Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.22
no.10
/
pp.826-831
/
2009
In this paper, a high power RF amplifier module using AlN substrate of high thermal conductivity has been proposed. This RF amplifier module has the advantage of compact size and effective heat dissipation for the packaging of high power chip. To fabricate the thru-hole and scribing line on AlN substrate, the key parameters of $CO_2$ laser were experimented. And then, microstrip lines and spiral planar inductors were fabricated on an AlN substrate using the thin-film process. The fabricated microstrip lines on the AlN substrate has an attenuation value of 0.1 dB/mm up to 10 GHz. The fabricated spiral planar inductor has a high quality factor, a maximum of about 62 at 1 GHz for a 5.65 nH inductor. Packaging of a RF power amplifier was implemented on an AlN substrate with thru-hole. From the measured results, the gain is 24 dB from 13 to 15 GHz and the output power is 33.65 dBm(2.3 W).
Packaging technologies for a broadband and narrowband modulator with a traveling wave electro-absorption modulator (TWEAM) device were developed. In developing a broadband modulator, the effects of the device and packaging designs on the broadband performance were investigated. The optimized designs were obtained through a simulation with the result that we developed a broadband modulator with a 3 dB bandwidth of 38 GHz in the electrical-to-optical (E/O) response, an electrical return loss of less than -10 dB at up to 26 GHz, an rms jitter of 1.832 ps, and an extinction ratio of 5.38 dB in a 40 Gbps non-return to zero (NRZ) eye diagram. For analog application, the effect of the RF termination scheme on the fractional bandwidth was studied. The microstrip line with a double stub as a matching circuit and a laser trimming process were used to obtain an $S_{11}$ of -34.58 dB at 40 GHz and 2.9 GHz bandwidth of less than -15 dB.
Electronic packaging technology is a technology that easily connects devices to the outside. The fourth industrial revolution is thought to be possible with the advancement of certain devices. The advancement of these devices must be accompanied by innovations in electronic packaging that connects the devices to the outside world, allowing their performances to be implemented at the system level. In this paper, the development trends of 2.5D/3D technology, heterogeneous integration technology, ultrafine interconnection technology, and heat dissipation technology will be examined, and the development direction of these technologies will be discussed.
Journal of Korea Technical Association of The Pulp and Paper Industry
/
v.29
no.3
/
pp.69-81
/
1997
Up to now 5 Voith Sulzer paper machines with multi-layer headbox and Gapfor-mer are sucessfully running on papckaging papers. Linerboard, testliner and corugating medium is produced in the basis weight range from 105 to 275 $g/m^2$ at machine speeds up to 900 m/min. The nest one, starting up in Oct. `96 in Germany, will be the world's fastest paper machine for packaging papers. The 5.6 m wide machine is designed for a maximum operating speed of 1200 m/min. Approx. 220.000 tons of corrugating medium and testliner based on 100% waste paper in the basis weight range from 90 to 160 $g/m^2$ will be produced each year. An expansion stage planned for the future is intended to increase annual output to 280.000 tons. This machine will not only be the fastest one for packaging papers, it also comprises all described innovative key components which are available today in order to fulfill growing demands of the future with regard to quality and productivity. The concept of this advanced machine is shown in Fig. 9.
Journal of the Microelectronics and Packaging Society
/
v.28
no.3
/
pp.1-7
/
2021
In this paper, by embedding a bare-die chip-type drive amplifier into the PCB composed of ABF and FR-4, it implements an embedded active device that can be applied in 28 GHz band modules. The ABF has a dielectric constant of 3.2 and a dielectric loss of 0.016. The FR-4 where the drive amplifier is embedded has a dielectric constant of 3.5 and a dielectric loss of 0.02. The proposed embedded module is processed into two structures, and S-parameter properties are confirmed with measurements. The two process structures are an embedding structure of face-up and an embedding structure of face-down. The fabricated module is measured on a designed test board using Taconic's TLY-5A(dielectric constant : 2.17, dielectric loss : 0.0002). The PCB which embedded into the face-down expected better gain performance due to shorter interconnection-line from the RF pad of the Bear-die chip to the pattern of formed layer. But it is verified that the ground at the bottom of the bear-die chip is grounded Through via, resulting in an oscillation. On the other hand, the face-up structure has a stable gain characteristic of more than 10 dB from 25 GHz to 30 GHz, with a gain of 12.32 dB at the center frequency of 28 GHz. The output characteristics of module embedded into the face-up structure are measured using signal generator and spectrum analyzer. When the input power (Pin) of the signal generator was applied from -10 dBm to 20 dBm, the gain compression point (P1dB) of the embedded module was 20.38 dB. Ultimately, the bare-die chip used in this paper was verified through measurement that the oscillation is improved according to the grounding methods when embedding in a PCB. Thus, the module embedded into the face-up structure will be able to be properly used for communication modules in millimeter wave bands.
