out-of-plane bending effect has been investigated across the thickness of patch repaired laminate plates due to the change of neutral axis. The present model provides accuracy and simplicity in terms of stress intensity factors, stress distribution, number of degrees of freedom, and energy release rates as compared with previous works in literatures.

• Restorative Dentistry and Endodontics
• /
• v.34 no.6
• /
• pp.467-476
• /
• 2009

The aim of this study was to measure the dentinal tubular fluid flow (DFF) during and after amalgam and composite restorations. A newly designed fluid flow measurement instrument was made. A third molar cut at 3 mm apical from the CEJ was connected to the flow measuring device under a hydrostatic pressure of 15 $cmH_2O$. Class I cavity was prepared and restored with either amalgam (Copalite varnish and Bestaloy) or composite (Z-250 with ScotchBond MultiPurpose: MP, Single Bond 2: SB, Clearfil SE Bond: CE and Easy Bond: EB as bonding systems). The DFF was measured from the intact tooth state through restoration procedures to 30 minutes after restoration, and re-measured at 3 and 7days after restoration. Inward fluid flow (IF) during cavity preparation was followed by outward flow (OF) after preparation, In amalgam restoration, the OF changed to IF during amalgam filling and slight OF followed after finishing. In composite restoration, application CE and EB showed a continuous OF and air-dry increased rapidly the OF until light-curing, whereas in MP and SB, rinse and dry caused IF and OF, respectively. Application of hydrophobic bonding resin in MP and CE caused a decrease in flow rate or even slight IF. Light-curing of adhesive and composite showed an abrupt IF. There was no statistically significant difference in the reduction of DFF among the materials at 30 min. 3 and 7 days after restoration (p > 0.05).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.3
• /
• pp.422-428
• /
• 2006

Dentin bonding system have recently been developed in an effort to simplify and shorten bonding procedure. The intent of this study was to evaluate microleakage of newer generation of dentin bonding system comparing with other generations. Forty extracted human premolar teeth were randomly assigned to four groups for bonding : the 4th generation bonding system (Scotchbond Multi-Purpose). the 5th generation bonding system (Clearfil SE Bond), 6th generation bonding system (AQ bond) and 7th generation bonding $system(i-bond)^{TM}$ Class V cavities were prepared in buccal and lingual surface. The cavities were restored with composite resin (Z100) after the application of dentin bonding systems according to the instructions of the manufacturer Samples were thermocycled and immersed in methylene blue dye(2%). Each sample was sectioned with Isomet and evaluated for microleakage using stereomicroscopy. The mean value of the microleakage in 7th generation bonding system was greater than those of 4, 5, 6th generation dentin bonding system. Statistically, the mean values of microleakage between 4th and 7th generation bonding system were significantly different from each other (p<0.05).

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.22-29
• /
• 2005

This research was carried out not only to examine the proper manufacturing condition for white charcoal board in relation to charcoal particle size and final mat moisture content (FMC), but also to maintain the advantageous properties of white charcoal as a well being building material against the sick house problem. Excellent functional white charcoal board was produced with two groups of FMC 20~25% and FMC 36~60%. The latter showed best results among tested samples in two types which are #40-60type-P15%, M5%, FMC 60% and mixed type-P15%, M5%, FMC36% with non formaldehyde adhesives [MDI (M), poly vinyl acetate emulsion (P)] and three stage pressing cycle of 30-10-$30kgf/cm^2$ (1 min.-1.5 min.-6 min.). The former gave highly acceptable results in two types which are #6 over-M15%FMC25% and mixed type-M25%FMC20%. White charcoal board gave excellent in dimensional stability, gas adsorption and far-infrared emission.

• Restorative Dentistry and Endodontics
• /
• v.29 no.2
• /
• pp.162-169
• /
• 2004

