• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.2
• /
• pp.301-310
• /
• 2007

Bidirectional DC-DC converters allow transfer of power between two dc sources, in either direction. Due to their ability to reverse the direction of flow of power, Dey are being increasingly used in many applications such as battery charge/dischargers, do uninterruptible power supplies, electrical vehicle motor drives, aerospace power systems, telecom power supplies, etc. This Paper Proposes a new bidirectional Sepic/Zeta converter. It has low switching loss and low conduction loss due to auxiliary communicated circuit and synchronous rectifier operation, respectively Because of positive and buck/boost-like DC voltage transfer function(M=D/1-D), the proposed converter is very desirable for use in distributed power system. The proposed converter also has both transformer-less version and transformer one.

• International Journal of Computer Science & Network Security
• /
• v.23 no.9
• /
• pp.8-16
• /
• 2023

In Japan, high-speed ground transportation service using linear motors at speeds of 500 km/h is scheduled to begin in 2027. To accommodate 5G services in trains, a subcarrier spacing frequency of 30 kHz will be used instead of the typical 15 kHz subcarrier spacing to mitigate Doppler effects in such high-speed transport. Furthermore, to increase the cell size of the 5G mobile system, multiple base station antennas will transmit identical downlink (DL) signals to form an expanded cell size along the train rails. In this situation, the forward and backward antenna signals are Doppler-shifted in opposite directions, respectively, so the receiver in the train may suffer from estimating the exact Channel Transfer Function (CTF) for demodulation. In a previously published paper, we proposed a channel estimator based on Delay and Doppler Profiler (DDP) in a 5G SISO (Single Input Single Output) environment and successfully implemented it in a signal processing simulation system. In this paper, we extend it to 2×2 MIMO (Multiple Input Multiple Output) with spatial multiplexing environment and confirm that the delay and DDP based channel estimator is also effective in 2×2 MIMO environment. Its simulation performance is compared with that of a conventional time-domain linear interpolation estimator. The simulation results show that in a 2×2 MIMO environment, the conventional channel estimator can barely achieve QPSK modulation at speeds below 100 km/h and has poor CNR performance versus SISO. The performance degradation of CNR against DDP SISO is only 6dB to 7dB. And even under severe channel conditions such as 500km/h and 8-path inverse Doppler shift environment, the error rate can be reduced by combining the error with LDPC to reduce the error rate and improve the performance in 2×2 MIMO. QPSK modulation scheme in 2×2 MIMO can be used under severe channel conditions such as 500 km/h and 8-path inverse Doppler shift environment.

• International Journal of Aeronautical and Space Sciences
• /
• v.5 no.2
• /
• pp.35-42
• /
• 2004

Among other critical conditions in rotor svstems the large non-linearvibration excited by bearing non-linearity causes the rotor failure. For reducing thiscatastrophic failure and predictive analysis of this phenomena the identificationanalysis of bearing non-linearity in an anisotropic rotor system using the higherorder dFRFs are developed and are shown to be theoretically feasible as innon-rotating structures. For the identification of the anisotropic rotor withanisotropic bearing non-linearity expressed by the displacement in polynomial form,the higher order dFRFs based upon the Volterra series are investigated and depicttheir features by using the simple forms of the normal and reverse dFRFs. Theyproduce additional sub-harmonic resonant peaks, which indicate the existence ofhigher order non-linearties, and show the energy transfer such that the modes fornormal and reuerse dFRFs are exchanged, which are the fundamental differencesfrom what we can expect in linear ones.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.1
• /
• pp.49-58
• /
• 1999

This paper describes an integrated low pass filter fabricated by using $0.8{\mu}m$ single poly CMOS ASIC technology. The filter has been designed for a 5th-order elliptic switched capacitor filter with cutoff frequency of 5khz, 0.1dB passband ripple. The filter consists of MOS swiches poly capacitors and five CMOS op-amps. For the realization of the SC filter, continuous time transfer function H(s) is obtained from LC passive type, and transfered as discrete time transfer H(z) through bilinear-z transform. Another filter has been designed by capacitor scaling for reduced chip area, considering dynamic range of the op-amp. The test results of two fabricated filters are cutoff frequency of 4.96~4.98khz, 35~38dB gain attenuation and 0.72~0.81dB passband ripple with the ${\pm}2.5V$power supply clock of 50KHz.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.19 no.4
• /
• pp.297-308
• /
• 2003

