• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.42 no.3
• /
• pp.224-231
• /
• 2009

Volatile components in Olive Flounder fed diets containing 0, 2,5, 5.0, and 7.5% yuza (Citrus junas Sieb ex Tanaka) for 4 months were investigated. Samples were extracted by solid-phase micro extraction and analyzed by gas chromatography/mass spectrometry. Among 89 compounds detected, 82 were positively identified. Volatile compounds of Olive Flounder fed the unsupplemented diet comprised 12 acids, 10 alcohols, eight aldehydes, five aromatic compounds, nine esters, 12 hydrocarbons, four ketones, two monoterpenes, and one miscellaneous compound. Compounds identified in Olive Flounder fed the yuza-supplemented diets consisted of 10 esters, 11 monoterpenes, 13 sesquiterpenes, and two miscellaneous compounds, with the other compounds being the same as in the control. The most abundant class of compounds in flounders fed the yuza-supplemented diet was the monoterpenes, which included limonene, $\beta$-terpinene, $\beta$-trans-ocimene, and $\alpha$-terpinolene. Of the 13 sesquiterpenes identified in flounder fed the yuza-supplemented diet, bicyclogermacrene was the major volatile compound followed by allo-aromadendrene, trans-caryophyllene, and $\delta$-cadinene. Bicyclogermacrene and germacrene D content increased significantly as the yuza supplementation increased.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.49 no.6
• /
• pp.47-54
• /
• 2007

This paper is on the research of the special character of the dynamic response according to a design of the clamped reinforced concrete slab. In this study, the 20-node solid element has been used to analyze the dynamic characteristics of RC slabs with clamped edges. The elasto-visco plastic model for material non-linearity and the smeared crack model have been adopted in the finite element formulation. The design factor, which affect the dynamic response of the reinforced concrete slab, are the steel layer thickness, steel layer depth, steel layout method, steel layout angle and the slab thickness and span ratio. The main purpose of this study was to find out the dynamic response of the reinforced concrete slab according to above variables. The reduction of deflection/thickness ratio appeared less than 2% when the slab thickness between 20 and 21cm. It is desirable that the slab thickness must be above 20-21cm. The reduction ratio of deflection is appeared greatly when the value of the span/thickness ratio is between 25 and 30. In conclusion, the steel layer depth and thickness had a little effect on deflection of the dynamic response, but had no effect on the steel layout angle.

• Journal of the Korean Magnetic Resonance Society
• /
• v.20 no.4
• /
• pp.129-137
• /
• 2016

Transmembrane(TM) proteins are closely related to transport, channel formation, signaling, cell to cell interaction, so they are the crucial target of modern medicinal drugs. In order to study the structure and function of these TM proteins, it is important to prepare reasonable amounts of proteins. However, their preparation is seriously difficult and time-consuming due to insufficient yields and low solubility of TM proteins. We tried to produce large amounts of Syndecan-4 containing TM domain(SDC4-TM) that is related to the wound healing and tumor. Also, mutated SDC4-TM was studied to investigate structural change by modification of dimerization motif. We performed the structure determination by the Polarity Index at Slanted Angle (PISA) wheel pattern analysis based on $^{15}N-^1H$ 2D SAMPI-4 solid-state NMR of SDC4-TM and computational modeling using Discovery Studio 2016.

• Computers and Concrete
• /
• v.3 no.1
• /
• pp.65-77
• /
• 2006

This study reports the details of the finite element analysis of eleven shear critical partially prestressed concrete T-beams having steel fibers over partial or full depth. Prestressed concrete T-beams having a shear span to depth ratio of 2.65 and 1.59 and failing in the shear have been analyzed using 'ANSYS'. The 'ANSYS' model accounts for the nonlinear phenomenon, such as, bond-slip of longitudinal reinforcements, post-cracking tensile stiffness of the concrete, stress transfer across the cracked blocks of the concrete and load sustenance through the bridging of steel fibers at crack interface. The concrete is modeled using 'SOLID65'-eight-node brick element, which is capable of simulating the cracking and crushing behavior of brittle materials. The reinforcements such as deformed bars, prestressing wires and steel fibers have been modeled discretely using 'LINK8' - 3D spar element. The slip between the reinforcement (rebar, fibers) and the concrete has been modeled using a 'COMBIN39'-non-linear spring element connecting the nodes of the 'LINK8' element representing the reinforcement and nodes of the 'SOLID65' elements representing the concrete. The 'ANSYS' model correctly predicted the diagonal tension failure and shear compression failure of prestressed concrete beams observed in the experiment. The capability of the model to capture the critical crack regions, loads and deflections for various types of shear failures in prestressed concrete beam has been illustrated.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.3
• /
• pp.329-336
• /
• 2008

The pilot study was conducted to evaluate the applicability of air flotation(AF) processes combined with biological nutrient removal(BNR) for the retrofitting of conventional wastewater treatment facilities. The BNR system was operated in pre-denitrification and intermittent aeration; developed ceramic membrane diffusers were installed to separate the solid-liquid of activated sludge at the bottom of a flotation tank. Before performing a pilot scale study, the size distribution of microbubbles generated by silica or alumina-based ceramic membrane diffusers was tested to identify the ability of solid-liquid separation. According to the experimental results, the separation and thickening efficiency of the alumina-based ceramic membrane diffuser was higher than the silica-based ceramic membrane diffuser. In a $100m^3/d$ pilot plant, thickened and return sludge concentration was measured to be higher than 15,000mg SS/L, therefore, the MLSS in the bioreactor was maintained at over 3,000mg SS/L. The effluent quality of the AF-BNR process was 4.2mg/L, 3.7mg/L, 10.6mg/L and 1.6mg/L for $BOD_5$, SS, T-N and T-P, respectively. Lastly, it was revealed that the unit treatment cost by flotation process is lower than about $1won/m^3$ compared to a gravity sedimentation process.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.3
• /
• pp.488-496
• /
• 2002

