• Bulletin of the Korean Chemical Society
• /
• v.29 no.9
• /
• pp.1673-1677
• /
• 2008

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.234-235
• /
• 2003

All solid-state UV lasers provide efficient, clean and semipermanent light sources for various applications, such as eye surgery, microchip lithography. $CsLiB_{6}O_{10}$ (CLBO) is one of the most suitable crystals for UV generation because of its small walk-off, large effective nonlinear susceptibility in UV region and high damage threshold. We produced fourth (266 nm) and fifth (213 nm) harmonic generation of an Nd：YAG laser (1064 nm) with $LiB_{3}O_{5}$ as a second harmonic generation medium and CLBO as a fourth harmonic and fifth harmonic mediums. (omitted)

• Laser Solutions
• /
• v.15 no.3
• /
• pp.1-6
• /
• 2012

The friction force of patterned needle in elastomer have been investigated to verify the application for bio and plastic industry. The micro pattern on the needle surface were prepared by 266 nm, 20 ns laser and 800 nm, 220 fs laser, which were able to generate the different surface roughness. The friction force was measured by the load cell of 10 N capacity. As the results, the friction force of no patterned needle is almost constant during the needle penetrates the silicone rubber sample. However, the needle having asperities shows the variation of the friction force. The higher the surface roughness is, the smaller the friction force is until the surface roughness is very high. In our experiment conditions, the reduction of the friction force by 20 % compared to no pattern needle was achieved with straight and $50{\mu}m$ discrete line generated by 266 nm, 20 ns laser.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.459-462
• /
• 1999

Recent advances in NLO Borate Crystals for UV Generation are reviewed with the particular emphasis on the technique to improve the life time of UV optics. The laser-damage resistance of CLBO and fused silica surfaces was successfully improved after removing polishing compound by ion beam etching. The polishing compound embedded in the CLBO and fused silica surfaces were to a depth of less than 100nm. We were able to remove polishing compound without degrading the surface condition when the applied ion beam voltage was less than 200 V. The laser-induced surface damage threshold of CLBO was improved up to 15J/$\textrm{cm}^2$(wavelength: 355 nm, pulse width: 0.85 ns)as compared with that of the as-polished surface (11 J/$\textrm{cm}^2$). The laser-induced surface damage of fused silica also increased from 7.5J/$\textrm{cm}^2$ to 15J/$\textrm{cm}^2$. For the irradiation of a 266 nm high-intensity and high-repetition laser light, the surface lifetime of CLBO and fused silica could be more doubled compared with that of the as-polished surface.

• Journal of the Korean Society of Radiology
• /
• v.14 no.6
• /
• pp.833-839
• /
• 2020

Globally, infection prevention and social awareness have been greatly changed by the severe acute respiratory syndrome coronavirus, and as a result, the infection control guidelines and procedures for patients with high exposure to hospital-acquired infection are further strengthened and management and monitoring are more thorough. In order to prevent infection, sterilization should be carried out with the highest priority, and we will find a sterilization method that is low in cost, easy to install, and easy to operate, to present appropriate sterilization effects. In this study, the UV sterilizer was used to contaminate the caries bacteria with an output of 4 W and irradiation time of 60, 150, and 300 sec, and the laser was irradiated with outputs of 0.8 and 1.5 W at wavelengths of 266 and 355 nm, respectively. Ultraviolet sterilizer showed safety in infection prevention at over 150 sec, and laser showed safety in prevention at 1.5 W, 0.8 W, and 266 nm. As a result, the higher the output and the wavelength closer to 253.7 nm, the better the sterilization effect.