Proceedings of the International Microelectronics And Packaging Society Conference
/
2000.11a
/
pp.61-64
/
2000
We fabricated and characterized Low Noise Amplifier (LNA) using MCM-C (Multi-Chip-Module-Cofired) technology for 2.14 GHz IMT-2000 mobile terminal application. First, We designed LNA circuits and simulated it's high frequency characteristics using circuits simulator. For the simulation, we adopted high frequency libraries of all the devices used in LNA samples. By the simulation, Gain was 17 dB and Noise Figure was 1.4 dB. We used multilayer process of LTCC (Low Temperature Co-fired Ceramics) substrate and conductor, resistor pattern for the MCM-C LNA fabrication. We made 2 buried inductors, 2 buried capacitors and 3 buried resistors. The number of the total layers was 6. On the top layer, we patterned microstrip line and pads for the SMT device. We measured the high frequency characteristics, and the results were 14.7 dB Gain and 1.5 dB Noise Figure.
Journal of the Microelectronics and Packaging Society
/
v.5
no.2
/
pp.13-20
/
1998
고속 디지털 MCM 응용을 위해 MCM-D 와 MCM-SLC 배선에서 CMOS 버퍼의 신호상승시간에 따른 신호전송특성을 연구하였다. 고속신호처럼 버퍼의 내부저항이 배선의 임피던스보다 작아 발생하게 되는 과도한 ringing은 MCM-D와 같이 lossy line의 전송감쇠 효과로 overshooting 이나 undershooting을 줄일 수 있지만 ringing에 의한 신호왜곡을 근 본적으로 막기위해서는 CMOS버퍼와 배선사이에 적절한 종단을 통해 임피던스 비해 크면 배선의 캐패시턴스에 의해 RC 지연이 증가한다. 그런데 MCM-D 배선은 단위길이당 캐패 시턴스도 작고 배선길이를 줄일수 있으므로 총 RC 지연은 MCM-SLC보다 작았다. 결론적 으로 MCM-D 배선이 MCM-SLC 배선에 비해 고속 디지털 MCM기판으로 적합한 것을 알 수 있었다.
Kim, Hyeon-Wee;Cha, Ik-Soo;Kim, Jin-Ho;Park, Ki-Moon
Korean Journal of Food Science and Technology
/
v.28
no.6
/
pp.1177-1179
/
1996
A static headspace gas chromatographic (HSGC) technique was used to quantify toluene and other solvents (methanol, isopropyl alcohol, methyl ethyl ketone and ethyl acetate) in food packaging films. Comparison of retention times and coefficient variations for standard solvents showed consistent retention time and good reproducibility. Therefore, this method using static HSGC proved to be superior in rapidity and reproducibility, and is thought to be adaptable to analysis of a large number of samples. The methanol content was $N.D.\;(not\;detected){\sim}0.939\;mg/m^2$, toluene $N.D.{\sim}1.403\;mg/m^2$, melthyl ethyl ketone $N.D.{\sim}0.932\;mg/m^2$, total solvent content was $N.D.{\sim}2.433\;mg/m^2$.
In this paper, inductive coupled LC balun has been desi gned and simulated for embedding into an organic packaging substrate. Inductive coupling method was applied to obtain wide band characteristics, and high dielectric film was utilized to reduce a size of the balun. The proposed balun has a novel scheme which consists of three embedded LC resonators with inductive coupling. This proposed balun has relatively small inductance and capacitance values which can be easily embedded into the organic packaging substrate. Furthermore, it has a good phase imbalance characteristic. The simulated results of proposed balun are an insertion loss of 1.2 dB, a return loss of 10 dB, a phase imbalance of 1 degree at frequency bandwidth of 750 MHz ranged from 1.8 GHz to 2.55 GHz, respectively. This balun has an area of $2mm{\tims}3.5mm{\times}0.66mm$ (height).
Proceedings of the International Microelectronics And Packaging Society Conference
/
2003.11a
/
pp.53-58
/
2003
The Wafer Level Packaging is one of the most important technologies in the semiconductor industry today. Its primary advantages are its small form factor and low cost potential for manufacturing including test procedure. The CASIO's WLP samples, application example and the structure are shown in Fig.1, 2&3. There are dielectric layer , under bump metal, re-distribution layer, copper post , encapsulation material and terminal solder .The key technologies are 'Electroplating thick copper process' and 'Unique wafer encapsulation process'. These are very effective in getting electrical and mechanical advantages of package. (Fig. 4). CASIO and CMK are developing a new System Packaging technology called the Embedded Wafer Level Package (EWLP) together. The active components (semiconductor chip) in the WLP structure are embedded into the Printed Wiring Board during their manufacturing process. This new technical approach has many advantages that can respond to requirements for future mobile products. The unique feature of this EWLP technology is that it doesn't contain any solder interconnection inside. In addition to improved electrical performance, EWLP can enable the improvement of module reliability. (Fig.5) The CASIO's WLP Technology will become the effective solution of 'KGD problem in System Packaging'. (Fig. 6) The EWLP sample shown in Fig.7 including three chips in the WLP form has almost same structure wi_th SoC's. Also, this module technology are suitable for RF and Analog system applications. (Fig. 8)
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.