SPME techniques have proven to be very useful tools in the analysis of wide VOCs in the air. In this study, we estimated VOCs in ambient and workplace air using a Tedlar ba /SPME/GC/MS system. The calibration curve was set to be linear over the range of 1-30 ppbv. The detection limits ranged from 10 pptv to 0.93 ppbv for all VOCs. Reproducibility of TO-14 target gas mixtures by SPME/GC/MS averaged at 8.8 R.S.D (%). Air toxic VOCs (hazardous air pollutants, HAPs) containing a total of forty halohydrocarbons, aromatics, and haloaro-matic carbons could be analyzed with significant accuracy, detection limit and linearity at low ppbv level. Only reactive VOCs with low molecular weight, such as chloromethane, vinylchloride, ethylchloride and 1,2-dichloro-ethane, yielded relatively poor results using this technique. In ambient air samples, ten VOCs were identified and quantified after external calibration. VOC concentration in ambient and workplace air ranged from 0.04 to 1.85 ppbv. The overall process was successfully applied to identify and quantify VOCs in ambient/workplace air.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.516-524
• /
• 2012

Selective Laser Sintering(SLS) system consists of various element technologies. Main components of the system include a position control system, a speed control system of the roller, and nitrogen atmosphere furtherance for the powdered sintering. Other systems which make the core of the SLS system are build room and the feed room for powder epitaxial, a temperature control system, and a scan path generator for the laser. The powder material for laser sintering is necessary to produce prototypes in Solid Freeform Fabrication(SFF) based on SLS process. This powder material is sintered in powder room using $CO_2$ laser after spreading evenly using roller to reproduce mold via SFF. This study addresses an SFF system by using the SLS process which applies single laser system to enable manufacturing of 3D shape. And to evaluate applicability of the single laser system, experiments were conducted with optimal fabricating process.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.623-630
• /
• 1995

Silicone rubber-based sodium-selective membranes are developed for solid-state ion sensors. It was shown that the potetiometric performance of SR-based membranes are greatly dependent on the type of neutral carriers employed; among the three ionophores, N,N,N',N'-tetracyclohexyl-1,2-phenylenedioxydiacetamide (ETH 2120), bis[(12-crown-4)methyl]dodecylmethylmalonate (D12C4DMM) and monensin methyl ester (MME), examined, only ETH 2120 was compatible with the SR-based matrix. Addition of about 20 wt% plasticizer to the SR-based matrix provided the resulting membranes with potentiometric properties essentially equivalent to those of the corresponding PVC-based membranes. Owing to the strong adhesive strength of SR-based membranes, the CWEs coated \vith those membranes exhibited long lifetime with conventional electrode-like performance. Blending of PU into the SR matrix increased the lifetime of CWEs from two weeks to one month.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.80-85
• /
• 2009

An experimental study of energy absorption and x-ray emission from ultrashort laser pulse irradiation of in-situ produced solid clusters has been performed. Silver clusters produced by a 30 mJ, 300 ps laser pulse were irradiated up to an intensity of $3{\times}10^{17}\;W/cm^2$ by a 70 mJ, 45 fs compressed laser pulse from the same Ti:sapphire laser. Absorption of the laser light exceeding 70% was observed, resulting in an x-ray yield (>1 keV) of ${\sim}60{\mu}J$ pulse. This may constitute a much simpler means of intense x-ray generation using ultrashort laser pulses as compared to the irradiation of structured / pre-deposited cluster targets, and it offers higher x-ray conversion efficiency than that from gas clusters and planar solid targets.

• Archives of Pharmacal Research
• /
• v.19 no.6
• /
• pp.475-479
• /
• 1996

Diethylcarbamazine (DEC, 1-diethylcarbamyl-4-methylpiperazine) is an antiparasitic piperazine derivative used in the treatment of lymphatic filariasis caused by Wuchereria bancrofti, Brugia malayi or grugia timori. DEC-N-oxide is a major metabolite in humans and has antifilarial activity. In carrying out pharmacokinetic studies, gas chromatographic analysis of DEC in plasma can be complicated by the presence of the metabolite, since the thermally unstable DEC-N-oxide is converted back to a material which coelutes with DEC under the conditions of the analysis. We now report a method to separate DEC-N-oxide from DEC in plasma using solid phase extraction with subsequent gas chromatographic analysis using a nitrogen specific detector. One-diethylcarbamyl-4-ethylpiperazine (E-DEC) was the internal standard. The standard curve of DEC was linear in the range of 10 to 200 ng/ml as described by Y=0.0350+0.0128X, $R^2=0.999$. The limit of quantitation was 4 ng/mL. Reproducibility at 10, 100 and 200 ng/mL concentration points of the standard curve gave coefficient variations of 6.1%, 7.8% and 1.6%, respectively. The recovery following solid phase extraction was 99.3% for DEC and 94.8% for the internal standard. This sensitive and specific analytical method is suitable for pharmacokinetic studies of DEC.