This study evaluated the marginal microleakage of five single step adhesives. Class V cavity preparations with occlusal margins in enamel and gingival margins in dentin were prepared on both buccal and lingual surfaces of extracted human molar teeth. Prepared teeth were randomly divided into five groups and restored using one of the single step adhesives and composite resins：Prompt L-Pop/Filtek Z-250 (Group 1), AQ Bond/Metafil CX (Group 2), One-Up Bond F/Palfique Toughwell (Group 3). Futurabond/Admira (Group 4), Xeno III/Spectrum TPH (Group 5). The restored teeth were thermocycled. Microleakage was assessed by dye penetration using 2% methylene blue dye solution. The teeth were bisected buccolingually and evaluated for microleakage under steromicroscope. The data were statistically analysed by Kruskal-Wallis test and Mann-Whitney tests. The results of this study were as follows：1. Microleakage of enamel margins in group 3 was statistically higher than that in groups 1, 2, 4, 5 (p < 0.05). 2. Microleakage of dentin margins in group 1 was statistically higher than that in groups 2, 5, and that in group 3 was statistically higher than that in groups 2, 4, 5 (p < 0.05). 3. Dentin marginal microleakage was higher than enamel marginal microleakage in all experimental groups. In conclusion, Prompt L-Pop showed the least leakage at enamel margin, and AQ Bond showed at dentin margin in this study. Marginal miroleakage in dentin was higher than that in enamel.

• Restorative Dentistry and Endodontics
• /
• v.31 no.5
• /
• pp.337-343
• /
• 2006

The purpose of this study was to estimate the relation between techniques used for microleakage from dye penetration and for marginal adaptation from SEM evaluation of the restoration. Using high speed #330 bur class V cavities ($4{\times}3{\times}1.5 mm$ around CEJ) were prepared on the buccal surface of 20 extracted human molars. Six dimples as reference points for SEM and dye penetration evaluation were made with 1/2 round bur. Cavity was bulk filled with microhybrid composite resin (Esthet X) and all-in-one adhesive (Xeno III). Teeth were stored in saline solution for one day, after then, they were finished and polished using Sof-Lex system. Fifty percent silver nitrate dye solution was used for the evaluation of microleakage and resin replica was used for marginal adaptation. All of these were done after 1000 times thermocycling between 5 and $55^{\circ}C$. Vertical sections were made through three dimples of restoration to obtain samples for the evaluation of dye penetration and inner marginal adaptation. Outer adaptational estimation was done with an intact restoration before sectioning. Dye penetration was determined in three degrees and percentage of outer and inner leaky margin was estimated from SEM image The data were analysed statistically: Spearman's rho test were used to check relationships between two methods. The result were as follows : 1. There were significant relationships between degree of dye penetration and inner and outer marginal adaptations each (p < 0.01). 2. However, there was no significant relationship between the results or inner and outer marginal adaptation. Within the results of this study, relationship between the percentage of marginal adaptation and microleakage shows significant relationship. However, inner and outer marginal adaptation did not show any significant relationship mutually.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.325-332
• /
• 2004

A self-etching primer that combines the etchant and primer in one chemical compound saves time and should be mote cost-effective to the clinician and patient. The purpose of this study was to evaluate the clinical effectiveness of a self-etching primer by measuring shear bond strengths according to various conditions and observing adhesive failure patterns. For this Investigation, 120 upper and lower premolars extracted for orthodontic purposes were used and randomly divided into six groups of twenty teeth each. Human premolars were embedded in a metal cylinder with orthodontic resin. Metal brackets and ceramic brackets were bonded with XT primer and self-etching primer by means of XT adhesive. Upon curing, plasma arc light and visible light were used. After bonding, the shear bond strength was tested by Instron universal testing machine, and the amount of residual adhesive that remained on the tooth after debonding was measured by stereoscope and assessed with an adhesive remnant index. The results were as fellows: 1. When brackets were bonded, if other conditions remained the same, there was no significant difference in shear bond strength due to the type of primer - either self-etching primer or XT primer. 2. When metal brackets were bonded, there was no significant difference in shear bond strength according to the source of light - plasma arc light or visible light - and type of primer. 3. There was a very significant difference in shear bond strength according to the type of brackets - metal or ceramic brackets. The shear bond strength of ceramic brackets was stronger than metal brackets. 4. When the adhesive failure patterns of metal brackets bonded with self-etching primer were observed by using the adhesive remnant index, the bond failure of the metal bracket occurred more frequently at the bracket-adhesive. The failure of the ceramic bracket, however, occurred more frequently at the enamel-adhesive interface. The adhesive failure patterns of metal brackets bonded with XT primer observed the same patterns. The above results suggest that self-etching primer can be clinically useful for bonding the brackets without fear of a decrease in shear bond strength.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2007.05a
• /
• pp.281-299
• /
• 2007