Face-bow is used to transfer models to the articulator in diagnosing the patient or treating problems associated with occlusion. However, there have been few reports on the reliability of the face-bow procedure and the relationship between the experience of the operator and the reliability of the face-bow procedure. The purposes of this study are to examine the reliability of the face-bow procedure and to evaluate whether the face-bow transferring has any training effect. Nine dentists working at M hospital conducted a face-bow transfer in one patient having a normal dentition and interdental relationship. The procedure was done two times a week for four weeks. The maxillary model was mounted to the articulator every time, then the landmarks on the maxillary right first molar, the maxillary left central incisor, and the maxillary left first molar were measured with a special three-dimensional instrument. These data were input into a computer, and evaluated statistically. The results were as follows ; 1. When examined with ANOVA test, the results were p=0.2040 in maxillary right first molar, p=0.0578 in maxillary left incisor, and p=0.1433 in maxillary left first molar. There was no significant(0< $p{\leq}0.05$). 2. Training 1) The correlation coefficient between trial and rejection was -0.578 when analyzed with T-distribution. The more we tried, the less errors we found. 2) When the S.D. of the first three trials was compared to the S.D. of the last three trials in face-bow transfer, the results showed that the former was larger than the latter in thirty-nine times, and the latter was larger than the former in fifteen times. The more we tried face-bow transfer, the less errors we found. 3. When the S.D. of x, y, z coordinates were examined, the S.D. of x coordinates had the largest measurement in five times, the S.D. of y coordinates had the largest measurement in four times, and the S.D. of z coordinates had the largest measurement in nine times. The possibility which the error can occur in z coordinate was the highest.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.2
• /
• pp.209-219
• /
• 2010

In this paper, a novel dynamic available transfer capability (DATC) has been computed for real time applications using three different intelligent techniques viz. i) back propagation algorithm (BPA), ii) radial basis function (RBF), and iii) adaptive neuro fuzzy inference system (ANFIS) for the first time. The conventional method of DATC is tedious and time consuming. DATC is concerned with calculating the maximum increase in point to point transfer such that the transient response remains stable and viable. The ATC information is to be continuously updated in real time and made available to market participants through an internet based Open Access Same time Information System (OASIS). The independent system operator (ISO) evaluates the transaction in real time on the basis of DATC information. The dynamic contingency screening method [1] has been utilized and critical contingencies are selected for the computation of DATC using the energy function based potential energy boundary surface (PEBS) method. The PEBS based DATC has been utilized to generate patterns for the intelligent techniques. The three different intelligent methods are tested on New England 68-bus 16 machine and 39-bus 10 machine systems and results are compared with the conventional PEBS method.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.6
• /
• pp.195-207
• /
• 2017

Since the smart phone was first introduced, the amount of mobile traffic has increased explosively. The OTT service with personal broadcasting and TV contents and the number of users have been increased in wired network, and there are needs to expand the OTT service to mobile network. In the case of the OTT service in mobile network, the relative small and finite resource may cause the overload of the network due to the massive and high transfer rate. In this paper, we consider a future situation of the OTT user services in the cellular network and propose a novel D2D communication scheme for location-based OTT service, which can reduce and distribute the amount of video traffics. To effectively handle the traffic of OTT services, we propose D2DS and LCS functional blocks in EPC network, which can provide location-based service and D2D management. And, we suggest additional procedures for the location-based service of both content provider and contents receiver UEs with the operation of the proposed D2DS and LCS function block.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.629-634
• /
• 2000

This System is developed for the estimation of the Camera Lens Resolution. Signal data proportional to light intensity is obtained and sampled from the 2D CCD. Based on the measured signal. the MTF charateristcs of a camera lens are measured. We could measure the sagittal and tangential MTF in the on and off-axis at the same time. The automatic measurig methods for optimal image plane, magnification, and best marginal direction of test lens are presented.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.62-65
• /
• 2002

A dieless forming system which consists of hydraulic punch elements and elastomer/fluid pads, was developed for sheet metal forming. 2-D curved surface forming was carried out using open-loop, closed-loop, and repeated forming method. Closed-loop exhibited higher decision than open-loop forming. Repeated forming also showed reduced spring back and possibility of high precision.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2577-2582
• /
• 2013

A novel stick-shaped portable sensing device featuring a microhole array interface between the polyvinylchloride-2-nitrophenyloctylether (PVC-NPOE) gel and water phase was developed for in-situ sensing of perchlorate ions in real water samples. Perchlorate sensitive sensing responses were obtained based on measuring the current changes with respect to the assisted transfer reaction of perchlorate ions by a perchlorate selective ligand namely, bis(dibenzoylmethanato)Ni(II) (Ni(DBM)2) across the polarized microhole array interface. Cyclic voltammetry was used to characterize the assisted transfer reaction of perchlorate ions by the $Ni(DBM)_2$ ligand when using the portable sensing device. The current response for the transfer of perchlorate anions by $Ni(DBM)_2$ across the micro-water/gel interface linearly increased as a function of the perchlorate ion concentration. The technique of differential pulse stripping voltammetry was also utilized to improve the sensitivity of the perchlorate anion detection down to 10 ppb. This was acquired by preconcentrating perchlorate anions in the gel layer by means of holding the ion transfer potential at 0 mV (vs. Ag/AgCl) for 30 s followed by stripping the complexed perchlorate ion with the ligand. The effect of various potential interfering anions on the perchlorate sensor was also investigated and showed an excellent selectivity over $Br^-$, $NO_2{^-}$, $NO_3{^-}$, $CO{_3}^{2^-}$, $CH_3COO^-$ and $SO{_4}^{2^-}$ ions. As a final demonstration, some regional water samples from the Sincheon river in Daegu city were analyzed and the data was verified with that of ion chromatography (IC) analysis from one of the Korean-certified water quality evaluation centers.