• Journal of the Korean Society of Radiology
• /
• v.14 no.5
• /
• pp.695-703
• /
• 2020

The use of medical devices is increasing due to the development of medical technology. Among medical devices, it is often used in the human body for graft and treatment. Therefore, in medical institutions, various sterilization methods according to the type and material of medical devices are applied to prevent infection. Hydrophosphite (HA) materials are the most popular in bone grafts. We would like to present a sterilization method using Q-switch Nd:YAG laser with high output energy among non-ionizing radiation suitable for small medical devices. In this study, sterilization power was most ideally shown at UV wavelengths of 1.5 W, 266 nm, and 10 pulses. Different wavelength bands; infrared and visible light; showed passive sterilization, and ultraviolet A and C showed differences in sterilization according to the pulse. In laser sterilization were differences that found according to the wavelength bands and pulses.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1992.02a
• /
• pp.3-10
• /
• 1992

pphotostimulated desorpption of NO chemisorbed on ppt(001) at 80K has been studied by the (1+1)-resonance-enhanced multipphoton ionization((1+1)-REMppI) technique. A linearly ppolarized ArF excimer laser ( =193 nm, 6.41eV) is used as the ppumpp laser. A high adsorpption rate selectivity was found in the expposure deppendence of the NO desorpption yield. The NO desorpption yield increases drastically when the amount of NO expposure exceeds ~1.8 L. This result shows that the amount of NO sppecies with a large cross section for pphotostimulated desorpption increases drastically at higher NO coverages. Using scanning tunneling microscoppy, we have observed structural modifications of the chlorinated Si(111)-7$\times$7 surface induced by 266nm laser irradiation. At very low laser fluence of 0.7mJ/$\textrm{cm}^2$, at which thermal desorpption can be ignored, a pperiodic stripped ppattern of a single domain is imaged. This ppattern consists of flat terraces and narrow grooves of ~60 and ~10A in width, resppectively.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.462-487
• /
• 1996

We report on the fourth and fifth harmonics generations of Nd:YAG laser radiation realized in CsLiB6O10(CLBO). The values of 500 mJ and 230 mJ at 266 nm and 213 nm were obtained from 2200 mJ of fundamental energy. Doping of CLBO has been carried out and the Al doping was found to give rise to an enhancement of mechanical and chemical properties.

• Journal of Environmental Science International
• /
• v.8 no.6
• /
• pp.699-704
• /
• 1999

The Photodegradation efficient of total organic compounds in the drinking water has been studied using the methods of photocatalytic reaction and laser beam irradation. The results are summarized as follows; 1. The photodegradation efficiency of total organic compounds shows as $50\%\;to\;80\%$ as within one hour and after this the efficiency is decreased slowly. 2. The photodegradation efficiency of total organic compounds shows as 65 to $90\%$ within 3.3min. when Nd : YAG beam is irradiated to the water layer. 3. An excellent observation of the organic compound removal efficiency gives revealed in that case of the longest wavelength of 532nm is irradiated among the three kinds of laser beam sources of 532nm, 355nm and 266nm. 4. The organic compound removal efficiency shows high in the case of UV beam irradiation in the thin layer of water. However the efficiency is not depended on the thickness of water layer severely. 5. The removal efficiency of the organic compounds in the direct irradiation shows higher than the indirect irradiation in the case of UV beam, but the efficiency is not depended on the direction of irradiation in the case of Nd : YAG beam irradiation.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.5
• /
• pp.385-393
• /
• 2001

We have developed a Differential Absortion LIDAR (DIAL) method for the measurement of lower tropospheric ozone concentration. We used two laser beams from quadrupled Nd:YAG (266 nm) for the resonance wavelength and dye lasers (299.5 nm) for non -resonance wavelength. Aerosol extinction coefficients in the lower troposphere was computed by both Klett and Slope methods. To correct the SIN (Signal -Induced Noise) effect caused by photo detector, we subtracted a new-fitted baseline on the background part of a LIDAR signal, after the subtraction of the DC level. This is because SIN can be treated as an exponentially decaying tail. Using theme results, ozone profiles were obtained approximately 2km at daytime and 3km at nighttime. We compared the results derided by the Slope method with those measured by UV spectrometer. The computed results are in mostly good agreement with experimental results. In the measurement of the vertical layer, we observed the variation of the ozone profiles around the top mixed layer.