IS/IT 분야 실무자가 지니고 있어야 한다고 생각되는 지식과 전문 기술들을 '지식/능력 영역'과 '소프트웨어 전문 기술 영역'으로 구분하여 각각 세부 항목을 명세하였다. 그리고 분류된 두 영역에 대하여 IS/IT 분야 실무자가 생각하는 필요한 지식 및 전문 기술들의 중요도와 IS/IT 전공 교수가 생각하는 IS/IT 실무자에게 필요한 지식 및 전문 기술들의 중요도를 조사하여 두 그룹간의 인식차 비교를 시도하였다. 조사지역은 실무자는 충청지역 및 수도권 지역에 분포하는 SI 업체를 대상으로 이루어 졌다. IS/IT 실무자를 대상으로 한 조사는 실무자 본인의 일장에서 IS/IT 실무자가 갖추어야 된다고 판단되는 지식 및 전문 기술들의 중요도를 측정하였다. 그와 더불어 그들이 수행하는 IS 활동에 대하여 투자한 시간을 기준으로 군집분석을 실시하여 세가지 그룹으로 구분하여 실무자 전체와 세 그룹간의 비교가 가능하도록 조차되었다. 비교 결과, 지식/능력 영역에서는 IS 실무자들이 상대적으로 '하드웨어에 대한 지식', '특정 조직', '운영체제에 대한 지식'에 대해 더 높은 중요도를 부여하고 있는 것으로 나타났다. 소프트웨어 전문 기술 영역에서는 실무자보다 전공교수가 생각하는 중요도가 보편적으로 더 높게 나타났다. 전공 교수는 '프리젠테이션 도구', '객체지향 언어(C++, Java 등)'에 4점 대의 높은 점수를 주어 중요한 것이 무엇인가 하는 인지가 있는 것으로 보이나 실무자 그룹에서는 특별히 중요시 여기는 항목이 명확히 드러나지 않고 보편적인 값이 median 값 주변에 위치하고 있다. 이는 현재 실무자들이 빠르게 변화하고 있는 IS/IT 환경에서 본인의 경력경로 (career path)을 위해 무엇이 중요한 갓인지 아직 명확히 하고 있지 못하는 것으로도 해석이 가능하다. 자세한 비교/분석 및 해석은 현재 진행 중이며, 여러 흥미로운 해석이 가능할 것으로 기대 된다.합형 파괴가 증가하는 경향을 나타내었다. 이상의 결과로, 상아질 접착제의 접착단계/과정이 결합내구성에 영향을 미침을 알 수 있었다. 따라서 접착과정의 단순화가 반드시 접착에 효과적이라고 할 수 없다.는 저작 운동 잔에는 2군에서 Heliomolar가 Pyramid보다 변연적합도가 우수하였고 (p < 0.05) 그 외의 군에서는 유의차가 없었으며, 저작 운동 후에는 모든 군에서 재료간 유의차가 없었다. 각 부위별 변연적합도를 비교하면, 저작 운동 전 Pyramid에서는 교합면 변연에서는 4군이 2군에 비해 높은 변연적합도를 보였고 (p < 0.05), 인접면과 치은면에서는 군 간 유의차를 보이지 않았다. Heliomolar에서는 교합면 변연에서 2, 4군이 1군에 비해 높은 변연적합도를 보였고 (p < 0.05), 인접면과 치은면에서는 군간 유의차를 보이지 않았다. 저작 운동 후 Pyramid에서는 교합면 변연에서는 3군이 1, 2군에 비해 높은 변연적합도를 보였고 (p < 0.05), 인접면과 치은면에서는 군간 유의차를 보이지 않았다. Heliomolar에서는 교합면에서 2, 3, 4군이 1군에 비해 변연적합도가 높았으며 (p < 0.05), 인접면과 치은면에서는 군간 유의차를 보이지 않았다 이번 연구를 통하여 복합레진을 간헐적 광중합시킴으로써 변연적합도가 향상될 수 있음을 알 수 있었다.시장에 비해 주가가 비교적 안정적인 수준을 유지해 왔다고 볼 수 있다.36.4%)와 외식을 선호(29.1%)${\lrcorner}$ 하기 때문에 패스트푸드를 이용하게 된 것으로 응답 하였으며, 남 여 대학생간에는 유의한 차이(p<0.05)가 인정되었다. 응답자의 체형은 ${\ulcorner}$적당하다${\lrcorner}$고 응답한 경우가 가장 많이 이러한 음식을 즐겨 먹었으며(49.5%), 그 다음은 뚱뚱한 경우도 비교적 많이 먹고